Kyocera TASKalfa 250ci User Manual

							Default Setting (System Menu) 
OPERATION GUIDE8-97
8
HTTP Security Setup
Select the HTTP security level. This setup is available when SSL is On . The default setting is  HTTPS Only.
NOTE: HTTP must be set to [On] in  Protocol Detail on page 8-92.
Use the procedure below.
1Press the  System Menu  key.
2Press [System], [Next] of  Network, [Next] of  Secure 
Protocol , and then [Change] of HTTPS Security .
3Press [HTTP or HTTPS Only] or [HTTPS Only].
4Press [OK].
5After changing the setting, restart the system or 
turn the machine OFF and then ON again. 
For detailed information on restarting the system, 
refer to Restarting the System on page 8-88 .
LDAP Security Setup
Select the type of encryption according to the type of  security employed by the LDAP server. This setup is 
available when  SSL is On . The default setting is  Off.
NOTE: LDAP must be set to [On] in  Protocol Detail on page 8-92.
The table below shows the available settings.
Use the procedure below.
1Press the  System Menu  key.
2Press [System], [Next] of  Network, [Next] of  Secure 
Protocol , and then [Change] of LDAP Security .
3Press [Off], [LDAP over SSL] or [LDAPv3/TLS].
4Press [OK].
Item Description
Off Do not use security employed by the LDAP server.
LDAP over SSL Use implicit mode for data commu nication. The server provides services 
using the LDAP over SSL port (636). Encryption is applied to any data 
communication using this port.
LDAPv3/TLS Use explicit mode for data communic ation. Select this if the server supports 
the start TLS command. This uses the same port (389) as LDAP.
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
8-98OPERATION GUIDE
5After changing the setting, restart the system or 
turn the machine OFF and then ON again. 
For detailed information on restarting the system, 
refer to Restarting the System on page 8-88 .
IPSec Setting
Sets up IPSec. The default setting is  Off. Use the procedure below.
1Press the  System Menu  key.
2Press [System], [Next] of  Network Security, and 
then [Change] of  IPSec.
NOTE: If user login administration is disabled, the 
user authentication screen appears. Enter your login 
user name and password and then press [Login]. For 
this, you need to login wit h administrator privileges. 
Refer to  Adding a User on page 11-4  for the default 
login user name and password.
3Press [On].
4Press [OK].
5After changing the setting, restart the system or 
turn the machine OFF and then ON again. 
For detailed information on restarting the system, 
refer to Restarting the System on page 8-88 .
LAN Interface Setup
Specify the settings for the LAN interface to be used. The default setting is  Auto. Use the procedure below.
1Press the  System Menu  key.
2Press [System], [Next] of  Network and then 
[Change] of  LAN Interface .
3Select [Auto], [10BASE- T Half], [10BASE-T Full], 
[100BASE-TX Half] or [100 BASE-TX Full] as the 
LAN interface.System - LAN Interface
Select the LAN Interface type.
10BASE-T
Half
Auto
10BASE-T
Full100BASE-TX
Half 100BASE-TX
Full
Status
10/10/2008    10:10Cancel
OK
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
OPERATION GUIDE8-99
8
4Press [OK].
5After changing the setting, restart the system or 
turn the machine OFF and then ON again. 
For detailed information on restarting the system, 
refer to Restarting the System on page 8-88 .
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
8-100OPERATION GUIDE
Interface Block Setting
This allows you to protect this machine by blocking the interface with external devices such as USB hosts or 
optional interfaces. 
The following interface block settings are available:
• USB Host (USB memory slot setting)
• USB Device (USB interface setting)
• Optional interface (Optional interface card setting)
USB Host (USB memory slot setting)
This locks and protects the USB memory slot (A1) or USB port (A2) (USB host). The default setting is Unblock.
Use the procedure below to specify the USB Host setting.
1Press the  System Menu  key.
2Press [System], [Next] of  Interface Block Setting 
and then [Change] of  USB Host.
NOTE: If user login administration is disabled, the 
user authentication screen appears. Enter your login 
user name and password and then press [Login]. For 
this, you need to login wit h administrator privileges. 
Refer to  Adding a User on page 11-4  for the default 
login user name and password.
3Press [Block].
4Press [OK].
USB Device (USB interface setting)
This locks and protects the USB interface connect or (B1) (USB Device). The default setting is Unblock.
Use the procedure below to specify the USB Device setting.
1Press the  System Menu  key.
2Press [System], [Next] of  Interface Block Setting 
and then [Change] of  USB Device.
3Press [Block].
4Press [OK].
Optional interface (Optiona l interface card setting)
This locks and protects the optional interface  slots (OPT1 or OPT2). The default setting is Unblock.
Use the procedure below to specif y the optional interface setting.
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
OPERATION GUIDE8-101
8
1Press the System Menu  key.
2Press [System], [Next] of  Interface Block Setting 
and then [Change] of  Optional Interface 1 or 
Optional Interface 2 .
3Press [Block].
4Press [OK].
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
8-102OPERATION GUIDE
Security Level (Security Level setting)
The Security Level setting is primarily a menu option used by service personnel for maintenance work. There is 
no need for customers to use this menu.
Document Guard Setting
When the optional Printed Document Gu ard Kit is installed, the machine prevents the unauthorized copying and/
or transmission of documents that contain  important confidential or personal information.
Use the Security Watermark of Advanced in KX DRIVER to embed the guard pattern in a document. (Refer to 
the  Printer Driver User Guide  for details.)
