Vodavi Triad 1/2/3 System Programming Manual

							9-8 Toll Restriction
Toll Restriction
Ente ri ng Toll  Tabl e
Pro g ram mi ng  S te ps
If the system is in the  programming mode,  continue using the program 
codes. If  starting to program  here, enter  the programming mode.
1. Press FLASH and  di al [70]. The  following message displays:
2 . To  pr ogra m All ow/De ny t abl es,  pr es s t he  ap prop ri at e Tab le  but t on 
and enter information as outlined in the following  procedures.
3. To  program Special Tables 1-3, it  is necessary to associate an area 
code to the  table.  This is  done  by pressing the appropriate AREA 
CO DE  TABL E b utt on a nd as si gn t he  ar ea  code.
4. To  display entries in any  of the tables, press the  DISPLAY TABLES 
button ( FLASH 70, Butt on  #12).  Entries in the Allow/Deny  tables 
display two at a  time. Entries in the  Special tables display  six at a  time 
in ascending  order.
Des crip ti on
All toll tables have been conveniently placed under one program code to 
allow  entry of  all toll restriction data.
EX   TA BL ES
ENTE R   BUTTON   NUMBER
Special Table 4 is reserved for the home area code and does not 
requ ire  an are a cod e en try. 
						

							To ll  R e s t r ic t i o n 9 - 9
The buttons  on the  digital terminal  are defined as shown below  when 
entering the  Toll  Restriction programming area:
When the  system searches the  Allow and Deny tables,  the entries  are 
checked starting with  Bin  01 and proceeding sequentially through the 
ta bl e t o th e l ast  bi n. I n ad dit i on the  A ll ow T abl e i s a lway s se ar c hed  bef ore  
looking at the Deny Table. Therefore, the entry order is important. Entries 
tha t  ar e s pe ci fi c (e .g.,  [1 71 6 ] ) ar e  pl aced  ahe ad  of e ntr i es  tha t  ar e m ore  
gene r al  (usua ll y i nclu de  Do Not  C ar e  digi t s;  e.g ., [ 1 D  1 ] ).
Once a  match is found in the Allow Table  that  references  a Special Table, 
the  numb er  dia le d ar e che cked f or a n all owe d code i n the S peci al  Tab le . I f 
a m atc h  is  not  foun d i n t he  Spe c ia l  Tab le , t he  sys te m c ont i nues  to  c hec k 
for a  match in the  next Allow  or Deny Table to check. The system does 
not return to the table that sent the call to the Special Table.
ALLOW
TAB LE ADEN Y
TABLE AALLOW
TAB LE BDENY
TABLE B
=1Q=2W=3E=4R
SPECIAL
TABLE 1SPECIAL
TABLE 2SPECIAL
TAB LE 3SPECIAL
TABLE 4
=5T=6Y=7U=8I
AREA CODE
TABLE 1AREA CODE
TABLE 2AR EA COD E
TAB LE 3DI SPL A Y
TABLES
=9O=10 P=11 A=12 S
=13 D=14 F=15 G=16 H
=17 J=18 K=19 L=20 ;
=21 Z=22 X=23 C=24 V 
						

							9-10 To l l  Res trictio n
All ow  Ta b le
Pro g ram mi ng  S te ps
1. Pr es s t he  ALLOW  TABLE  A or  ALLOW  TABLE  B f le xib le  but ton  
(FLASH 70, Bu tton  #1 o r #3). T he f oll owin g me ssa ge  is  shown  on 
the  d isp lay  te l epho n e:
The  fi rs t two  bi n l o c ati o ns di spl ay.
2. Enter a  valid  bin numb er (01–2 0)  of t he  bi n t o be  pr ogr amme d.
It is re comme nded  th at:
†B in 17  b e r es er ve d f o r an e ntr y th at re fe re nc es SP EC IA L TA B LE 1
†B in 18  b e r es er ve d f o r an e ntr y th at re fe re nc es SP EC IA L TA B LE 2
†B in 19  b e r es er ve d f o r an e ntr y th at re fe re nc es SP EC IA L TA B LE 3
†B in  20  b e r es er ve d f o r  an e ntr y  th at  re fe re nc es  the  Ho m e A r ea 
Code  Tabl e, SPEC IA L TA BLE  4.
3. Enter the  Allow Code.
[0–9],  [
6], [# ] = Corr espondi ng al low di gits  (number s)
MU TE  = Do  No t Ca re d i gi t (D)
TRANS =  Search Speci al  Table (S )
4. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay n ow upda te s.
5. When all  entries for  one table are  complete,  press the flexible button 
for  the next table.
Er a si n g a Bin  Nu m be r
1. Enter a  valid  bin numb er.
2. Press the HOLD  button.
ALLOW    TABLE   A
01 E 02E 
						

