Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

							Speed Dial2-241
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit.
4. Pressbutton#21.ThedisplayupdatestoreflectcurrentprogrammingforPageC.
XXX-XXX = Station Range
5. Press the SPEED DIAL ACCESS button (FLASH 50, Page C, Button #6). The following
message displays:
6. Enter a range of speed bins to be allowed (100-999). The leading digit 9 is not reflected on
the LCD and is not used for your entry.
7. PressHOLDtosavetheentry.
Speed Bins/Chaining
Description
Speed dial bins can be chained together. This is helpful for accessing Long Distance carriers
or banking services when account codes are required.
Operation
To chain speed bins together, simply press one speed bin and then another as required.
Initialize System/Station Speed Numbers
Description
System and Station Speed bins may be initialized to reset all bins to their original default
value (empty). All bins 9000-9999 are reset to their default value (empty) upon initializing.
Programming Steps
1. Press the SPEED NO flexible button (FLASH 80, Button #6). The following message
displays:
2. Press the HOLD button. A confirmation tone sounds.
XXX-XXX PAGE C
ENTER BUTTON NUMBER
SYS SPEED BIN 100-999
###-###
INITIALIZE SYS SPEED NO
PRESS HOLD 
						

							2-242Speed Dial
Chapter 2 - Features and Operation
Print System Speed Numbers
Description
The System Speed Numbers command dumps the entire database as a permanent record
which can serve as a hardcopy of the database. The system baud rate must match that of the
printer or receiving device.
Figure 2-17: System Speed Numbers Printout
Programming Steps
1. Press the SYSTEM SPEED flexible button(FLASH 85, Button #6). The following message
displays:
2. To print the System Speed bins, press the HOLD button. The following message displays:
When the system finishes sending the requested information to the printer, a
confirmation tone sounds.
SYSTEM SPEED NUMBERS
20 37
21 38
22 39
23 40
24 41
25 42
26 43
27 44
28 45
29 46
30 47
31 48
32 49
33 50
34 51
35 52
36 ... and so on through Speed Number 999
PRINT SYS SPEED NO
PRESS HOLD
PRINTING SYS SPEED NO 
						

							Station Attributes2-243
Chapter 2 - Features and Operation
Station Attributes
Initialize Station Attributes
Description
The Station Parameters may be initialized setting all data fields to their original, default
values. The following data fields are returned to their default value upon initializing the
Station Attributes.
Table 2-20: Station Attribute Defaults
Program
CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
FLASH 50 1 Paging Access Enabled
PAGE A 2 Do Not Disturb Enabled
3 Conference Enable/Disable (Per Station) Enabled
4 Executive Override Disabled
5 Privacy (Per Station) Enabled
6 System Speed Dial Access Enabled
7 Line Queuing Enabled
8 Preferred Line Answer Enabled
9 Off-Hook Voice Over (OHVO) Disabled
10 Call Forwarding Enabled
11 Forced Least Cost Routing (LCR) Disabled
12 ACD Supervisor Monitor with Barge-In Disabled
13 Executive Override Blocking Disabled
14 CO Line Ringing Options Muted Ring
15 Name/Number Display at Idle Name (Enabled)
16 ACD Zap Tone Disabled
17 CO, Loop, Pool Disabled
18 Admin Access Disabled 
						

