GTE Omni Scbs Installation And Maintenance Manual
Have a look at the manual GTE Omni Scbs Installation And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
FEATURES PACKAGES A AND B DEFAULT PACKAGE C DEFAULT DATA BASE DATA BASE ACCESS CODES (FAC) ACCESS CODES (FAC) SCC 1 Access 40 40 (Basic) 46 (Expanded) 1 SCC 2 Access I 42 1 42 (Basic) 47 (Expanded) I I SCC 3 Access SCC 4 Access Station Speed Calling I 43 I 43 (Basic) 48 IExoanded) I 44 *0 + user programmed SPC (O-9) 44 (Basic) 49 (Expanded) *O + user programmed SPC (O-9) I System Speed Calling I ## + installer programmed SPC (00-99) I ## + installer programmed SPC (00-99) I I Save/Beoeat Last Number Dialed I *a *0 I EKT Paging Access - All Zone/Zone EKT Paging Answer (Package B) 77 + for all zones or l-9 for each zone 87 + for all zones or l-9 for each zone 77 + for all zones or 1-9 for each zone 87 + for all zones or 1-9 for each zone External Paging Access - All Zone/Zone (Package B) External Paging Answer (Package B) Call Forwarding - All Calls Activate 78 + for all zones or 1-9 for each zone 78 + for all zones or 1-9 for each zone *34 + STA DN 78 + for all zones or 1-9 for each zone 78 + for all zones or 1-9 for each zone *34 + STA DNIATT Access 1 Call Forwardina - All Calls Cancel *30 *30 I Call Forwarding - Busy No Answer Activate Call Forwarding - No Answer Activate *33 + STA DN *32 + STA DN *33 + STA DNlATT Access *32 + STA DNIATT Access Call Forwarding - Busy/No Answer and No Answer Cancel I *31 *31 I Do-Not-Disturb Activate Do-Not-Disturb Cancel Message Leaving Activate Message Leaving Cancel Message Pickup *6 *6 #6 #6 *l + STA DN *l + STA DN #l + STA DN #+STADN *5 *5 2.29.1
FEATURES Station Camp-On Cancel PACKAGES A AND B DEFAULT PACKAGE C DEFAULT DATA BASE DATA BASE ACCESS CODES (FAC) ACCESS CODES (FAC) #* #* 1 Trunk Camp-On Cancel I #7 I #7 I 1 G LOUD Pickuo I *4 I *4 I Call Park Answer Night Answer Pick Up (self-tenant) Night Answer Pick Up (all-tenant) #9 + Call Park Orbit No. (l-4 digits) #30 #31 #9 + Call Park Orbit No. (1-4 digits) #30 #31 Directed Call Pick Up DSS Park Answer Data Call Attribute Change Do Not Disturb Override Activate Do Not Disturb Override Cancel Automatic ‘intercom User Programmability Station Speed Call User Programmability ll+STADN 18 + Orbit No. (3 digits) 69 + Parameter *2 + STA DN #2 #4 + (button key) + STA DN or SPCC #O+SPC+TAC+DN 17+STADN 18 + Orbit No. (3 digits) 69 + Parameter *2 + STA DN #2 #4 + (button key) + STA DN or SAC + SPC #O+SPC+TAC+DN Off-Hook Incoming Call Signaling Change (EKT only) 57 + 0 for lamp only or 1 for ringing 57 + 0 for lamp only or 1 for ringing Call Announce Receive ON/OFF (EKT only) (see CMC 101) #8 + 1 for ON or 0 to disallow #8 + 1 for ON or 0 to disallow Pre-selection Mode Change (Basic) 542 + 0 = cancel 1 = activate I Ringing Line Preference Change I I 541 + 0 = cancel 1 = ICM 2 = ICM ortrunk ~ 1 Idle Line Preference Change Direct Trunk Access Day/Night Mode Change (this tenant only) 6l* + trunk DN *# + 0 day or 1 = night 541 + 0 = cancel 1 = ICM 2 = trunk 61* + trunk DN *# + 0 dav or 1 = niaht 2.30
