GTE Omni Scbs Installation And Maintenance Manual
Have a look at the manual GTE Omni Scbs Installation And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Fault Code Translation (Continued) Gull OMNi SBGS CIVIC-801 : FAULT DATA TRANSLATION 1. FAULT DATA IN HEX CODE: HH HH HH HH HH HH HH 1 234567 H: HEX CHARACTER O-9, A TO F OR BLANK 2. SCI STATUS EACH BIT SHOWS THE FOLLOWING MEANING: BBBBBBBB l- L !: L TRANSMITTER READY RECEIVER READY TRANSMITTER EMPTY PARITY ERROR OVER-RUN ERROR FRAMING ERROR BREAK DETECT DATA SET READY 3.28
DESCRIPTION 0 PLACE SMDR PRINTER OUT OF SERVICE WITH CMC-705 WHEN CHANGING PAPER. ENSURE THAT CORRECT RS-232-C PORT IS ENTERED. 0 CHANGE THE CONTROL CONDITION FOR THE MDR PRINTER REQUIREMENTS RELATING TO PAUSE TRANSMISSION CHARACTER, POWER CONTROL AND TIMING, OR PRINTOUT FORMAT pGGEGG-*I 1. PLACE PRINTER IN OR OUT OF SERVICE WITH CMC-705: CMC=705 0 PORT NUMBER (PI) P1:l P2:l 0 IN/OUT OF SERVICE FLAG (P2) 2. MODIFY PRINTER CONTROLS WITH CMC-901: .I 0 PORT NUMBER (PI) 0 PAUSE TRANSMISSION (XOFFIXON) CHARACTER (P2) CMC=901 0 POWER CONTROL (P3) P1:l P4: cl P2:l P5: 0 POWER ON TIMING (P5) P3: P6:l 0 POWER OFF TIMING (P6) * REFER TO OMNI SBCS GTEP MANUAL, MAINTENANCE SECTION, FOR DESCRIPTION OF ASCII &-ON/X-OFF AND POWER CONTROL CHARACTERS. 3.29
RS-232-C Port Configuration Assignkent GE awvll sms DESCRIPTION . ASSIGN OR MODIFY THE CHARACTERISTICS OF THE TWO RS-232-C PORTS INCLUDING BIT RATE, PARITY, CHARACTER LENGTH, STOP BIT AND ECHO. . BOTH PORTS ARE FULL DUPLEX. . DEFAULT STANDARD DATA BASE PRESENTS PORT jif FOR PMP AND PORT 1 FOR MDR PRINTER. piizGiq 1. USE CMC-900 TO SET RS-232-C PORT CHARACTERISTICS: . PORT (PI) . BIT RATE (P2) . PARITY (P3) l CHARACTER LENGTH (P4) . STOP BIT (P5) . ECHO BACK (P6) NOTE: IF PORT TO BE CHANGED IS ASSIGNED TO SMDR PRINTER, FIRST PLACE PRINTER OUT OF SERVICE WITH CMC-705. 3.30
Diagnostic Trunk Connection Assignment j-J 0 CMC-802 DED‘iCATES A TRUNK TO A DESIGNATED STATION FOR AUDITORY, RINGING, AND TRANSMISSION VERIFICATION. @ AFTER ASSIGNMENT, TESTS CAN BE MADE BY ORIGINATING A CALL TO THE TRUNK BY DIALING THE TRUNK ACCESS CODE FOR THE TRUNK GROUP. @ WORKING TRUNK CAN BE CONFIRMED BY DIALING AN OUTSIDE DIRECTORY NUMBER AND LISTENING FOR CONFIRMATION CALL PROGRESS TONES. 1 PROCEDURE +[ I I 1. USE CMC-802 TO ENTER STATION DIRECTORY NUMBER AND TRUNK TO BE TESTED: CMC=802 l DIRECTORY NUMBER (PI) l TRUNK EQUIPMENT NUMBER (P2) r-l P1:214 P2:181 NOTE: WHEN ACTlVATED STATION WILL ALWAYS SEIZE ASSIGNED TRUNK UNTIL VALUES FOR PI AND P2 ARE DELETED WITH REMOVE KEY. 3.31
. . . ,.- c Measuremen DESCRIPTION GE OMNI slxs . ASSIGN OR CANCEL TRUNK GROUP NUMBERS TO BE SAMPLED WlTH CMC-600. . ACTIVATE A TRAFFIC MEASUREMENT STUDY WITH CMC-601. @ DEFINE THE DISPLAY FOR TRAFFIC MEASUREMENT BASED ON RECENT DATA (LESS THAN IO HOURS) OR OLDER DATA (AFTER 10 HOURS). . TRAFFIC DENSITY PERCENTAGE IS DISPLAYED BASED ON DESIGNATED TRUNK GROUP NUMBERS. (PROCEDURE1 CMC=600 Pl:l 1. ASSIGN TRUNK GROUP NUMBERS TO BE SAMPLED WITH CMC-600: P2:13 . REGISTRATION SEQUENCE NUMBER: (PI) . TRUNK GROUP NUMBER (P2) 1 2. USE CMC-601 TO ACTIVATE TRAFFIC MEASUREMENT FLAG: @ TRAFFIC MEASUREMENT START/STOP FLAG (PI) CMC=601 3. USE CMC-602 TO DISPLAY TRAFFIC MEASUREMENT DATA: . TRAFFIC MEASUREMENT DATA AREA (PI) . REGISTRATION SEQUENCE NUMBER (P2) El Pi:1 @ TRUNK GROUP NUMBER (P3) . ELAPSED TIME IN HOURS (P4) CMC=602 . TRAFFIC DENSITY (P5) P1:2 P4:l NOTE: TRUNK GROUP NUMBERS MUST BE DELETED FROM SAMPLE WITH- REMOVE KEY AFTER TRAFFIC STUDY HAS BEENd El P2:l P5:O P3:13 DEACTIVACTIVATED (CMC-601). 3.32
