GTE Omni Scbs Installation And Maintenance Manual
Have a look at the manual GTE Omni Scbs Installation And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Programming Basic ai!mw sLm3 4. SELECT THE TYPES OF SlGNALlNG WHlCH ARE AVAILABLE WHEN ADDING TRUNKS: A. WINK, DELAY, OR IMMEDIATE B. E&M OR INCOMING C. DIAL PULSE OR DTMF D. GROUND OR LOOP 5. IDENTIFY THE DEFAULT STANDARD TRUNK GROUP NUMBERS FOR THE FOLLOWING TRUNKS: co E&M TIE LOOP START TIE 6. WHAT ARE THE REQUIRED PARAMETERS WHEN ADDING A WATS TRUNK LINE WITH CMC-250? 7. WHY WOULD A “NOT RGTR” MESSAGE BE DISPLAYED WHEN ADDING TRUNK EQUIPMENT NUMBER 184 IN THE LAB? 2.78
eview Exercise 2 3) 0 GE OMNI SEES 8. WHAT ERROR MESSAGE WILL BE DISPLAYED IF A LOOP TIE TRUNK IS ADDED AT CMC-250 WITH A VALUE OF 1 ENTERED FOR PARAMETER 5? 9. CIRCUITS ON THE CARD ARE ASSIGNED TO TRUNK GROUP NUMBER 1 BY DEFAULT. IO. WHAT ARE THE ADVANTAGES OF CHANGING A TRUNK’S DIAL MODE TO DTMF? 11. THE OMNI SBCS WILL ALLOW TENANT TRUNK GROUPS. 12. WHAT OCCURS WHEN A STATION FROM A DIFFERENT TENANT GROUP TRIES TO ACCESS A TRUNK THAT IS NOT IN THEIR TENANT GROUP? 13. IN THE LAB, ATTEMPT TO REMOVE ONE OF THE CO TRUNKS WITH CMC-250 WITHOUT CHANGING CMC-251. WHAT HAPPENS TO THE DIAL MODE AND BREAK RATIO AT CMC-251? 14. EXPLAIN THE DIFFERENCE BETWEEN TM1 AND TM2 TIMING VALUES WHEN ASSIGNING AN SCC TRUNK. 2.79
, Review Exercise - Programming Basic 15. WHAT IS THE DEFAULT FEATURE ACCESS CODE FOR EACH TRUNK ACCESS: __ CO#l - WATS#l - TIE #I (E&M) - TIE #2 (LOOP) - SCC#l 16. MATCH EACH OF THE FOLLOWING TERMS WITH ITS CORRECT DEFINITION: ~ TRUNK FEATURE ACCESS CODES ___ TRUNK GROUP NUMBER A. USED BY SYSTEM TO ACCESS SCC NETWORK - SIGNALING B. GROUND OR LOOP START ~ DIAL MODE/BREAK RATIO C. ASSIGNMENT IDENTIFYING GROUPS OF -TERMINATING TRUNK GROUP NUMBER TRUNKS TERMINATING TO STATION -TRUNK EQUIPMENT NUMBER INSTRUMENTS -GATE OFFICE DIRECTORY NUMBER D. DIAL PULSE OR DTMF E. CARD SLOT AND CIRCUIT NUMBER F. ALLOWS DIRECT CONNECTION TO SPECIFIC TRUNK GROUPS G. ASSIGNMENT GROUP BASED ON TYPE OF TRUNKS. 17. MATCH EACH OF THE FOLLOWING CMC COMMANDS WITH ITS CORRECT DESCRIPTION. - CMC-250 A. __ CMC-251 B. NIGHT ANSWER ASSIGNMENT (STATIONS AND TRUNKS) SCC ROUTING TRUNK GROUP NUMBER ASSIGNMENT - CMC-253 C. TRUNK DATA ASSIGNMENT __ CMC-306 D. TRUNK ASSIGNMENT - CMC-307 E. SCC ASSIGNMENT - CMC-404 F. DIRECT-IN LINE ASSIGNMENT - CMC-405 G. TERMINATING TRUNK GROUP ASSIGNMENT 2.80
DATA BASE ADMINISTRATION Programming Trunk Terminations 2.82