FEATURES PACKAGES A AND B DEFAULT PACKAGE C DEFAULT DATA BASE DATA BASE ACCESS CODES (FAC) ACCESS CODES IFACI I Limited Executive Override (overrides only stations with higher COR) I #5 I #5 1 1 Call Park Activate I *9 + 3 digit orbit no. I *9 + 3 diait orbit no. I Add Data Call Set Up (Package B) 67 67 I Account Code/Client Billing 56 + identifier (1 to 15 digits) 56 + identifier (1 to 15 digits) I I Executive Override (extends Limited Override I #5 (not in default data base, must add COS of I #5 (not in default data base, must add COS of to override all stations) this feature at CMC 104, same code) this feature at CMC 104, same code) I NOTES: 1. SPC = Speed Access Code: Station = O-9 progrtammed by user, System = 00-99 programmed by installer. 2. TAC = Trunk Feature Access Code (listed this table) 3. DN = Directory Number or Station Number 4. EKT = Electronic Key Telephone 2.30.1
DESCRIPTION Iigit Receive Incoming digit receive time cut Incoming interdigit time cut PACKAGES AI0 PACKAGE C DEFAULT VALUE DEFAULT VALUE IN SECONDS IN SECONDS (* 0.2) (* 0.2) 11.26 11.26 7.17 7.17 CMC TABLE 254 254 Digit Send Pm-pause timing (manual) Interdigit timing (10 pps) lnterdigit timing (20 pps) Pre-pause timing (speed call) Interdigit pause (speed call) Interdigit timing (DTMF) jystem Timing Station hook signal (maximum before disconnect Call start time after sending all digits Confirmation tone time cut Confirmation tone burst Sewice Registration time cut Call Forwarding - No Answer timing Station Camp-On callback release Station Camp-On ringback Station Camp-On release Trunk Camp-On callback cancel Trunk Camp-On cancel Call Park recall No Answer recall Recalled station look-in Called party release DSS Camp-On recall DSS Call Hold recal! Long hold recall (line and ICM hold) Forward All Calls and DND reminder Preselection Release (future) Camp-On burst 2.30 0.66 (DP) 3.3 2.1 (PB) 3.0 (DP) 0.06 1.05 16.40 11.26 0.70 2.05 13.31 31.74 31.74 infinite 11.26 infinite 62.46 31.74 2.05 1.02 31.74 31.74 165.34 0.7 11.26 2.05 2.05 254 0.77 (DP) 254 0.51 3.1 254 2.05 254 0.13 254 1.05 103 16.40 103 11.26 103 0.70 103 2.05 103 13.31 103 31.74 103 31.74 103 infinite 103 11.26 103 infinite 103 62.46 103 31.74 103 2.05 103 1.02 103 31.74 103 31.74 103 165.34 103 0.7 103 4.1 103 0.2 103 Override warning burst Paging warning burst (internal and external) BT, ROT timing Call anncunce warning burst Pre-pause for second DT (LCR. SCC) Account code registration display timing Direct-in line called party busy burst timing Direct-in line called party look-in timing Paging EKT calling timing Station hold loop recall timing Automatic release for DISA ROT Reseizure for DMR hunt failure of .TIE/DID Attendant Call Park recall Attendant Camp-On recall Attendant long hold recall Attendant transfer call recall Attendant incoming overflow timing Common hold operation Delayed ringing timing Verify display timing CFT timing for wake-up anwer Central Office line release timeout. Maximum duration of off-cycle incoming ringing CT timing from incoming answer tc transmission Trunk guard release Ground trunk seizure time cut Flash timing (disconnect) 0 DEFAULT STANDARD TlMlNG VALUES ASSOCIATED WITH TRANSMISSION AND TRUNK ROUTE TIMING MAY BE CHANGED WITH CMC-254. . ALL DEFAULT STAPlDARD TIMING VALUES ASSOCIATED WITH SYSTEM OR STATION FEATURES MAY BE CHANGED WITH CMC-103. 2.31
_-_ efault Stander iz DIALING DESTINATION Local/Toll Operator International Operator Toll Prefix International Prefix Special Number Office Code DIALING PATTERN 0 01 1 011 N-II NNX Area Code NO/IX Station Number x to xxxx NOTES: 1. X=Oto9, N=2to9 2. Type of call available: NNX + XXXX I+ NNX + XXXX NO/IX + NNX + XXXX I+ NO/IX + NNX + XXXX 0 + (time out) 0 + NNX + XXXX 0 + NO/IX + NNX + XXXX Nil 01-l+ 12X’s 2.32