aintenance Comman Gull TRUNK GROUP TRAFFIC SCREENING ASSIGNMENT TRAFFIC MEASUREMENT ACTIVATION TRAFFIC MEASUREMENT DATA DISPLAY TIME AND DATE SETTING CIRCUIT BUSY ASSIGNMENT SMDR IN/OUT OF SERVICE 600 ASSIGNS TRUNK GROUP NUMBERS TO TRAFFIC SAMPLE. 601 ACTIVATES TRAFFIC MEASUREMENT STUDY. 602 DISPLAYS TRAFFIC DENSITY. 700 701 705 SETS SYSTEM HARDWARE AND SOFTWARE CLOCK. PLACES CIRCUITS IN/OUT OF SERVICE FOR MAINTENANCE. PLACES SMDR IN/OUT OF SERVICE FOR MAINTENANCE. 3.33
c-. Maintenance Data Base Commands/ CM6 Command Summary (Continued) Gull awvn ~Bcs 0 0 e e 0 e 0 DEVICE STATUS 800 LISTS FAULTY DEVICES AND LOCATIONS. FAULT LOG 801 DIAGNOSTIC TRUNK CONNECTION ASSIGNMENT RS-232-C PORT CONFIGURATION SMDR PRINTER CONTROL READ OUT SYSTEM SOFTWARE VERSION ID DISPLAY DISTRIBUTED PROCESSOR VERSION ID DISPLAY 802 900 901 904 907 PROVIDES DETAILED FAULT INFORMATION FOR TROUBLESHOOTING. ASSIGNS A STATION TO A TRUNK FOR DIAGNOSTIC VERIFICATION. CHANGES CHARACTERISTICS OF RS-232-C PORTS. CHANGES CONTROL CONDITION FOR SMDR. DISPLAYS CURRENT SOFTWARE RELEASE. DISPLAYS VERSION NUMBER FOR ICG CARDS. 3.34
PERFORM THE FOLLOWING PROGRAMMING TASKS IN THE SEQUENCE OUTLINED BELOW AND IN ACCORDANCE WITH THE GTE OMNI SBCS MANUAL. COMPLETE THE REVIEW EXERCISE QUESTIONS UPON COMPLETION OF THIS LABORATORY ACTIVITY. Labo - Maintenance/Data WORK ORDER #3.2 ZOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-l 212 -0CATION: RESTON, VIRGINIA WORK ORDER 3.2 (TASK #l) IRIGINATOR: TELECOMMUNICATIONS MANAGER TASKS: 0 Set time, day, date with CMC-700. 0 Take a circuit out of service with CMC-701. 0 Display software and distributed processor version number with CMC-904 and CMC-907. (1) Set system clock using CMS-700. (1) Perform maintenance programming (2) Remove loop tie line circuit. (EN1 60) from commands. service with CMC-701. (2) Check/test the operation of commands after (3) Obtain current software version number with completion of this portion of the laboratory CMC-904 and CMC-907. (3) Proceed with next work order task. I
Laboratory Activity - Maintenance/Data Base Commands (3.2) (Continued) WORK ORDER #3.2 ZOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-1212 .OCATION: RESTON, VIRGINIA WORK ORDER 3.2 (TASK #2) IRIGINATOR: TELECOMMUNICATIONS MANAGER rASKS: l Restore circuit to service with CMC-701. l Display device status with CMC-800. l Display fault log with CMC-801. (1) Restore the loop tie line to service. (1) Perform maintenance programming commands. (2) Unplug one of the CS-10 telephones from its (2) Check/test the operation of commands after modular jack. completion of this portion of the laboratory activity. (3) Check the device status display with CMC-800. (3) Proceed with next work order task. / (4) Read out the latest fault log listing with CMC-801. Was equipment number of disconnected @S-10 telelphone displayed? 3.37