							To ll  R e s t r ic t i o n 9 - 1 1
Des crip ti on
Each Allow T able con ta ins  20 b in numbe rs . E ach b in numbe r may be up 
to  8  digits,  including Do Not Care digits and Search Special Table 
commands. Entries into the Allow Table represent exceptions to numbers 
or  cod es  tha t a re to be allowed only if they  would  otherwis e be res tricted  
by an entry in the Deny Table.
Ex a m pl e
If [1 555 1212] is allowed but [1+] numbers are denied,  by  an entry  into 
the Deny Table, [1 555 1212] is entered into the Allow Table as an allowed 
numbe r.
†Al l ow Tabl e A is  re fe re nc ed and sea rc he d f ir st  (be for e Deny  Tabl e A) 
when  St at ion  COS  i s 2  a nd CO  Li ne  CO S i s  ei the r  1  or  2.
†Al l ow Tabl e  B is  r efe re nc ed  and  look ed  at  fi rs t  (be fore  D eny Ta ble  B) 
when  St at ion  COS  i s 3  a nd CO  Li ne  CO S i s  ei the r  1  or  3.
†Whe n St at io n CO S i s  4  and C O L ine  CO S  is  1  bot h al l ow t abl es  ar e 
looked  at  first (Allow Table A first,  then Allow Table B) then  both deny 
ta bl es (De ny Tabl e A  fi rs t, the n D eny Ta bl e B ) .
Do  N ot  C are  d igi t s s peci fy tha t the  sy st em shoul d consi de r any d igi t  
di ale d i n t hat  p osi ti on a s a  mat ch. D o Not  C ar e d igi ts  sh ould  not  be  
entered as the last  digit in an  entry, as this would be an unnecessary 
or mea ning le ss command.
Search Special Table comma nds  must  be  e nte re d i n a  sp eci fic 
manner  and  should always be the last entries  in  the Allow Table. It is 
re c o mmen ded th at th e l as t fo u r bi ns (1 7–2 0)  i n t he  Al low  Ta bl e b e 
re se r ved  fo r  re fe re nc ing  th e f o ur  spe c ial  t ab le s wi t h t he  re fer enc e  t o  
the  hom e a re a code  (S pe cial  Tab le  4 ) al ways  be ing  loca te d i n b in 
number  20.  Search  Special table commands can only be entered into 
the  a ll o w t abl es .
Rem ember to enabl e 911 fo r all Classes of Service 
						

							9-12 To l l  Res trictio n
Rule s f or  E nt ri es  t h at  R efe rence  Spe ci a l T a bl es
For  e ntr ie s  re fer e nc ing  the  fi r st  t hre e  spe c ia l t ab le s a  sp ec i fic   are a  c ode 
must  b e i de nti fi ed  (one  for  ea ch t abl e  nee de d). T he n mak e no te  as  t o 
how the  numbers are dialed when dialing numbers to this area  code  (i.e., 
with a  l ead ing  di git [1] or n o le adi ng  digi t [1] ).
The entry into the  Allow Table would  be  entered as follows:
†Lea ding  Di gi t [ 1]:  Enter [ BB]  [1] [XX X] [D DD]  [S]  or,
†Non-Le adi ng  [1]:  En te r  [BB] [XXX ] [D DD]  [S]
BB = Bi n Numb er (Bi ns 17-19)
XX X = Area  C ode  (must match  AREA-X en try )
DD D = D o No t C are  digi t (t hre e en trie s,  D ND  b utton )
[S] = S ea rch S pe cial  Ta ble  Comma nd (T RA NS  but ton)
For  an  ent r y t hat  r efe r enc e s t he  Home  A re a C ode  ta bl e ( Spe c ia l T abl e  4)  
the entry  may  also be entered  to  expect or  not expect a  leading digit [1]. 
In  fact, in some cases  it may be desirable to enter both of the following 
ent r ie s:
†Lea ding  Di gi t [ 1]  --  Enter [BB]  [1]  [DD D] { S}
 and /or,
†Non-Le adi ng [1] --  Enter [BB] [DD D] {S }
BB = B in nu mber  (Bi n 20)
DD D = D o No t C are  digi t (t hre e en trie s,  MUTE butto n)
{S} = S ea rch S pe cial  Ta ble  Comma nd (T RA NS  but ton)
Deny Table
Pro g ram mi ng  S te ps
1 . Pr es s t he  DE NY TABL E A o r D ENY  TABLE  B fl exi bl e  but ton (F LA SH 7 0, 
Bu tton  #2 o r #4). T he f oll owin g me ssa ge  dis pl ays:
If both l ead ing  d igit  [1] and  non-l ead ing d igit [1] entries ar e made 
to r efer en ce the  same tabl e, it i s ne cessary  to plac e t he le adin g di git 
[1]  en try  ahe ad  of th e  non -le adin g d igit  [1] e ntry  in  th e  Al low  Ta ble .
DENY   TABLE   A
01 E 02E 
						