Guide to Data ase Programming at Time f System Imst OPERATIONAL VERIFICATION f PROGRAM PROGRAM PROGRAM BASIC TRUNK TERMINATIONS APPLICABLE + PROGRAM APPLICABLE DATA SERVICE cos FUNCTIONS PROGRAM PROGRAM TRUNK PROGRAM TERMINATIONS OR KEY - TRUNK DIALING SMDR MULTI-DIGIT + SYSTEMFEATURES DATA RESTRICTION. ANWOR LCR SAVE 0008 TO PERFORM TAPE OR FLOPPY - oPERAT’oNAL VERIFICATION COMPLETION OKXETTE PROCEO”RES PROGRAM SBCS BEHIND A PABX, PROGRAM TENANT ASSIGNMENT, - DATA STATION - AN0 OPX FEATURES 2.33
view Exercise - Data Base INSTRUCTIONS: THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, TRUE/FALSE, FILL IN THE BLANK, OR MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E. STUDENT WORKBOOK, NOTES, AND GTEP MANUAL) MAY BE USED AS REFERENCES. SUBMIT EXERCISE TO INSTRUCTOR FOR GRADING WHEN LAST QUESTION HAS BEEN COMPLETED. 1. THE OMNI SBCS OPERATING SYSTEM SOFTWARE AND DEFAULT DATA BASE RESIDE ON BOTH THE AND CARDS. 2. PROGRAM CHANGES CAN BE MADE WITH THE OR INSTRUMENTS. 3. SPECIAL FUNCTIONS (ADD/CHANGE, ETC.) ARE PERFORMED WITH THE KEYS WHEN USING THE PMP. 4. THE PORTABLE MAINTENANCE PANEL USUALLY INTERFACES TO THE OMNI SBCS THROUGH RS-232-C PORT ~. 5. WHEN IS THE PMP CONTROL PROGRAM LOADED INTO THE PMP? 6. THE SECURITY CODE FOR HIGH SECURITY ACCESS IS AND LOW SECURITY ACCESS IS WITH SVR 1.5.x.x. 7. MATCH EACH OF THE FOLLOWING PF KEYS WITH ITS CORRECT FUNCTION: PFl A. SELECT SHIFT + PF5 B. RELEASE PF3 C. CANCEL PF2 D. ADD/CHANGE RETURN E. REMOVE 8. A CMC TABLE CAN HAVE UP TO PARAMETERS. 9. CMC COMMAND PARAMETER VALUES ARE ENTERED FROM THE PMP KEYBOARD USING AND KEYS. IO. WHAT PARAMETER DOES THE SYSTEM REQUIRE TO BE INPUT FOR MOST CMC COMMANDS? , 2.34
Review Exercise - Data Base Overview (2.1) (Continued) 11. 12. 13. 14. 15. 16. 17. 16. 19. 20. WHAT IS DISPLAYED ON THE PMP SCREEN IF THE SECURITY CODE IS NOT ACCEPTED BY THE SYSTEM? . THE PROCEDURE LOADS AND ESTABLISHES THE SYSTEM DEFAULT STANDARD DATA BASE. THE PORTABLE MAINTENANCE PANEL IS USED PRIMARILY: A. AS AN INSTRUCTIONAL DEVICE TO TEACH CUSTOMERS ABOUT OMNI SBCS FEATURES. B. FOR PERFORMING ROUTINE MAINTENANCE, CREATING OR MODIFYING THE OMNI SBCS DATA BASE, AND ISOLATING HARDWARE FAULTS. C. FOR PROGRAMMING NEW OMNI SBCS SOFTWARE PROGRAMS. D. FOR LEARNING THE CHILL HIGH-LEVEL PROGRAMMING LANGUAGE. THE CURSOR MAY BE MOVED AROUND THE CMC COMMAND SCREEN THROUGH THE USE OF OR . WHAT MESSAGE IS DISPLAYED IF A LOW SECURITY CODE IS ENTERED AND ENTRY TO A CMC COMMAND TABLE REQUIRING HIGH ACCESS THEN IS ATTEMPTED? A MINUTE BLANK MICROCASSETTE TAPE IS REQUIRED TO MAKE A BACK-UP OF THE PMP CONTROL PROGRAM. MODIFICATIONS TO A CMC COMMAND TABLE ARE NOT ENTERED INTO THE DATA BASE UNTIL: LOCAL PMP CONNECTION TO THE OMNI SBCS REQUIRES USE OF A CABLE. THE DEFAULT PMP PORT CONFIGURATION IS SET TO BAUD WITH THE ECHO TURNED . THE DEFAULT STATUS FOR THE NUMBER OF SIMULTANEOUS CALLS ALLOWED IN THE SYSTEM IS , INDEPENDENT OF DATA BASE CHANGES. 2.35
,_.--. 21. 22. WHAT SCREEN IS DISPLAYED WHEN THE PMP IS IN “COMMAND MODE”? WHAT IS THE PROCEDURE FOR OBTAINING A HARD COPY OF A CMC COMMAND WITH CURRENT PARAMETER STATUS? 23. (TRUE OR FALSE) THE PMP CANNOT COMMUNICATE WITH THE OMNI SBS IF THE MEM AND SWC CARDS HAVE NOT BEEN SEATED. 24. OMNI SBCS DATA BASE TABLES ARE ADDRESSED BY A THREE-DIGIT: . 25. THE OMNI SBCS DEFAULT STANDARD STATION DIRECTORY NUMBERING PLANS BEGINS WITH DIRECTORY NUMBER AND ENDS WITH . 2.36