Home > Triad > Telephone > Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 9 Triad manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 626
    							CO Line - Loop Supervision2-81
    Chapter 2 - Features and Operation
    CO Line - Loop Supervision
    Description
    TheXTScan be programmed to monitor CO lines while on-hold or connected to RAN devices
    or Voice Mail systems, or in Trunk-to-Trunk connections for disconnect signal provided by the
    Telco. After a disconnect signal is detected, theXTSreleases the CO lines and automatically
    place them back in service.
    Loop Supervision Programming
    Description
    Loop Supervision is used primarily with DISA, Voice Mail/Auto Attendant and with
    unsupervised conference applications. It lets the system detect when loop current is broken
    and an outside line is no longer being used. To determine timer value for loop supervision,
    consult your local central office for type and duration of loop supervision signal.
    Programming Steps
    1. PressFLASHand dial[40]. The following message displays:
    2. Enter a valid number for the range of lines being programmed. If only one line is being
    programmed, enter that number twice (001 001).
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    Flexible button #19 (Page A) is lit. The following message displays to indicate current
    programming of that line or group of lines:
    XXX-XXX = CO Line Range
    4. Press the LOOP SUPV flexible button(FLASH 40, Page A, Button #6).
    5. Enter a valid number (1-9) on the dial pad which corresponds to 100-900 ms.
    (0 = disabled).
    6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    DEFAULT…Loop Supervision is set for 400 ms for all CO Lines.
    CO LINE ATTRIBUTES
    SELECT A CO LINE RANGE
    If HOLD is pressed without entering a CO range, ALL CO lines are selected.
    XXX - XXX PAGE A
    ENTERBUTTONNUMBER
    LOOP SUPERVISION 0-9
    4 
    						
    							2-82CO Line - Queue
    Chapter 2 - Features and Operation
    CO Line - Queue
    Description
    When all outside lines in a group are busy, stations can be placed in queue awaiting a line in
    the same group to become available. If a station doesn’t answer the queue signal within
    15 seconds, that station is dropped from the queue. A station can queue only one line at a
    time.
    Line Queuing
    Description
    Stations can be allowed or denied the ability to manually queue for a busy group of CO lines.
    Even when disabled, stations have automatic LCR queuing privileges.
    Programming Steps
    1. PressFLASHand dial[50]. Flexible button #24 (New Range) is lit and the following
    message displays:
    2. Enter the range of station numbers to be programmed. If only one station is being
    programmed, enter that number twice (100 100).
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    Flexible button #19 is lit. The display updates to reflect current programming for Page A:
    XXX-XXX = Station Range
    4. Press the QUEUING flexible button(FLASH 50, Page A, Button #7). The following
    message displays:
    5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
    [0] = Disabled
    [1] = Enabled
    STATION ATTRIBUTES
    SELECT A STATION RANGE
    If HOLD is pressed without entering a station range, ALL stations are selected.
    XXX - XXX PAGE A
    ENTER BUTTON NUMBER
    LINE QUEUING 0-1
    ENABLED 
    						
    							CO Line - Queue2-83
    Chapter 2 - Features and Operation
    6. Press HOLD to save the entry. A confirmation tone sounds.
    DEFAULT…CO Line Queuing is enabled at all stations.
    Operation
    If you see that a particular outside line is busy and you wish to be placed on a list
    waiting for that line to become available:
    1. Press desired busy OUTSIDE LINE button,
    -or-
    Press the POOL button. (Busy tone sounds.)
    2. Press the preprogrammed CO LINE QUEUE button (621).
    3. Replace handset or press ON/OFF button.
    To answer a queue:
    If you hear ringing and an outside line of the line group or a LOOP button you queued onto is
    rapidly flashing:
    1. Lift handset or press ON/OFF button.
    2. Press flashing OUTSIDE LINE button or LOOP button to answer.
     SINGLE LINE TELEPHONE
    1. Dial outside line access code. Receive busy tone.
    2. Briefly depress and release the hookswitch.
    3. Dial [621]. Confirmation tone sounds.
    Conditions
    »A LOOP button or direct appearance of the queued line is required.
    CO Line Queue Button Flash Rate
    Description
    The Line Queue Button flash rate is the rate at which the Line Queue button flashes after
    queueing onto a busy line. This button flashes when the busy line becomes available. This
    flash rate can be programmed to 29 different options identified in the flash rate table which
    enables the programmer to customize the key system configuration to desired flash rates.
    Programming Steps
    1. Press the LINE QUEUE BTN flexible button(FLASH 07, Button #17).
    2. Enter a valid number (00-28) on the dial pad to correspond to one of the 29 available
    options. (Refer toTable 2-13 on page 2-137.)
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    DEFAULT…Line Queue Button flash rate is set for a Red 480 ipm Flutter (08).
    LINE QUEUE BTN 00-28
    RED 480 IPM FLUTTER 
    						