We suggest you to confirm how the machine performs this function on your environment.
Machine Operation after Detecting the Document Guard Pattern
Item Description
Common operation Displays the message that indicates the machine detected the document  guard pattern and stops scanning the remaining documents.
Copy functions Prints the documents in blank fr om the position that the machine detected 
the document guard pattern.
Document Box functions Does not store the documents in the hard disk
Send functions Cancels the job.*
* Sends the documents that are scanned before the  document guard pattern is detected if you have 
selected File Separation. If not, every documents will not to be sent.
FAX functions  Does not send the documents.
Print the guard 
pattern using KX 
DRIVER.
copy
Canceled.
send 
or fax
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
OPERATION GUIDE8-103
8
Limitations:
- Scanning speed will be limited  to the speed of scanning 600 dpi image. (Printing speed will not 
be limited.)
- FAX transmission will be limited to the memory transmission.
Note: - The Printed Document Guard Kit should not fully prevents a leak of information. We do not guarantee any loss incurred while using this feature or when malfunction occurred with this 
feature.
- The guard pattern printed on the colored paper or paper that is decorated with special design  may not be detected.
- We do not guarantee the integrity  of the detection. If the malfunction occurs, contact your service 
representative.
Use the procedure below to specify the Document Guard setting.
1Press the  System Menu  key.
2Press [System] and then [Next] of  Optional 
Function .
NOTE: If user login administration is disabled, the 
user authentication screen appears. Enter your login 
user name and password and then press [Login]. For 
this, you need to login wit h administrator privileges. 
Refer to  Adding a User on page 11-4  for the default 
login user name and password.
3Select [Document Guard] from the list and then 
[License On].
4Enter the license key and press [Official]. To use 
the function as a trial, pr ess [Trial] without entering 
the license key.
NOTE: For details on how to enter the license key, 
consult your dealer or service representative.
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
8-104OPERATION GUIDE
Optional Functions
You can use the optional applications installed on this machine.
Overview of the Applications
The applications listed below are installed on this machine. 
You can use these applications for  a limited period on a trial basis.
• Printed Document Guard Kit
This prevents the unauthorized copying an d/or transmission of documents that contain important confidential or 
personal information. When a document is printed from a computer, this feature imprints a special pattern on 
the document. When anyone attempts to copy or send t hat document on this machine, the machine detects the 
pattern and protects the information by printing  the document in blank, prohibiting transmission.
NOTE: Restrictions such as the number of times the applic ation can be used during the trial period differ 
depending on the application.
Starting Application Use
Use the procedure below to start using an application.
1Press the System Menu  key.
2Press [System] and then [Next] of  Optional 
Function .
NOTE: If user login administration is disabled, the 
user authentication screen appears. Enter your login 
user name and password and then press [Login]. For 
this, you need to login wit h administrator privileges. 
Refer to  Adding a User on page 11-4  for the default 
login user name and password.
3Select the desired application and press [License 
On]. 
You can view detailed information on the selected 
application by pressing [Detail].System - Optional Function
Manage the optional functions.
Name
1/1
Activating
Detail
Status 10/10/2008    10:10
Print
ReportLicense
Close
Application 1
Application 2
Stopped
Application 3 Stopped
License
On
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
OPERATION GUIDE8-105
8
4In the license key entry screen, press [Official]. 
Some applications do not require you to enter an 
license key. If the license key entry screen does not 
appear, go to Step 5.
To use the application as a trial, press [Trial] without 
entering the license key.
5When the confirmation screen appears, press 
[Yes].
IMPORTANT: If you change the date/time while using 
an application, you will no l onger be able to use the 
application.
Checking Application Details
Use the procedure below to check the details of an application.
1Press the System Menu  key.
2Press [System] and then [Next] of  Optional 
Function .
NOTE: If user login administration is disabled, the 
user authentication screen appears. Enter your login 
user name and password and then press [Login]. For 
this, you need to login wit h administrator privileges. 
Refer to  Adding a User on page 11-4  for the default 
login user name and password.
3Select the application you want to check the details 
of and press [Detail]. 
You can now view detailed information on the 
selected application.
License On
Enter the activation code to use the application officially.
The activation code is not necessary to use it as a trial.
Status 10/10/2008    10:10
Official
Activation
Code
********
Trial
Cancel
Downloaded From ManualsPrinter.com Manuals 
						

							Default Setting (System Menu) 
8-106OPERATION GUIDE
Accessibility (Enlarged Touch Panel Display) 
Touch panel characters and key displays can be enlarged. Use the numeric keys to select items and proceed 
to the next screen.
NOTE: Accessibility can be used only wi th Copying and Sending registered on the Quick Setup screen. 
To set functions othe r than those displayed in the a ccessibility screens, you must retu rn to the original display. 
Press the Accessibility Display  key again.
Press the Accessibility  Display  key when in the Copy 
or Send (i.e. the  Copy or Send key indicator is On).
Enlarged keys or characters  appear on the touch panel.
Operation can also be made by pressing any numeric 
key corresponding to the number displayed. (e.g. Press 
the  2 key to adjust zoom.) 
Follow the instructions on the screen for subsequent 
operations.
Status 10/10/2008    10:10
Ready to copy.Copies
Quantity
Staple/Punch
Off Density
Normal 0
Zoom
100%
Duplex
2-sided
>>2-sided Auto
Combine
2 in 1
Paper
Selection
Downloaded From ManualsPrinter.com Manuals