GTE Omni Scbs Installation And Maintenance Manual
Have a look at the manual GTE Omni Scbs Installation And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
,,-. Systemwide Programming Changes/ ering Plan Assignment Gull 1 DESCRIPTION 1 @ DEFAULT STANDARD SYSTEM NUMBERING PLAN DEFINING FEATURE NUMBERS, FEATURE ACCESS CODES, TRUNK GROUP NUMBERS, AND SEND AND SAVE/SEND AS DIALED FOR TIE LINES. I PROCEDURE I * IDENTIFY FEATURE ACCESS CODES TO BE CHANGED USING DEFAULT STANDARD TABLE. 1. USE CMC-100 TO CHANGE: - FEATURE NUMBER (PI) - FEATURE ACCESS CODE (P2) - TRUNK GROUP NUMBER (P3) - OUTGOING DIRECTORY NUMBER (P4) - ACCESS CODE DIGITS TO BE SENT FOR TIE ACCESS ONLY (P5) - DIAL AND STORE AND FORWARD FLAG (P6) Pl: 92 P4: * CAUTION SHOULD BE EXERCISED TO ENSURE THAT ANY MODIFICATION OF FEATURE ACCESS CODES DOES NOT CONFLICT WITH EXISTING FEATURE ACCESS CODES OR STATION DIRECTORY NUMBER ASSIGNMENTS. 2.136
Systemwide Progra Parameter Assignment 1 DESCRIPTION 1 . ALLOWS FLAGS TO BE SET FOR THE FOLLOWING SERVICE FUNCTIONS: - A CHECK FOR TRUNK-TO-TRUNK TRANSFER RESTRICTION. - INDICATION OF WHETHER A WARNING BURST (TONE) INTERRUPTS USERS WHEN EXECUTIVE OVERRIDE FEATURE IS ACTIVATED. - DESIGNATION OF VOICE OR TONE OPTION WHEN CALL ANNOUNCE INTERCOM FEATURE IS ACTIVATED. @ WHILE DEFAULT SYSTEM CAPACITY FOR SYSTEM FLAGS IS 32, ONLY 3 FLAGS (AS DEFINED ABOVE) CAN BE USED AT THE PRESENT TIME. REMAINING FLAGS HAVE BEEN RESERVED FOR PROGRAM USE OR FOR FUTURE ENHANCEMENTS. 1 PROCEDURE 1 * 1. USE CMC-I 01 TO ASSIGN: - SYSTEM FLAG IDENTIFICATION NUMBER (PI) - FLAG VALUE (0 OK 1) (P2) CMC=lOl i Pl: 3 P2: 1 * CM6 TABLE IN OMNI SBCS GTEP MANUAL CONTAINS THE AVAILABLE INDENTIFICATION NUMBERS AND VALUES FOR SYSTEM SERVICE FEATURES. 2.137
1 DESCRIPTION 1 Gull aimnn SBCS @ ALLQWS CHANGE OF TI ING PARAMETERS FOR VARIOUS SYSTEM FUNCTIONS. ACTUAL TIMING FOR EACH TIMING PARAMETER IS CALCULATED BY MULTIPLYING THE TIMING PARAMETER’S DESIGNATED FIXED UNIT BY A MULTIPLER VALUE (0 TO 255). EXAMPLE: FOR DSS CAMP-ON RECALL (PARAMETER I), FIXED TIMING UNIT IS 1024 ms. THE DEFAULT MULTIPLIER (PARAMETER 2) IS 31: 1024 ms X 31 = 31.1744 SECONDS TO INCREASE TIME TO APPROXIMATELY ONE MINUTE, CHANGE VALUE FOR PARAMETER 2 TQ 60: 1024 ms X 60 = 6144 SECONDS 1 PRQCEDURE I* 1. USE CMC-103 TO SELECT: - SYSTEM TIMING IDENTIFICATION NUMBER (PI) - MULTIPLIER (P2) NOTE: CMC TABLE IN OMMI SBCS GTEP MANUAL CONTAINS IDENTIFICATION NUMBER FOR ALL SYSTEM TIMING FUNCTIONS. 2.138
Systemwide Pr ming Changes/System Parameter Assignment GTE alMm!i SBCS ( . ALLOWS UP TO 26 FLAGS TO BE SET FOR VARIOUS SYSTEM FUNCTIONS. 1 PROCEDURE I* 1. USE CMC-102 TO ADD/CHANGE: - FLAG NUMBER (PI) - SET FLAG VALUE (P2) CMC=lO2 n Pl: 6 P2: 1 * SEE CMC TABLE IN OMNI SBCS GTEP MANUAL, FOR A LISTING OF FLAG NUMBERS AND APPROPRIATE SETTING OF PARAMETER VALUES. REFER TO CMC TABLE IN OMNI SBCS GTEP MANUAL WHEN CHANGING FLAG NUMBER 5 (SIGNALING CHECK FOR TRUNK TO TRUNK CONNECTION RESTRICTION). 2.139
stem-wide Programming Changes/ Network L Ian Assignment [ DESCRIPTION 1 e ALLOWS CHANGE IN DIGITAL PAD CIRCUIT (PAD) VALUE TO IMPROVE QUALITY OF INCOMING OR OUTGOING CONNECTIONS. 1 PROCEDURE I* DETERMINE WHICH INCOMING OR OUTGOING ROUTES ARE AFFECTED BY CIRCUIT LOSS QUALITY. IDENTIFY SPECIFIC CIRCUITS THAT ARE EXPERIENCING CIRCUIT LOSS. 1. USE CMC-106 TO CHANGE VALUE OF DIGITAL PAD: - INCOMING ROUTE (PI) CMC=lO6 - OUTGOING ROUTE (P2) r-l Pl: 2 - VALUE OF DIGITAL PADDING CIRCUIT (P3) P2: 5 P3: 4 * SEE CMC TABLE IN OMNI SBCS GTEP MANUAL, FOR A LISTING OF AVAILABLE INCOMING/OUTGOING ROUTE PARAMETERS. SEE CMC TABLE IN OMNI SBCS GTEP MANUAL, FOR A LISTING OF AVAILABLE DECIBEL (dB) LEVELS FOR PAD VALUE PARAMETERS. 2.140
