GTE Omni Scbs Installation And Maintenance Manual

							Programming Toll and Multi-Digit/ 
Restriction Assignment 
1 DESCRIPTION 1 
. RESTRICTS CONNECTION TO CO (INCLUDING FX OR WATS) AND TIE TRUNK LINES. 
. 16 COR LEVELS MAY BE ASSIGNED WITH COR LEVEL 1 BEING LEAST RESTRICTIVE AND COR LEVEL 16 BEING MOST 
RESTRICTIVE. 
. COR DESIGNATION MAY BE MADE SEPARATELY FOR INCOMING OR OUTGOING CONNECTIONS. 
. DEFAULT DATA BASE ASSIGNS ALL STATIONS AND TRUNK GROUPS TO COR LEVEL 1 WHICH ALLOWS ACCESS AND 
CONNECTION TO ALL AVAILABLE TRUNK GROUPS. 
REVIEW DEFAULT COR TABLE TO IDENTIFY ANY RESTRICTIONS TO BE ADDED OR REMOVED FROM COR LEVELS. 
1. IF DESIRED USE CMC-105 TO ASSIGN OR CHANGE RESTRICTION TO EACH COR LEVEL: 
. CLASS OF RESTRICTION (PI) 
. RESTRICTION ON OUTGOING CONNECTIONS TO CO LINES (INCLUDING FX AND 
WATS) (P2) 
@ RESTRICTION ON INCOMING CONNECTIONS FROM CO LINES (INCLUDING FX AND 
WATS) (P3) 
. RESTRICTION ON OUTGOING CONNECTIONS TO TIE LINES (P4) 
. RESTRICTION ON INCOMING CONNECTIONS FROM TIE LINES (P5) 
2. IF DESIRED USE CMC-202 TO ASSIGN OR CHANGE COR FOR EACH STATION: 
. STATION DIRECTORY NUMBER (PI) 
. CLASS OF SERVICE IN DAY MODE (P2) 
. CLASS OF SERVICE IN NIGHT MODE (P3) 
. CLASS OF RESTRICTION IN DAY MODE (P4) 
a CLASS OF RESTRICTION IN NIGHT MODE (P5) 
3. IF DESIRED USE CMC-252 TO ASSIGN OR CHANGE COR FOR EACH TRUNK GROUP: 
. TRUNK GROUP NUMBER (PI) 
. CLASS OF SERVICE IN DAY MODE (P2) 
. CLASS OF SERVICE IN NIGHT MODE (P3) 
. CLASS OF RESTRICTION IN DAY MODE (P4) 
. CLASS OF RESTRICTION IN NIGHT MODE (PS) 
2.166 CMC=202 
PI: 417.P4: 1 
P2: 1 P5: 3 
P3: 3 
. 
CMC=252 
r 
PI: 14 P4:l 
P2: 1 P5: 3 
P3: 3  
						

							ogrammi 
striction 
stricti B and Multi-Digit/ 
nd Office Code 
ts 
@ DEFINES AREA CODE AND OFFICE CODE RESTRICTIONS FOR OUTGOING TRUNK GROUPS TO 
CONTROL TOLL EXPENSES AND PREVENT TELEPHONE ABUSE. 
* RESTRICTED AREA CODES AND OFFICE CODES MUST BE DETERMINED AND ASSIGNED TO AREA 
CODE, OFFICE CODE, AND AREA/OFFICE CODE TABLE. THESE TABLES ARE ASSIGNED TO CLASS OF 
RESTRICTION ON AN ALLOWED OR DENIED BASIS. 
Q SYSTEM BLOCKS ANY CALLS PLACED TO RESTRICTED AREA CODES OR OFFICE CODES. 
@ SYSTEM CAPACITY IS TOTAL OF 1000 AREA AND OFFICE CODES IN COMBINED RESTRICTION TABLES. 
f-Ficzq 
1. USE CMC-411 TO ESTABLISH TOLL AND OPERATOR CALL RESTRICTION NUMBERS: 
e RESTRICTION GROUP NUMBER (Pl) 
. CLASS OF RESTRICTION 
. FLAG IDENTIFICATION VALUE (P3)** 
. FLAG VALUE (P4)** 
CMC=411 
P1:3 P4:O 
P2: 1 
P3: 1 
2. USE CMC-413 TO DEFINE AREA CODES TO BE INCLUDED IN RESTRICTION TABLE: 
. RESTRICTION GROUP NUMBER (Pl) 
. CLASS OF RESTRICTION (P2) 
Pl: 1 P4: 301 
@ CALLS ALLOWED/DENIED FLAG (P3)* 
. AREA CODE (P4) 
NOTE: REPEAT ABOVE STEPS TO ASSIGN OTHER AREA CODES. 
*ALLOW OR DENY FLAG AFFECTS ALL AREA AND OFFICE CODES WHICH PREVIOUSLY HAVE BEEN 
ASSIGNED TO RESTRICTION TABLE. MOST RECENT SETTING OVERRIDES EARLIER SETTINGS. 
2.167  
						