							2-244Station Attributes
Chapter 2 - Features and Operation
Programming Steps
1. Press the STATION ATTRIBUTES flexible button (FLASH 80, Button #3). The following
message displays:
2. Press the HOLD button. A confirmation tone sounds.
FLASH 50
PA G E B1 Station Identification 006 (24-Btn Keyset)
6(SLTw/oMW)
2 Station Day Class of Service (COS) COS 1
3 Station Night Class of Service (COS) COS 1
4 Speakerphone/Headset Programming 0=Full Speakerphone
5 Pick-Up Group(s) Programming Group 1
6 Paging Zone(s) Programming Zone 1
8 Line Group Access - Station Group 1
9 LCR Class of Service (COS) 0 (Unrestricted Access)
10 Off-Hook Preference Programming 00=No specific button
preferred; Enabled
11 Flexible Button Programming (blank)
12 Keyset Mode Inactive Mode
13 Voice Mail ID Translation XXXX=Station #
14 Display Flexible Buttons None
17 Cordless Key Telephone Unit (CKTU) Button 00=No button assigned
FLASH 50
PA G E C1 Internal No Answer Forward None
2 Internal Busy Forward None
3 External No Answer Forward None
4 External Busy Forward None
5 No Answer Timer 10 sec
6 Speed Dial Access None
INITIALIZE STATIONS
PRESS HOLD
Table 2-20: Station Attribute Defaults
Program
CodeFlexible
ButtonFeaturesDefault Value
(after initialization) 
						

							Station Attributes2-245
Chapter 2 - Features and Operation
Print Station Attributes
Description
The Print Station Attributes command dumps the entire database as a permanent record
which can serve as a hardcopy of the database. The system baud rate must match that of the
printer or receiving device.
When printing the Station attributes the following data prints:
>>>All Current Station Parameters
Figure 2-18: Station Attributes Printout
STATION ATTRIBUTES
STA 100 STA 101
PAGE ACCESS ENABLED PAGE ACCESS ENABLED
DO NOT DISTURB ENABLED DO NOT DISTURB ENABLED
CONFERENCE ENABLED CONFERENCE ENABLED
EXEC OVERRIDE DISABLED EXEC OVERRIDE DISABLED
PRIVACY ENABLED PRIVACY ENABLED
SYSTEM SPEED ENABLED SYSTEM SPEED ENABLED
LINE QUEUING ENABLED LINE QUEUING ENABLED
PREF LINE ANSWER DISABLED PREF LINE ANSWER DISABLED
OFF HOOK VOICE OVER DISABLED OFF HOOK VOICE OVER DISABLED
CALL FORWARD ENABLED CALL FORWARD ENABLED
FORCE LCR DISABLED FORCE LCR DISABLED
ACD SUPV BARGE IN DISABLED ACD SUPV BARGE IN DISABLED
EXEC OVERRIDE BLOCK DISABLED EXEC OVERRIDE BLOCK DISABLED
CO RING OPTIONS MUTED RING CO RING OPTIONS MUTED RING
NAME AT IDLE LCD EXT NUMBER NAME AT IDLE LCD EXT NUMBER
ACD ZAP TONE DISABLED ACD ZAP TONE DISABLED
STATION ID KEYSET - SP 24BTN STATION ID KEYSET - SP 24BTN
CO LOOP POOL FLEX DISABLED CO LOOP POOL FLEX DISABLED
DAY COS 1 DAY COS 1
NIGHT COS 1 NIGHT COS 1
SPEAKERPHONE  FULL SPEAKERPHONE SPEAKERPHONE FULL SPEAKERPHONE
PICKUP GROUPS 1 PICKUP GROUPS 1
PAGE ZONE 1 PAGE ZONE 1
INTERNAL NO ANSWER ### INTERNAL NO ANSWER ###
INTERNAL BUSY ### INTERNAL BUSY ###
EXTERNAL NO ANSWER ### EXTERNAL NO ANSWER ###
EXTERNAL BUSY ### EXTERNAL BUSY ###
NO ANSWER TIMER 10 NO ANSWER TIMER 10
LINE GROUP ACCESS 1 LINE GROUP ACCESS 1
LCR CLASS OF SERVICE 0 LCR CLASS OF SERVICE 0
OFFHOOK PREFENCE BTN 00 ENABLED OFFHOOK PREFENCE BTN 00 ENABLED
KEYSET MODE INACTIVE MODE 2400 KEYSET MODE INACTIVE MODE 2400
VOICE MAIL ID 100 VOICE MAIL ID 101
CORDLESS KEY BTN 00 LIGHT CONTROL NONE
BUTTONS: DISPLAY LCD MSG NONE
01D100 02D101 03D102 CORDLESS KEY BTN 00
04D103 05D104 06D105 BUTTONS:
07D106 08D107 09D108 01100 02D101 03D102
10D109 11D110 12D111 04D10 05C001 06C002
13L001 14C002 15L003 07LP 08PL1 09CBK
16L004 17L005 18L006 10PKU 11DND 12LQU
19LP 20PL1 21CBK 13L001 14C002 15L003
22PKU 23DND 24LQU 16L004 17L005 18L006
25FLA 26XFR 27SPD 19LP 20PL1 21CBK
28CNF 29MSG 30FWD 22PKU 23DND 24LQU
31MUT 32CPO 33MON
34HLD 35VOL 36VOL ... and so on through all stations
NOTE: The button printout for the 8-button keyset displays all flexible AND fixed buttons, the same as the 24-button keyset. 
						