    							2-84CO Line - Ringing Options
    Chapter 2 - Features and Operation
    CO Line - Ringing Options
    Description
    When a CO call rings at a busy station, the call rings at the station using a muted ring signal.
    This option allows a user to receive a reminder ring at their busy station, instead of muted
    ringing. A reminder ring timer is also available to provide the reminder ring every time the
    timer expires, as long as the incoming CO line remains connected.
    Programming Steps
    1. PressFLASHand dial[50]. Flexible button #24 (New Range) is lit and the following
    message displays:
    2. Enter the range of station numbers to be programmed. If only one station is being
    programmed, enter that number twice (100 100).
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    Flexible button #19 is lit. The display updates to reflect current programming for Page A:
    XXX-XXX = Station Range
    4. Press the RINGING OPTIONS flexible button(FLASH50,PageA,Button#14).The
    following message displays:
    5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
    [0] = Reminder Ring
    [1] = Muted Ring
    6. Press HOLD to save the entry. A confirmation tone sounds.
    DEFAULT…Muted Ringing is allowed at all stations.
    STATION ATTRIBUTES
    SELECT A STATION RANGE
    If HOLD is pressed without entering a station range, ALL stations are selected.
    XXX - XXX PAGE A
    ENTER BUTTON NUMBER
    CO RING OPTIONS 0-1
    MUTED RING 
    						
    							CO Line - Ringing Options2-85
    Chapter 2 - Features and Operation
    Transfer CO Ringing
    Description
    The Transfer CO Ringing flash rate is the rate at which a CO Line button or Loop button
    flashes when a call is transferred to you. This flash rate can be programmed to 29 different
    options identified in the flash rate table. This enables the programmer to customize the key
    system configuration to desired flash rates.
    Programming Steps
    1. Press the TRANSFER CO RING flexible button(FLASH 07, Button #9). The following
    message displays:
    2. Enter a valid number (00-28) on the dial pad to correspond to one of the 29 available
    options. (Refer toTable 2-13 on page 2-137.)
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    DEFAULT…Transfer CO Ringing flash rate is set for a Red 120 ipm Flash (10).
    Recall CO Ringing
    Description
    The Recall CO Ringing flash rate is the rate at which a CO Line button or Loop button flashes
    when a call recalls to your station. This flash rate can be programmed to 29 different options
    identified in the flash rate table. This enables the programmer to customize the key system
    configuration to desired flash rates.
    Programming Steps
    1. Press the RECALL CO RING flexible button(FLASH 07, Button #10). The following
    message displays:
    2. Enter a valid number on the dial pad to correspond to one of the 29 available options.
    (Refer toTable 2-13 on page 2-137.)
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    DEFAULT…Recall CO Ringing flash rate is set for a Red 480 ipm Flutter (08).
    TRANSFER CO RING 00-28
    RED 120 IPM FLASH
    RECALL CO RING 00-28
    RED 480 IPM FLUTTER 
    						
    							2-86CO Line - Ringing Options
    Chapter 2 - Features and Operation
    Queued CO Ringing Flash Rate
    Description
    The Queued CO Ringing flash rate is the rate at which a CO Line button or Loop button
    flashes when a queued line becomes available. This flash rate can be programmed to
    29 different options identified in the flash rate table. This enables the programmer to
    customize the key system configuration to desired flash rates.
    Programming Steps
    1. Press the QUEUED CO RING flexible button(FLASH 07, Button #11). The following
    message displays:
    2. Enter a valid number (00-28) on the dial pad to correspond to one of the 29 available
    options. (Refer toTable 2-13 on page 2-137.)
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    DEFAULT…Queued CO Ringing flash rate is set for a Green 480 ipm Flutter (22).
    Reminder Ring Timer
    Description
    When a CO line rings at a busy station, the call rings at the station using muted ringing. The
    CO Line Ringing Option feature enables a user to receive a reminder ring instead of muted
    ring. This timer provides a reminder ring every time the timer expires, as long as the incoming
    CO line remains connected.
    If the user continues their present conversation and the CO party does not hang up, the
    Reminder Ring timer expires and the user receives another ring burst. When the key set user
    ends the existing call, ringing for the CO call reverts to normal ringing.
    The Reminder Ring Timer setting is variable from 00-99 seconds in 1-second increments.
    Programming Steps
    1. Press the REMINDER RING flexible button(FLASH 01, Button #18). The following
    message displays:
    2. Enter a valid number on the dial pad that corresponds to 00-99 seconds in 1-second
    increments. A value of 00 disables the timer, therefore the user only receives one ring
    burst at the beginning of the call.
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    DEFAULT…Reminder Ring Timer is set to 00 second.
    QUEUED CO RING 00-28
    GREEN 480 IPM FLUTTER
    REMINDER RING 00-99
    00 
    						