							To ll  R e s t r ic t i o n 9 - 1 3
2. When the  first two bin  locations are displayed, enter  the 2-digit  bin 
nu mber ( 01–10) of  the bin to be programmed.
3. Enter the  deny code:
[0–9] ,  [6], [#] = Corr esponding deny dig its numb ers
MUTE = Do No t Care digi t
4. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay n ow upda te s.
5. When all  entries for  one table are  complete,  press the flexible button 
for  the next table.
Er a si n g a Bin  Nu m be r
1. Enter a  valid  bin numb er.
2. Press the HOLD  button.
Des crip ti on
Each De ny T able conta ins  ten bin numbe rs . E ach b in numbe r may be up 
to  eight-digits including {Do Not Care}  digits.  Entries in the  Deny Table 
re pr es ent  numb er s or  c ode s t hat  ar e  to  be  deni ed  or  re st ri c te d.  Common  
entries would  be  [1] for restricting all  [1+]  type of calls. Exceptions to this 
re st ri c t io n  wo uld  be  en te re d i nt o  t he  Al lo w  Ta ble .
†De ny Tabl e  A  is  r efe re nc ed  and  se arc he d o nly  aft er  t he  Al l ow Tabl e  A 
is  che ck ed  when  St at ion  COS  i s 2  a nd CO  Li ne  CO S i s  ei the r  1  or  2.
†De ny Tabl e  B i s r ef er ence d and  se ar ched  only  aft er  t he  A ll ow Tabl e  B 
is  che ck ed  when  St at ion  COS  i s 3  a nd CO  Li ne  CO S i s  ei the r  1  or  3.
†Whe n St at io n CO S i s  4  and C O L ine  CO S  is  1,  bot h a ll ow t abl es  ar e 
looked  at  first (Allow Table A first,  then Allow Table B) then  both deny 
ta bl es (De ny Tabl e A  fi rs t, the n D eny Ta bl e B ) .
- D o Not  Ca re di git s  spe cif y t hat  th e s yst em  shoul d cons ide r  any d igi t 
di ale d i n t hat  p osi ti on a s a  mat ch. D o Not  C ar e d igi ts  sh ould  not  be  
entered as the last  digit in an  entry.
- S ea rch  Spe cia l Tab le  comma nds  cannot be  e nte re d into the D eny 
ta bl es. 
						

							9-14 To l l  Res trictio n
Spe cial Table
Pro g ram mi ng  S te ps
To prog ram  a Spe cia l T abl e , i t is  fi rs t nece ssa ry to ass ign  an are a code to 
the table (except for the home area code).
1. Press the appropriate AREA  CODE TABLE (#1 to #3) flexible button 
(FLASH 70, Bu tton s #9 to #11). The following  message displays:
2. Enter a valid area code.
3. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay u pdat es .
Entering  Office Codes in a Special Table
1. Press the SPECIAL TABLE (#1  to  #4) flexible  button (F L ASH 7 0, 
Bu tton s #5 to #8) t hat  c o r re sp o nds  to   the  ar ea  c o de  pr o gra mme d 
above. T he  following mess age displays:
XX X =  A r e a  C o d e
2. Enter the  office codes  that  are to be allowed  or  removed as follows:
XXX [1]  = Al l ow Code
XXX  [0]  =  Remove  C ode  from  th e l i st
(XXX = An offi ce cod e f rom 20 0  t o 9 99 )
3 . Pr es s H OLD  af te r  eve r y c ode  en te re d. A  c onfi r mat ion  tone  i s  hear d 
a nd t he dis pl ay upd ate s. Mu lt ip le  codes  may be ent er ed in a r ow. The  
display updates  showing the  first six  codes in ascending order.
SPECIAL   TABLE    1 AC
SPECIAL   TABLE   1 AC   XXX 
						