							2-246Station Identification
Chapter 2 - Features and Operation
Programming Steps
1. Press the STATION ATTRIBUTES flexible button(FLASH 85, Button #3). The following
message displays:
2. To print data for:

						

							Station Identification2-247
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit.
4. Pressbutton#20.ThedisplayupdatestoreflectcurrentprogrammingforPageB.
XXX-XXX = Station Range
5. Press the STATION ID flexible button(FLASH 50, Page B, Button #1).
6. Enter a valid number on the dial pad to identify type of telephone:
7. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT…All Key Telephone Boards (DTIB) default to ID 006 (24-Button Digital Telephone),
all Single Line Boards (SLIB) default to ID 6.
Station ID Lock
Description
The Station ID Lock feature provides a means for the installer/programmer to lock the station
ID of all stations in the system. After locked, attempts to plug unlike devices (e.g., a DSS into a
24-button port) results in the device not working. This feature is designed to prevent loss of
station programming that results when a different station type is plugged into a port already
designated as another station type.
To change the Station ID with the Station ID Lock feature enabled:
1. Enter programming mode and disable the Station ID Lock feature.
2. Plug the new device type into the jack. The set is automatically identified.
3. Enter programming and perform Station ID programming (FLASH 50, Page B, Button #1).
Set is automatically identified.
4. Enter programming mode and enable the Station ID Lock feature.
XXX - XXX PAGE B
ENTER BUTTON NUMBER
STATION ID 0-8
KEYSET -SP24BTN
[1-5] = DSS Console [007] = 12-Btn Phone
[6] = SLT w/o Msg Wait [008] = 8-Btn Phone
[7] = SLT w/Msg Wait (90 VDC) [015] = SLA
[006] = 24-Btn Phone [016] = Lg Disp 30-Btn Phone 
						

							2-248 Station Message Detail Recording
Chapter 2 - Features and Operation
Programming Steps
1. PresstheSTATIONIDLOCKflexiblebutton(FLASH 06, Button #8). The following
message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable the use of this feature.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT…Station ID Lock feature is disabled.
Station Message Detail Recording
Description
TheXTSstation message detail recording (SMDR) provides details on both incoming and
outgoing calls. This feature is programmable to allow recording of all calls or just outgoing
long distance calls. The system tracks calls by outside line, number dialed, time-of-day, date,
station that placed the call and duration of call. Account codes may also be entered and
recorded.
The SMDR Qualification Timer determines the length of time that is needed to determine a
valid SMDR call for reporting purposes. By default, this timer is set to 30 seconds and is
variable from 00 to 60 seconds in 1-second increments.
This feature is enabled or disabled in system programming. By default, SMDR is not enabled
and is set to record long distance calls only. A printout format of 80 characters maximum or
30 characters maximum may be selected in system programming. The standard format is
80 characters on a single line. A 30 character format generates 3 lines per message. If the
SMDR feature is enabled, the system starts collecting information about the call as soon as it
starts and terminates when the call ends. If the call was longer then 30 seconds, the following
information is printed:
STATION LOCK 0-1
DISABLED 
						