    							CO Line - Ringing Options2-87
    Chapter 2 - Features and Operation
    CO Direction
    Description
    CO Lines can be programmed on a per CO Line basis for the type of CO Line desired:
    Incoming
    
    						
    							2-88CO Port Parameters
    Chapter 2 - Features and Operation
    5. Enter a valid number (0-3) on the dial pad which corresponds to the desired CO type:
    [0] = Out-of-Service (OOS)
    [1] = Incoming Only
    [2] = Outgoing Only
    [3] = Both Incoming and Outgoing
    6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    DEFAULT…All CO Lines default to both incoming and outgoing type.
    Conditions
    »For PRI cards, the 24th channel mustbe marked as Out-of-Service (OOS). This is true on all
    PRI cards, not just for networking.
    CO Port Parameters
    Initialize CO Port Assignments / Flexible Numbering Assignments
    Description
    CO Port Parameters and Flexible Numbering Assignments can be initialized to default values
    as shown in“FLASH 42”on page E-18and“FLASH 52”on page E-21,bothwithinTa b l e E - 1.
    Programming Steps
    1. Press the CO PORTS/COD flexible button (FLASH 80, Button #4).
    2. The following message displays:
    3. Press the HOLD button. A confirmation tone sounds.
    INITIALIZE CO PORTS/COD
    PRESS HOLD 
    						
    							CO Port Parameters2-89
    Chapter 2 - Features and Operation
    PrintCOPortParametersandFeatureCodes
    Description
    The Print CO Port Parameters and Feature Codes command dumps the entire database as a
    permanent record which can serve as a hardcopy of the database. The system baud rate must
    match that of the printer or receiving device.
    Figure 2-4: CO Port Attributes Printout
    Programming Steps
    1. Press the CO PORT flexible button(FLASH 85, Button #4). The following message
    displays:
    2. To print the CO Port Parameters and Feature Codes, press the HOLD button. The following
    message displays:
    When the system finishes sending the requested information to the printer, a
    confirmation tone sounds.
    CO PORT NUMBERS
    01
    02
    03
    04
    05
    06
    07
    08
    09
    10
    11
    12
    13
    14
    15
    16
    17
    18-
    -
    -
    -
    -
    -
    -
    -
    -
    -
    -
    -
    -
    -
    -
    -
    -
    -01
    09
    17
    25
    33
    41
    49
    57
    65
    73
    81
    89
    97
    105
    113
    121
    129
    13702
    10
    18
    26
    34
    42
    50
    58
    66
    74
    82
    90
    98
    106
    114
    122
    130
    13803
    11
    19
    27
    35
    43
    51
    59
    67
    75
    83
    91
    99
    107
    115
    123
    131
    13904
    12
    20
    28
    36
    44
    52
    60
    68
    76
    84
    92
    100
    108
    116
    124
    132
    14005
    13
    21
    29
    37
    45
    53
    61
    69
    77
    85
    93
    101
    109
    117
    125
    133
    14106
    14
    22
    30
    38
    46
    54
    62
    70
    78
    86
    94
    102
    110
    118
    126
    134
    14207
    15
    23
    31
    39
    47
    55
    63
    71
    79
    87
    95
    103
    111
    119
    127
    135
    14308
    16
    24
    32
    40
    48
    56
    64
    72
    80
    88
    96
    104
    112
    120
    128
    136
    144
    PRINT CO PORTS/CODES
    PRESS HOLD
    PRINTING CO PORT 
    						
    							2-90CO Ring Detect Timer
    Chapter 2 - Features and Operation
    CO Ring Detect Timer
    Description
    The CO Ring Detect Timer controls the time necessary to detect an outside line ringing into
    the system. The duration of the ringing signal from the CO or the PBX is matched with ringing
    detection circuitry in theXTS. The ring detect can range from 200 ms to 900 ms programmed
    in 100 ms increments. This timer helps prevent false ringing.
    Programming Steps
    1. Press the CO RING DETECT TIMER flexible button(FLASH 01, Button #11). The following
    message displays:
    2. Enter a valid number on the dial pad that corresponds to 2-9 (200 ms to 900 ms).
    3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
    DEFAULT…CO Ring Detect Timer is set at 3 (300 ms).
    Conference
    Description
    The two types of conferencing are the multi-party conference and the unsupervised
    conference.
    Multi-party conference - can include up to eight parties. A maximum of five external parties
    can be conferenced.
    Unsupervised Conference - the conference initiator can exit a conference with two outside
    parties and leave them in an unsupervised conference. The initiator can re-enter the
    conference at any time. TheXTScan automatically terminate the call when both parties hang
    up, when Loop Supervision is provided by the Telco and enabled in the database. A
    programmable conference timer disconnects the unsupervised conference if the initiator
    does not re-enter.
    CO RING DETECT 2-9
    3 
    						
    All Triad manuals Comments (0)