GTE Omni Scbs Installation And Maintenance Manual
Have a look at the manual GTE Omni Scbs Installation And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Software and Distributed Processor Version Number Displays i DESCRIPTION 1 GTE aww a3cs 1 1 @ CMC-904 WILL DlSPLAY CURRENT SYSTEM SOFTWARE VERSION’ NUMBER INDICATING: - FEATURE PACKAGE BY ALPHABETIC CHARACTER - SAVE/LOAD OPERATION CAPABILITY - RELEASE VERSION WITH ENHANCEMENTS AFFECTING DOCUMENTATION, TECHNICAL OR SALES TRAINING. - POINT RELEASE VERSION WITH ENHANCEMENTS NOT AFFECTING USER OPERATION . CMC-907 WILL DISPLAY CURRENT DISTRI,BUTED PROCESSOR VERSION NUMBER FOR ANY CARD IN INTERFACE CARD GROUP. I PROCEDURE 1 1. USE CMC-904 TO OBTAIN CURRENT SOFTWARE VERSION NUMBER. ENTER BISPLAY AT PI. . VERSION ID (PI): FORMAT 6 01 1. 1 C@lC=904 cl ‘Pl: BOI 1.2 17130 FEATURE PACKAGE SAVE/LOAD COMPATIBILITY r’ T T ‘: ;L’NJ-;;EASE 3.21
Ssfkware and Distributed Braces r&ion N 2. USE CMC-907 TO OBTAIN CURRENT VERSlON NUMBER FOR lNTERFACE CARD. ENTER DISPLAY AT Pl: . EQUIPMENT NUMBER (PI) . CARD TYPE (P2) 1: 8SLC 2: 4BWC 3: 2TTE CMC=907 Pl: 040 cl P2: 1 P3: 0 4: 2TTL 5: 4DMR . VERSION NUMBER (P3) NOTE: WHEN THE CARD FOR SPECIFIED EQUIPMENT NUMBER IS NOT INSTALLED OR IS AN 8EKC OR 8DTC CARD, THE CARD TYPE AND VERSION NUMBER CORRESPONDING TO THE NEXT CARD (EXCEPT FOR 8EKC OR 8DTC) ARE DISPLAYED. 3.22
Device Status Display 1 DESCRIPTION 1 o CMC-800 iDISPLAYS A SERIES OF THREE SCREENS BRIEFLY LISTING FAULTY DEVICES AND LOCATIONS. MORE DETAILED INFORMATION ABOUT THESE FAULTS CAN BE OBTAINED WITH CMC-801. l FOLLOWING ABBREVIATIONS FOR FAULTY DEVICES MAY BE LISTED: DEVICE ABBREVIATION DEVICE NAME cc RAM RTS BAT swc ICG TRM SCI RG CPM CARD OR MEM CARD RAM ON CPM CARD OR MEM CARD REAL TIME SOURCE ON CPM CARD BATTERY SWC CARD TRUNK/LINE CARD ELECTRONIC KEY TELEPHONE INSTRUMENT RS-232-C PORT RGEN CARD ’ . THREE DEVICE STATUS SCREENS MAY BE DISPLAYED IN SEQUENCE: SCREEN ONE - HIGH LEVEL FAULT SUMMARY SCREEN TWO - LINE/TRUNK CARD AND RS-232-C PORT STATUS SCREEN THREE - EKT STATUS . EACH FAULTY DEVICE IS DISPLAYED IN A FIXED POSITION ON THE SCREEN: PI: %C RAM RTS BAT P2: ICG TRM SCI P3: RG 3.23
pii5Gcq 1. ENTER CMC-800. AT PI, PRESS DBSPLAY TO DISPLAY SCREEN ONE. GTE aww SBCS CMC=800 DSP cl ::; ICG TRM P3: 2. AT PI, PRESS DISPLAY TO DISPLAY SCREEN TWO*: r CMC=800 DSP Pl: ICG&SCI STATUS P2: 0000000000 P3: 000000100 00 3. AT PI, PRESS DISPLAY TO DISPLAY AT SCREEN THREE*: CMC=800 DSP Pl : FAULT TERMINAL 4. IF hi0 OTHER INFORMATION IS AVAILABLE, SCREENS ARE SKIPPED AND END IS DISPLAYED). METER VALUES ARE DESCRIBED IN 0 NI SBCS GTEP MANUAL, (MAINTENANCE SECTION, CMC-800). 3.24
Fault Log Display 1 DESCRIPTION 1 0 PROVIDES DETAILED FAULT INFORMATION FOR TROUBLE-SHOOTING INCLUDING: - DEVICE NAME AND EQUIPMENT NUMBER - TIME OF FAULT OCCURRENCE OR REPAIR - CAUSED FACTOR AND SUPPLEMENTARY FAULT DATA READING OUT FAULT LOG TURNS THE ALARM AND TIMER OVERFLOW LAMPS OFF AND INITIALIZES THE WATCH DOG TIMER RESTART COUNTER TO ZERO. FAULT INFORMATjON IS DISPLAYED IN HISTORICAL ORDER OF OCCURRENCE WITH MOST RECENT FAULT DISPLAYED LAST. MAXIMUM OF 16 FAULTS IS STORED. WHEN NUMBER OF FAULTS EXCEEDS CAPACITY, OLDEST FAULT IS DELETED AND MOST RECENT FAULT IS ADDED TO THE LOG. MAKING A HARDCOPY PRINTOUT OF EACH FAULT LISTING IS RECOMMENDED. 3.25