							Programming Toll and Multi-Digit 
Restriction/ Area/Office Co’de 
estriction Assignment 
1-1 (Continued) 
3. 
USE CMC-412 TO DEFINE OFFICE CODES TO BE INCLUDED IN RESTRICTION TABLE: 
. RESTRICTION GROUP NUMBER (Pi) 
. CLASS OF RESTRICTION (P2) 
CMC=412 
. CALLS ALLOWED/DENIED FLAG (P3)* Pl: 1 P4: 279 
. OFFICE CODE (P4) 
cl P2: 3 
P3: 1 
NOTE: REPEAT ABOVE STEPS TO ADD OTHER OFFICE CODES. 
4. 
USE CMC-414 TO DEFINE COMBINED OFFICE AND AREA CODES TO BE INCLUDED IN RESTRICTION 
TABLE: 
. RESTRICTION GROUP NUMBER (PI) 
l CLASS OF RESTRICTION (P2) CMC=414 
. CALLS ALLOWED/DENIED FLAG (P3)* Pl: 2 P4: 301 
. AREA CODE (P4) 
P2: 6 P5: 270 
P3: 1 
. OFFICE CODE (P5) 
NOTE: REPEAT STEPS TO ADD OTHER COMBINED OFFICE AND AREA CODES. 
*ALLOW OR DENY FLAG AFFECTS ALL AREA AND OFFICE CODES WHICH PREVIOUSLY HAVE BEEN 
ASSIGNED TO RESTRICTION TABLE. MOST RECENT SETTING OVERRIDES EARLIER SETTINGS. 
**REFER TO OMNI SBCS GTEP MANUAL, CMC TABLE FOR LIST OF FLAG IDENTIFICATION NUMBERS AND FLAG VALUES. 
2.168  
						

							. CMC-400 ASSIGNS DIALING GROUP AND RESTRICTION GROUP NUMBERS TO DESIGNATED TRUNK GROUP NUMBERS. 
. CMC-401 IDENTIFIES CUSTOMER TOLL PREFIX CODES AND OPERATOR TOLL PREFIX CODES WITH TRUNK DIAL 
GROUP NUMBERS. DEFAULT SETTING FOR CUSTOMER TOLL PREFIX IS l+. DEFAULT SETTING FOR OPERATOR TOLL 
PREFIX IS O+. 
. CMC-402 PROVIDES ASSIGNMENT FOR THOSE AREAS WHICH REQUIRE A PROGRAMMED NO/lx OFFICE CODE DUE TO 
CONFLICTING OFFICE AND AREA CODES (E.G., LOS ANGELES, CHICAGO, NEW YORK, ETC.) 
[PROCEDURES 
1. USE CMC-400 TO ASSIGN: 
CMC=400 
. TRUNK GROUP NUMBER (Pl) 
rl Pl: 13 
. DIAL GROUP NUMBER (P2) P2: 1 
. TOLL RESTRICTION GROUP NUMBER (P3) P3: 2 
2. USE CMC-401 TO ASSIGN: 
. DIAL GROUP NUMBER (Pl) 
. CUSTOMER TOLL PREFIX CODE (P2) 
. OPERATOR TOLL PREFIX CODE (P3) 
NOTE: UP TO THREE DIAL GROUPS MAY BE ASSIGNED. 
3. USE CMC-402 TO ASSIGN NO/IX OFFICE CODE: 
. TOLL PREFIX REQUIRED (Pl) 
. DIAL GROUP NUMBER (P2) 
. REGISTRATION DIGIT FLAG (P3) 
. REGISTRATION DIGITS (P4) . 
CMC=401 
Pl: 2 
P2: 1 
P3: 0 
I 
I 
I 
CMC=402 
Pl: 1 P4: 312 
P2: 2 
P3: 1 
2.169  
						