							Station Message Detail Recording 2-249
Chapter 2 - Features and Operation
Figure 2-19: SMDR Printout
80 character format - Outbound Call to a Dialed Number:
12345678
12345678901234567890123456789012345678901234567890123456789012345678901234567890
AAAA BBB HH:MM:SS HH:MM MM/DD/YY HCCCCCCCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)
STA   CO TOTAL    START   DATE   DIALED
1100 001 00:00:38 13:57 01/15/01 O2956006
80 character format - Outbound Call to an Extension:
12345678
12345678901234567890123456789012345678901234567890123456789012345678901234567890
AAAA BBB HH:MM:SS HH:MM MM/DD/YY HCCCCCCCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)
STA   CO TOTAL    START   DATE   DIALED
1100 031 00:00:08 13:58 01/15/01 O2108 **
  **CALL TO HOWARD
80 character format - Outbound Call to an Extension:
12345678
12345678901234567890123456789012345678901234567890123456789012345678901234567890
AAAA BBB HH:MM:SS HH:MM MM/DD/YY HCCCCCCCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)
STA   CO TOTAL    START   DATE   DIALED
1102 031 00:00:11 13:59 01/15/01 O2101 **
  **CALL TO STA2101
80 character format - Inbound Call from an Extension:
12345678
12345678901234567890123456789012345678901234567890123456789012345678901234567890
AAAA BBB HH:MM:SS HH:MM MM/DD/YY HCCCCCCCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)
STA   CO TOTAL    START   DATE   DIALED
1100 031 00:00:03 13:59 01/15/01 I2108 **
  **HOWARD CALLING - continued on next page -
80 character format - Inbound Call to a Station From CO Line 1 with No Caller ID:
12345678
12345678901234567890123456789012345678901234567890123456789012345678901234567890
AAAA BBB HH:MM:SS HH:MM MM/DD/YY HCCCCCCCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)
STA   CO TOTAL    START   DATE   DIALED
1100 001 00:00:04 13:59 01/15/01 I
LEGEND:
- AAAA = Station originator or Trunk on DISA and Off-Net (CO Line) calls.
- BBB  = Outside line number
- HH:MM:SS = Duration of call in Hours, Minutes and Seconds
- HH:MM = Time of day (start time) in Hours and Minutes
- MM/DD/YY = Date of Call
- H = Indicates call type:
“I” = Incoming*
“O” = Outgoing
“T” = Transferred*
“U” = Unanswered calls for ICLID SMDR call records
- CC....CC = Number dialed
- GG....GG = Last Account code entered (optional)
- (CR) = Carriage return
- (LF) = Line Feed 
						

							2-250 Station Message Detail Recording
Chapter 2 - Features and Operation
TheXTSsystem can provide SMDR output to the optional RS-232C connectors on the MISB.
When SMDR is desired, the following system-wide parameters determine how SMDR
information is reported.
Programming Steps
1. PressFLASHand dial[21]. The following message displays:
2. To program SMDR features, use the flexible button(s) as defined in the following
procedures.
3. The ENABLE/DISABLE, TYPE, and PRINT features toggle on and off each time the button is
pressed. The display updates with each toggle.
4. After all entries are made, press HOLD to save the entry. A confirmation tone sounds.
SMDR Enable / Disable
Description
A call accounting device can be installed allowing the system to track calls by outside line
number, number dialed, time of day, date, station that placed or received the call, and
duration of the call.
Programming Steps
1. Press the ENABLE/DISABLE flexible button(FLASH 21, Button #1). This feature toggles
on and off each time the button is pressed. The display updates with each toggle.
LED ON = SMDR is enabled
LED OFF = SMDR is disabled
2. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT…SMDR is disabled.
ENABLE / DISABLECALL TYPEPRINT FORMAT
✺1Q✺2W✺3E✺4R
PORT
✺5T✺6Y✺7U✺8I
SDR TPE PNT BAUD PORT
NO LD 80 19.2K 1