d Fault Log Display (Continued) 1 PROCEDURE 1 1. 2. 3. ENTER CMC-801. AT PI PRESS DISPLAY TO DISPLAY OLDEST FAULT LISTING IN LOG: CONTINUED TO PRESS DISPLAY AT Pl UNTIL ALL FAULTS LISTED IN LOG HAVE BEEN DISPLAYED: AFTER ALL FAULTS HAVE BEEN LISTED FROM LOG, END IS DISPLAYED: 3.26 CMC=801 DSP PI: TRM P4: 026 P2: 11: 22 02/28 P3: 0 c CMC=801 DSP Pl: TRM P4: 005 P2: 12:16 02/03 P3: 1 I CMC= END cl
NAME DEVICE OR EQUIPMENT NUMBER (P4) CdUSED FACTOR (P3) FAULT DATA (P4) (SEE NEXT PAGE) &MCARDOR MEM CARD 200 OR 0 - COLD RESTART 210 1 = WATCH DOG TIMER OVER-FLOW 2 : SOFTWARE MAZE 3 = RAM DATA PROBLEM 4 - ILLEGAL INTERRUPTION 5 MANUALHOT RESTART RAM RAM ON CPM OR MEM CARD RTS REAL TIME SOURCE ON CPM CARD BAT BATTERY swc SWC CARD ICG TRUNK/LINE CARD TRM PROPRIETARY TELEPHONE SCI RS-232-C PORl 200 2 ILLEGAL TIME FIRST EN ON CARD EN OF EKT OR DSS PORT NO 000/001 0 = TURN ALM LAMP OFF 1 RAM MEMORY STACK 2 RAM PROTECTION 0 RECOVERY 1 STOP INCREMENTING 2 = ILLEGAL TIME 0 RECOVERY 1 DISCHARGE 0 TURN ALM LAMP OFF 1 = CLOCK FAILED 2 - CM MEMORY STACK 3 RSM MEMORY STACK 4 SSM MEMORY STACK 0 RECOVERY 1 DATA TRANSMISSION ERROR 2 - ICG AUDIT ERROR 0 7 RECOVERY 1 DATA TRANSMISSION ERROR 2 EKT AUDIT ERROR 0 RECOVERY 1 DATA TRANSMISSION ERROR 2 -. SEND DATA TIME OUT 0 RECOVERY 1 = RGEN FAULT 1.2) SEGMENT ADDRESS 3,4) OFFSET ADDRESS B&TACK DATA 1,2) SEGMENT ADDRESS 3,4) OFFSET ADDRESS gj READ DATA 7) WRITE DATA 1.2) READ AFTER WRITE DATA 5.6) CM ADDRESS 1) READ AFTER WRITE DATA 5.6) RSM ADDRESS 1) READ AFTER WRITE DATA 5,6) SSM ADDRESS RG RGEN CARD 1 RGEN FAULT 3.27
Fault Log Display (Continued) 1 PROCEDURE 1 1. 2. 3. ENTER CMC-801. AT PI PRESS DISPLAY TO DISPLAY OLDEST FAULT LISTING IN LOG: CONTINUED TO PRESS DISPLAY AT Pl UNTIL ALL FAULTS LISTED IN LOG HAVE BEEN DISPLAYED: AFTER ALL FAULTS HAVE BEEN LISTED FROM LOG, END IS DISPLAYED: CMC=801 DSP Pl: TRM P4: 026 P2: 11: 22 02/28 P3: 0 I CMC=801 DSP Pl: TRM P4: 005 P2: 12:16 02/03 P3: 1 CMC= END . 3.26
CMC-801: DE”,CE NAME DEVICE OR EQUIPMENT NUMBER (P4) 200 OR 210 CiUSED FACTOR (Pa) 0 - COLD RESTART 1 = WATCH DOG TIMER OVER-FLOW 2 SOFTWARE MAZE 3 .- RAM DATA PROBLEM 4 - ILLEGAL INTERRUPTION 5 MANUAL HOT RESTART FAULT DATA (P4) (SEE NEXT PAGE) RAM RAM ON CPM OR MEM CARD 0 : TURN ALM LAMP OFF 1 - RAM MEMORY STACK 2 RAM PROTECTION RTS REAL TIME SOURCE ON CPM CARD BAT BATTERY swc SWC CARD ICG TRUNK/LINE CARD TRM PROPRIETARY TELEPHONE SCI RS-232-C PORT ZEN CARD 200 2 ILLEGAL TIME 190 FIRST EN ON CARD EN OF EKT OR DSS PORT NO. 000/00~ 1 RGEN FAULT 0 RECOVERY 1 STOP INCREMENTING 2 = ILLEGAL TIME 0 RECOVERY 1 DISCHARGE 0 TURN ALM LAMP OFF 1 = CLOCK FAILED 2 - CM MEMORY STACK 3 RSM MEMORY STACK 4 SSM MEMORY STACK 0 RECOVERY 1 DATA TRANSMISSION ERROR 2 - ICG AUDIT ERROR 0 : RECOVERY 1 DATA TRANSMISSION ERROR 2 EKT AUDIT ERROR 0 RECOVERY 1 DATA TRANSMISSION ERROR 2 SEND DATA TIME OUT 0 1 RECOVERY 1 = RGEN FAULT 1.2) SEGMENT ADDRESS 3.4) OFFSET ADDRESS B.&TACK DATA 1.2) SEGMENT ADDRESS 3,4) OFFSET ADDRESS ii READ DATA 7) WRITE DATA 1.2) READ AFTER WRITE DATA 5.6) CM ADDRESS 1) READ AFTER WRITE DATA 5.6) RSM ADDRESS 1) READ AFTER WRITE DATA 5,6) SSM ADDRESS 3.27