							-- 
Programming Toll and Multi-Digit 
Restriction/,SCC Restriction Assignment 
GTE 0M.U SBCS 
(DESCRIPTION 1 
e DEFINES SCC ACCESS CODE RESTRICTION TABLE AND ASSIGNS TABLE 
TO RESTRICTION GROUPS BASED ON CLASS OF RESTRICTION. 
. UP TO 10 CARRIER ACCESS CODES MAY BE ASSIGNED TO EACH COR. 
1 PROCEDURE 1 
1. IF APPLICABLE USE CMC-415 TO ASSIGN/REMOVE: 
CMC=415 
. RESTRICTION GROUP NUMBER (PI) Pl: 2 
. CLASS OF RESTRICTION (P2) 
L-J P2: 3 
P3: 10288 
a CARRIER ACCESS CODE (P3) 
2.170  
						

							Programming Toll and Multi-Digit 
Restriction/CMC Command Summarv 
0 
0 
0 
0 
0 
0 
l 
0 
0 
0 
0 
CATEGORY CMC TABLE 
TRUNK RESTRICTION CMC 105 
STATION CLASS OF 
RESTRICTION CMC 202 
TRUNK CLASS OF 
RESTRICTION CMC 252 ASSIGNS COR TO TRUNKS FOR DAY/NIGHT MODE 
TRUNK DIALING GROUP/ 
RESTRICTION GROUP 
ASSIGNMENT 
TOLL PREFIX AND 
OPERATOR ACCESS 
CODE ASSIGNMENT 
NO/lx OFFICE CODE 
ASSIGNMENT 
TOLL AND OPERATOR 
CALL RESTRICTION 
ASSIGNMENT 
OFFICE CODE 
RESTRICTION 
AREA CODE 
RESTRICTION 
AREA/OFFICE CODE 
RESTRICTION 
CARRIER ACCESS CODE 
RESTRICTION CMC 400 
CMC 401 
CMC 402 
CMC 411 
CMC 412 ASSIGNS OFFICE CODE RESTRICTIONS FOR OUTGOING TRUNK GROUPS 
CMC 413 ASSIGNS AREA CODE RESTRICTIONS FOR OUTGOING TRUNK GROUPS 
CMC 414 ASSIGNS AREA/OFFICE CODE RESTRICTIONS FOR OUTGOING TRUNK 
GROUPS 
CMC 415 DEFINES CARRIER ACCESS CODE RESTRICTION TABLE  ASSIGNS TRUNK RESTRICTION TO COR 
ASSIGNS COR TO STATIONS FOR DAY/NIGHT MODE 
ASSIGNS DIALING GROUP AND RESTRICTION GROUP NUMBERS TO TRUNK 
GROUP NUMBERS 
ASSIGNS CUSTOMER TOLL PREFIX AND OPERATOR TOLL PREFIX TO TRUNK 
DIAL GROUP NUMBERS 
ASSIGNS NO/lx OFFICE CODE TO IDENTIFY EITHER OFFICE OR AREA CODE 
CORRESPONDING TO DIAL GROUP NUMBER 
ASSIGNS TOLL AND OPERATOR RESTRICTION NUMBERS 
2.171  
						

							PROGRAMMING UPON COMPLETION OF THIS LABORATORY SETTING. 
. 
Laboratory Activity - Multi-Digit 
Restriction Programming (Continued) 
GE OMNU SBCS 
PERFORM THE FOLLOWING PROGRAMMING TASKS IN THE SEQUENCE OUTLINED BELOW USING 
THE SAMPLE WORK ORDERS AND IN ACCORDANCE WITH THE GTE OMNI SBCS GTEP MANUAL. 
COMPLETE THE REVIEW EXERCISE QUESTIONS PERTAINING TO MULTI-DIGIT RESTRICTION 
WORK ORDER #2.9 
COMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 
LOCATION: 
RESTON, VIRGINIA WORK ORDER #2.9 (TASK #l) 
DRIGINATOR: 
TELECOMMUNICATIONS MANAGER 
TASKS: 
l Reassign trunk circuits to trunk group numbers with CMC-250. 
(1) Reassign each of the following trunks to the (1) Perform programming changes for trunks 
designated trunk group and type of trunk using required for Multi-digit restriction laboratory 
CMC-250: 
EN 160 to TGN 31 (TIE 1) 
EN 161 to TGN 32 (TIE 2) (2) Check/test the operation of changes after 
EN 170 to TGN 33 (TIE 3) completion of this portion of the laboratory 
EN 171 to TGN 34 (TIE 4) 
(3) Proceed to next work order task. 
NOTE: Existing trunks must be removed 
before new values can be added.  
						