							To ll  R e s t r ic t i o n 9 - 1 5
Des crip ti on
The Special Tables  provide  greater flexibility in designing a  toll plan for  a 
par t icul ar  si te .
†Each  Specia l  Ta ble a llows entry of  up to 800 of fice codes ( 200–999).
†Three of  these tables must  be  assigned an area code by  which they 
are referenced. The fourth  table is  reserved  for  the home area code 
and re qui re s no are a co de ent r y.
†The  Sp ec i al  Tabl es  ar e  re fer enc e d t hr ough e ntr i es  in  th e a ll ow t abl es . 
Four  area  codes,  including  the home a rea code, can  be referenced  to 
these special tables for further definition. When  a Special Table is 
referenced, entries must  be  made in the  Special  Table specifying 
what  off ice  codes  ar e  al lowe d.
†Code s can b e ad ded  to t he Al low l is t or  r emove d fr om t he l is t.  When a  
Spe cia l  Ta ble  i s  ch ecke d fo r a  mat ch t o a  3 -di git  code  a nd not  f ound, 
the  s yst em  conti nue s t o se ar ch t he  nex t A l low/ D eny Tab le  t o be  
c hec ke d. T he s yst em  does  not  re tur n t o t he A l low Tab le  whi c h rout ed  
the call to the  Special Table. By  default,  no codes are on  the Allow list.
ALLOW
TAB LE ADEN Y
TABLE AALLOW
TAB LE BDENY
TABLE B
=1Q=2W=3E=4R
SPECIAL
TABLE 1SPECIAL
TABLE 2SPECIAL
TAB LE 3SPECIAL
TABLE 4
=5T=6Y=7U=8I
AREA CODE
TABLE 1AREA CODE
TABLE 2AR EA COD E
TAB LE 3DI SPL A Y
TABLES
=9O=10 P=11 A=12 S
=13 D=14 F=15 G=16 H
=17 J=18 K=19 L=20 ;
=21 Z=22 X=23 C=24 V 
						

							9-16 To l l  Res trictio n
Disp lay Toll  Tabl e Entri es
Pro g ram mi ng  S te ps
Press the DISPLAY TABLES flexible button (FLA SH 70 , Bu tton #12) while 
entering information into  a table.
Viewing  Entries in an Allow or Deny Table
Two  entries at  a time are displayed o n the  bottom  line  of the  display.
1. Pres s the  DISPLAY TABLE S b utton a gain, the  next highe r  bins  displays.
2 . Whe n th e l ast  e ntr i es  are  di spl aye d, pr es s t he D IS PLAY  TA BLES  but to n 
again to show the first two entries.
X = Allow or Deny Code
E = End o f Entry
Viewing  Entries in a Special Table
Si x 3-di gi t  codes  al lowe d  dis pla y i n a scend ing  ord er  star ting  with the  
lowe st  e ntr y.
Press  the DISPLAY  TABLES button again, the  next 6 entries display. This 
continues until  all codes  are displayed.
XXX= Area Code
YYY= Allowed Offi ce Code
Des crip ti on
To  view all entries  in  the toll tables using the display on  the Executive 
telephone, press, the DISPLAY TABLES flexible button ( FLASH 70, 
Bu tton #12) multiple  times to scroll through the entries.
ALLOW    TABLE   A
01    XXXXXXXE 02    XXXXXXXX
SPECIAL   TABLE    1 AC   XXX
YYY   YYY   YYY   YYY   YYY   YYY
It is  re comme nde d to v iew al l en trie s  i n the  Al low an d De ny T abl e 
be fo re  lea vin g p rogra mming . Entr ies c an  be  en tere d n ea r th e b ottom 
of the list for searching the special tables or entries made in error. 
Viewing the entire Allow Table ensures proper entry and operation. 
						

							10
Least Cost Routing
(LCR)
This c hapter provides the functional steps  nec essary to use  the  LCR
features with the ST A RPL US Tria d 1/2/3  System. To implement the
most ec onomic al  routes for an outside c all,  you must  first enter the
Programming Mode.