GTE Omni Scbs Installation And Maintenance Manual
Have a look at the manual GTE Omni Scbs Installation And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Service Functions/ St&o DESCRIPTION @ NlGHT ANSWER ASSIGNMENT ALLOWS BNCOMING CALLS TO BE DlRECTED TO A SPEClFlC NIGHT ANSWER STATlON OR TO ACTIVATE A NIGHT BELL WHICH ALLOWS A PICK-UP BY ANY INTERNAL STATION. @ SYSTEM DEFAULT CAPACITY IS 16 NIGHT ANSWER GROUPS* WITH UP TO 8 MEMBERS IN EACH GROUP. o DEFAULT ACCESS CODE TO ANSWER NIGHT RINGING CALL IS #31 (ALL TENANT) OR #30 (SELF TENANT). NOTE: ACCESS CODE MAY BE CHANGED WITH CMC-100. Q, AT LEAST ONE TRUNK AND ONE STATION MUST BE ASSIGNED TO INITIALIZE NIGHT ANSWER FEATURE. PROCEDURE f 1. USE CMC-306 TO ASSIGN: @ NIGHT ANSWER GROUP NUMBER (PI) @ TRUNK/STATION FLAG (P2) @ EQUIPMENT NUMBER (P3) 2. USE CMC-201 AND CMC-251 (IF APPLICABLE) TO CHECK TENANT ASSIGNMENTS *PACKAGE C ALLOWS 32 NIGHT ANSWER GROUPS. NOTES: @ IF NIGHT BELL IS SELECTED FOR NIGHT ANSWER OPERATION, THE BELL MUST BE PROGRAMMED AS A STATION (ASSIGNED AN EQUIPMENT NUMBER), PHYSICALLY CONNECTED TO DESIRED CIRCUIT ON 8SLC CARD, AND RGEN MUST BE INSTALLED. @ EXISTING TRUNK OR §TATION ASSlGNMEtiTS MUST BE DELETED BY REMOVE PROGRAM FUNCTION BEFORE CHANGING OR REMOWING NIGHT GROUP ASSIGNMENTS. 2.108
Programming Service Functions/ CMC Command Summary e e e e 0 0 0 CATEGORY CM6 TABLE FUNCTION SYSTEM SPEED CALLING 300 ADDS, REMOVES, OR CHANGES SYSTEM DIRECTORY SPEED CALLING DIRECTORY NUMBERS. STATION HUNT GROUP ASSIGNMENT 301 ASSIGNS, REMOVES, OR CHANGES VOICE OR DATA FROM ONE OF THREE TYPES OF HUNT GROUPS: CIRCULAR, TERMINATING OR PILOT. PICKUP GROUP ASSIGNMENT 302 ASSIGNS, REMOVES OR CHANGES STATIONS FROM PICK-UP GROUPS. EKT SYSTEM PAGING GROUP 303 ASSIGNS, REMOVES OR CHANGES EKT ASSIGNMENT STATIONS FROM PAGING ZONES. HOT LINE STATION 304 ASSIGNS, REMOVES OR CHANGES ASSIGNMENT STATIONS FROM HOT LINE SERVICE MUSIC ON HOLD 305 ASSIGNS OR REMOVES MUSIC ON HOLD ASSIGNMENT SERVICE NIGHT ANSWER STATION 306 ASSIGNS, REMOVES OR CHANGES ASSIGNMENT STATIONS OR TRUNKS FROM NIGHT RING GROUPS.
DESCRIPTION @ NlGHT ANSWER ASSIGNMENT ALLOWS lNCOMlNG CALLS TO BE DIRECTED TO A SPEClFlC NlGHT ANSWER STATION OR TO ACTlVATE A NIGHT BELL WHICH ALLOWS A PICK-UP BY ANY lNTERNAL STATION. @ SYSTEM DEFAULT CAPACITY IS 16 NIGHT ANSWER GROUPS* WITH UP TO 8 MEMBERS IN EACH GROUP. 8 DEFAULT ACCESS CODE TO ANSWER NIGHT RINGING CALL IS #3l (ALL TENANT) OR #30 (SELF TENANT). NOTE: ACCESS CODE MAY BE CHANGED WITH CMC-100. @ AT LEAST ONE TRUNK AND ONE STATION MUST BE ASSIGNED TO INITIALIZE NIGHT ANSWER FEATURE. PROCEDURE 1. USE CMC-306 TO ASSIGN: 0 NIGHT ANSWER GROUP NUMBER (PI) 0 TRUNK/STATION FLAG (P2) @ EQUIPMENT NUMBER (P3) 2. USE CMC-201 AND CMC-251 (IF APPLICABLE) TO CHECK TENANT ASSIGNMENTS *PACKAGE C ALLOWS 32 NIGHT ANSWER GROUPS. NOTES: @ IF NIGHT BELL IS SELECTED FOR NIGHT ANSWER OPERATION, THE BELL MUST BE PROGRAMMED AS A STATION (ASSIGNED A EQUIPMENT NUMBER), PHYSICALLY CONNECTED TO DESIRED CIRCUIT ON 8SLC CARD, AND RGEN MUST BE INSTALLED. @ EXISTING TRUNK OR STATION ASSlGNMEtiiS MUST BE DELETED BY REMOVE PROGRAM FUNCTION BEFORE CHANGING OR REMOVING NIGHT GROUP ASSIIGNMENTS. 2.108
Programming rvice Cunctions/ C Comma Summary CATEGORY CM6 TABLE FUNCTION @ SYSTEM SPEED CALLING 300 ADDS, REMOVES, OR CHANGES SYSTEM DIRECTORY SPEED CALLlNG DIRECTORY NUMBERS. @ STATION HUNT GROUP ASSIGNMENT 301 ASSIGNS, REMOVES, OR CHANGES VOICE OR DATA FROM ONE OF THREE TYPES OF HUNT GROUPS: CIRCULAR, TERMINATING OR PILOT. @ PICKUP GROUP 302 ASSIGNS, REMOVES OR CHANGES ASSIGNMENT STATIONS FROM PICK-UP GROUPS. @ EKT SYSTEM PAGING GROUP 303 ASSIGNS, REMOVES OR CHANGES EKT ASSIGNMENT STATIONS FROM PAGING ZONES. l HOT LINE STATION 304 ASSIGNS, REMOVES OR CHANGES ASSIGNMENT STATIONS FROM HOT LINE SERVICE . MUSIC ON HOLD ASSIGNMENT . NIGHT ANSWER STATION ASSIGNMENT 305 306 ASSIGNS OR REMOVES MUSIC ON HOLD SERVICE ASSIGNS, REMOVES OR CHANGES STATIONS OR TRUNKS FROM NIGHT RING GROUPS. 2.109