							Laboratory Activity - Multi-Digit 
Restriction Progra 
ing (Co tinued) 
GE OMNU SBCS 
WORK ORDER #2.9 
ZOMPANY NAME: NU SYSTEM CG: 
.OCATION: RESTON, VIRGINIA 
IR.lGINATOR: TELECOMMUNICATIONS MANAGER 
;ASKS: PHONE #: (703) 555-1212 
WORK ORDER 2.9 (TASK #2) 
0 Assign station directory numbers to Class of Restriction with CMC-202. 
‘ARAMETERS: INSTRUCTIONS: 
(1) Assign the following stations to the’following (1) Perform programming changes for Multi-digit 
designated COR levels: 
Restriction. 
DN=212toCORl 
(2) Check-test the operation of changes after 
completion of this portion of the laboratory 
DN=215toCOR2 activity. 
DN = 208 to COR 3 (3) Proceed with next work order task. 
2.173  
						

							Laboratory 
estriction Iti-IBisit 
WORK ORDER #2.9 
COMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-1212 
-0CATION: RESTON, VIRGINIA WORK ORDER 2.9 (TASK #3) 
3RIGINATOR: TELECOMMUNICATIONS MANAGER 
TASKS: 
e Assign trunk group numbers to dial groups and restriction groups with CMC-400. 
e Assign customer toll prefix and operator access codes to dial groups with CMC-401. 
(1) Assign TGN 13 to dialing group number 1 and (1) Perform programming changes for Multi-digit 
restriction group number 1 using CMC-400. Restriction. 
(2) Assign CTP 1 and OTP 0 to dialing group (2) Check/test the operation of this portion of the 
number 1. laboratory activity. 
(3) Proceed with next work order task. 
2.174  
						

							Laboratory Activity - Multi-Digit 
Restriction Programming (Continued 
WORK ORDER #2.9 
COMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 
-0CATION: 
RESTON, VIRGINIA WORK ORDER 2.9 (TASK #4) 
3RIGINATOR: TELECOMMUNICATIONS MANAGER 
TASKS: 
l Assign toll restrictions to a restriction group and assign the restriction groups to a Class 
of Restriction with CMC-411. 
PARAMETERS: 
INSTRUCTIONS: 
(1) Assign the following toll restrictions and COR (1) Perform programming changes for Multi-Digit 
levels to the following designated restriction 
Restriction. 
groups: 
RGN = 1 COR = 1 FLAG ID = 1 FLAG VALUE = 0 
RGN = 1 COR = 1 
FLAG ID = 2 FLAG VALUE = 0 
RGN= 1 COR= 1 FLAG ID=3 FLAGVALUE=O 
RGN= 1 COR= 1 FLAG ID=4 FLAGVALUE=l 
RGN = 1 COR = 1 FLAG ID = 5 FLAG VALUE = 0 
RGN = 1 COR = 1 
FLAG ID = 6 FLAG VALUE = 0 
RGN = 1 COR = 1 FLAG ID = 7 FLAG VALUE = 1 
RGN = 1 COR = 2 
FLAG ID = 1 FLAG VALUE = 1 
RGN = 1 COR = 2 FLAG ID = 2 FLAG VALUE = 1 
RGN = 1 COR = 2 FLAG ID = 3 FLAG VALUE = 0 
RGN = I COR = 2 FLAG ID = 4 FLAG VALUE = 0 
RGN = I COR = 2 FLAG ID = 5 FLAG VALUE = 0 
RGN = 1 COR = 2 
FLAG ID = 6 FLAG VALUE = 0 
RGN = 1 COR = 2 FLAG ID = 7 FLAG VALUE = 0 
2.175