System-Wide Programming Changes/ Trunk Route Timins @ SETS TRUNK ROUTE TIMING PARAMETER FOR VARIOUS SYSTEM TRUNK ROUTES l TIMING IS CALCULATED BY MULTIPLYING THE TRUNK’S FIXED TIMING UNIT (IN ms) BY A DESIGNATED MULTIPLER. [PROCEDUREI 1. USE CMC-254 TO ASSIGN: CMC=254 Pl: 13 . TRUNK GROUP NUMBER (PI) . ROUTE TIMING ID NUMBER (P2) . NORMALIZED TIMING/MULTIPLIER (P3) 0 P2: 1 P3: 14 * REFER TO CMC TABLE IN OMNI SBCS GTEP MANUAL FOR DESCRIPTIONS OF AVAILABLE ROUTE TIMING AND MULTIPLIER FOR NORMALIZED TIMING. 2.141
System-wide Programming Change&MC and Summary CATEGORY . NUMBERING PLAN ASSIGNMENT . SERVICE PARAMETER ASSIGNMENT l SYSTEM PARAMETERS ASSIGNMENT . SYSTEM TIMING PARAMETER ASSIGNMENT . NETWORK LOSS (PAD) CONTROL @ TRUNK ROUTE TIMING CMC TABLE CMC-100 CMC-101 CMC-102 CMC-103 CMC-106 CMC-254 FUNCTION DEFINES DEFAULT STANDARD SYSTEM NUMBERING PLAN (FEATURE NUMBERS, FEATURE ACCESS CODES, TRUNK GROUP NUMBERS, ETC.) DEFINES SYSTEM SERVICE FUNCTION PARAMETERS. DEFINES SYSTEM FUNCTION PARAMETERS. DEFINES SYSTEM TIMING PARAMETERS. DEFINES DIGITAL PAD CIRCUIT VALUES. SETS THE TRUNK ROUTE TIMING PARAMETER. 2.142
PERFORM THE FOLLOWING PROGRAMMING TASKS IN THE SEQUENCE OUTLINED BELOW USING THE SAMPLE WORK ORDERS AND IN ACCORDANCE WITH THE GTE QMNI SBCS GTEP MANUAL. COMPLETE THE REVIEW EXERCISE QUESTIONS PERTAINING TO SYSTEM-WIDE PROGRAMMING CHANGES UPON COMPLETION OF THIS LABORATORY ACTIVITY. WORK ORDER #2.7 :OMPANY NAME: NU SYSTEM CO. PHONE ?+: (703) 555-1212 CCAT’CN: RESTON, VIRGINIA WORK ORDER # 2.7 (TASK #l) )R’G’NATCR: TELECOMMUNICATIONS MANAGER ASKS: e Modify default standard numbering plan with CMC-100. (1) Change the feature access code for (1) Perform programming changes for system- “Save/Repeat Last Number Dialed” from “8” wide function. (default) to 89 (Parameters 3, 4, 5, and 6 will be blank). (2) Check/test the operation of changes after completion of this portion of the laboratory (3) Proceed to next work order task. 2.143
-_ WORK ORDER #2.7 :OMPANY NAME: NU SYSTEM CC. PHONE #: (703) 5551212 .QCATION: RESTON, VIRGINIA WORK ORDER #2.7 (TASK #2) )RfGINATOR: TELECOMMUNICATIONS MANAGER ‘ASKS: l Change a service parameter flag with CMC-101. (1) Change the flag indicating whether a warning (1) Perform programming changes for system- burst is heard during executive override, to wide function. “send burst”. (2) Check/test the operation of changes after completion of this portion of the laboratory (3) Proceed to the next work order task. 2.144
Laboratory Activity - System-Wide Programming Changes (Continued) GTE awn SBm WORK ORDER #2.7 COMPANY NAME: NU SYSTEM CO. LOCATION: RESTON, VIRGINIA DRIGINATOR: TELECOMMUNICATIONS MANAGER PHONE #: (703) 555-1212 WORK ORDER #2.7 (TASK #3) TASKS: l Change a system parameter flag with CMC-102. PARAMETERS: INSTRUCTIONS: (1) Change the flag indicating the type of ringing pattern for off-premises extensions to “recall ringing.” NOTE: Programming off-premises extensions will be addressed in later module. (1) Perform programming change for system-wide function. (2) Check/test the operation of changes after completion of this portion of the laboratory activity. (3) Proceed to next work order task. 2.145