- Programming PERFORM THE FOLLOWING PROGRAMMlNG TASKS IN THE SEQUENCE OUTLlNED BELOW USING THE SAMPLE WORK ORDERS AND IN ACCORDANCE WITH THE GTE OMNl SBCS GTEP MANUAL. COMPLETE THE REVlEW EXERCISE QUESTIONS PERTAINING TO PROGRAMMING SERVICE FUNCTIONS UPON COMPLETION OF THIS LABORATORY ACTIVITY. WORK ORDER #2.5 ZOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-1212 -0CATION: RESTON, VlRGlNfA WORK ORDER #2.5 (TASK #1) )RfGfNATOR: TELECOMMUNICATIONS MANAGER TASKS: l Establish a system speed calling directory with CMC-300. (1) Add the following numbers and access (1) Perform programming change for service codes to the system speed calling directory: (2) Check/test the operation of changes after SPEED DIAL: completion of this portion of the laboratory CODE ACCESS CODE SEND NUMBER (3) Proceed to next work order task. 00 75 (FOR CO TRUNK 1) 301 555 1221 01 75 02 75 202 936 1111 2.110
Laboratory Activity - Programming PBS (Continued) ml ah%mw SBCS 1 WORK ORDER # 2.5 -I :OMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-1212 -0CATION: RESTON, VIRGINIA WORK ORDER # 2.5 (TASK #2) )RlGlNATOR: TELECOMMUNICATIONS MANAGER -ASKS: l Assign stations to a hunt group with CMC-301. ‘ARAMETERS: INSTRUCTIONS: (1) Assign stations to a terminating type hunt (1) Perform programming change for service group using the following parameters: function. TERMINATING (2) Check/test the operation of changes after STATION DN HUNT GROUP # ORDER completion of this portion of the laboratory activity. 214 1 1 308 1 2 (3) Proceed to next work order task. 212 1 3 223 1 4 2.111
WORK ORDER #2.5 COMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 LOCATION: RESTON, VfRGlNlA WORK ORDER # 2.5 (TASK #3) DRIGINATOR: TELECOMMUNICATIONS MANAGER TASKS: e Assign stations to a pickup group with CMC-302. (1) Assign the following stations to designated pickup groups. PICKUP GROUP 1 1 1 2 2 2 STATION DN (2) Check/test the operation of changes after completion of this portion of the laboratory (3) Proceed to next work order task. 2.112
Laboratory Activity - Programming Service ens (Continue WORK ORDER # 2.5 :OMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-1212 .OCATION: RESTON, VIRGINIA WORK ORDER #2.5 (TASK #4) IRIGINATOR: TELECOMMUNICATIONS MANAGER -ASKS: l Create a hot line service with CMC-304. ‘ARAMETERS: INSTRUCTIONS: (1) Assign hot line service using the following (1) Perform programming change for service parameters: function. Hot line number = 1 (2) Check/test the operation of changes after Originating station = 216 completion of this portion of the laboratory Terminating station = 223 activity. (3) Proceed to next work order task. 2.113
WORK ORDER # 2.5 IOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 -0CATION: RESTON, VIRGINIA WORK ORDER #2.5 (TASK #5) )RtGlNATOR: TELECOMMUNICATIONS MANAGER -ASKS: e Remove hot line service with CMC-304. e Create an internal paging group with CMC-303. (1) Remove previously assigned hot line service (1) Perform programming changes for service from station directory numbers 216 and 225. functions. (2) Assign all CS-20 and CS-10 EKT instruments to (2) Check/test the operation of changes after paging group 1. completion of this portion of the laboratory NOTE: Programming of external zone paging (3) Proceed to next work order task. (speaker amplifier) will be addressed in Module IV. 2.114
Laboratory hnctio Programming Service COMPLETE MUSIC-ON-HOLD SERVICE FUNCTION TASK IF TIME PERMITS OR IF INSTRUCTOR DIRECTS YOU TO DO SO. WORK ORDER # 2.5 COMPANY NAME: NU SYSTEM CO. LOCATION: RESTON, VIRGINIA 3RIGINATOR: TELECOMMUNICATIONS MANAGER TASKS: PHONE #: (703) 5551212 WORK ORDER #2.5 (TASK #6) l Assign music-on-hold with CMC-305. PARAMETERS: INSTRUCTIONS: (1) Verify that the music-on-hold service has been (1) Perform programming change for service physically connected to circuit on 4BWC card function. and music source assigned to correct trunk circuit (slot 18, circuit 2) with CMC-250. (2) Check the operation of changes after completion of this portion of the laboratory (2) Activate the music-on-hold service with CMC- activity. 305 using the equipment number designated above. (3) Proceed to next work order task. 2.115