GIVEN: @ GTE OMNI SBCS . GTE OMNI SBCS PERIPHERALS @ PORTABLE MAINTENANCE PANEL @ GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE @ LABORATORY ACTIVITY - PROGRAMMING TRUNK TERMINATIONS @ REVIEW EXERCISE ACTION: CRITERIA: 0 USE OMNI SBCS PROGRAMMING TOOLS AND EQUIPMENT TO: - ASSIGN A DIRECT-IN LINE. - ASSIGN KEY SYSTEM TRUNK LINE TO EKT STATION. - CREATE A PERSONAL/PRIVATE TRUNK LINE. - ASSIGN POOLED INCOMING TRUNK LINES. - ASSIGN POOLED OUTGOING TRUNK LINES. - ASSIGN POOLED BOTHWAY TRUNK LINES. . COMPLETE REVIEW EXERCISE. . DEMONSTRATION OF ABOVE TASKS IN ACCORDANCE WITH PROCEDURES OUTLINED IN OMNI SBCS GTEP MANUAL AND OMNI SBCS STUDENT WORKBOOK. . REVIEW EXERCISE WILL BE COMPLETED CORRECTLY IN ACCORDANCE WITH PASS/FAIL CRITERIA OF THIS TRAINING ORGANIZATION. 2.83
Programming Trunk Terminations/ werwiew DESCRIPTION 1 . TRUNKS CAN BE TERMINATED TO SINGLE LINE TELEPHONE SETS OR TO BUTTONS ON ELECTRONIC KEY TELEPHONE SETS. . DEFAULT STANDARD DATA BASE ASSIGNS ALL TRUNK GROUPS TO TRUNK GROUP 13 UPON INSTALLATION. . TERMINATING TRUNK GROUP (TTGN) ASSIGNMENTS MUST BE SPECIFIED TO TERMINATE TRUNKS TO STATION INSTRUMENTS. . TYPES OF TRUNK TERMINATIONS: DIRECT-IN TRUNK LINE - DIRECT TERMINATION OF CO TRUNK LINE TO SLT OR EKT INSTRUMENT, BYPASSING A BLF/DSS ANSWERING STATION. DOES NOT REQUIRE TERMINATION TO BUTTON ON EKT. KEY SYSTEM TRUNK LINE - EMULATES OPERATION OF TRADITIONAL KEY TELEPHONE SYSTEM BY ONE OR MORE EKT STATION’S BUTTONS BEING PROGRAMMED TO HAVE ACCESS TO A SPECIFIC TRUNK LINE. PERSONAL/PRIVATE LINE - RESERVES ONE TRUNK LINE FOR INCOMING AND/OR OUTGOING CALLS FOR ONE SPECIFIC EKT STATION. POOLED INCOMING TRUNK - ALLOWS INCOMING TRUNK LINES TO BE POOLED INTO A GROUP TERMINATING TRUNK GROUP CONNECTED TO MULTIPLE STATIONS (BYPASSING A BLF/DSS ANSWERING STATION). EACH CONNECTED STATION WILL HAVE LINE APPEARANCE OF INCOMING TRUNK. 2.84
Programming Trunk Terminations/ wiew (C POOLED OUTGOING TRUNK - ALLOWS OUTGOING TRUNK LINES TO BE POOLED INTO A GROUP TERMINATING TRUNK GROUP CONNECTED TO MULTIPLE STATIONS. EACH CONNECTED STATION WILL HAVE LINE APPEARANCE FOR OUTGOING POOLED TRUNKS WITH ACCESS TO CO, WATS, OR FX TRUNK CALLS. POOLED BOTHWAY TRUNK - ALLOWS BOTHWAY TRUNK LINES TO BE POOLED INTO A GROUP TERMINATING TRUNK GROUP CONNECTED TO MULTIPLE STATIONS. EACH CONNECTED STATION WILL HAVE LINE APPEARANCE FOR TWO-WAY POOLED TRUNKS WITH DIRECT ACCESS TO INCOMING OR OUTGOING CAPABILITIES. 2.85
,_. ,-- . ing Trunk Terminations F MULTIPLE REMARKS ASSIGNED TO AN OUTGOING TRUNK GROUP SIMULTANEOUSLY POOLED BUTTONS OTHER NOT LIMITED 1 TRUNK GROUP A BOTHWAY TRUNK OUTGOING THAN FEATURE PER BUTTON ASSIGNED TO THIS TRUNK TRUNK GROUP ACCESS BUTTONS DIRECT-IN NO BUTTON NOT ASSIGNABLE NOTE: MAXIMUM OF 31 TRUNK GROUPS CAN BE ASSIGNED 2.86
Programming Trunk Terminations/Diagram of Trunk Termination Assignments GE m!mw sms BOTHWAY TRUNK GROUP DIRECT-IN + DIRECT-IN- --- I -- --- it if ---- ---mm ii k i t-~..-i..-.---j .-.. +.. ; r-T-y-- -.. -.. -- ..-. . - ! j i :TJ+’ i.., :: i II i II / I I EKT I I EKT 1 1 --- .a-- ---- _-- - .--- --- -..-..-BOTHWAY -----0UTGOlNG - - - - -INCOMING DIRECT-IN 2.87