Vodavi Triad 1/2/3 System Programming Manual

							3-54 IS DN Pro gram ming - Pag e A
Fr a mi ng
Pro g ram mi ng  S te ps
1 . Pr es s t he  FR A M I NG fl ex ibl e  but ton (FLASH 45, Page A, Bu tton #3).
2 . To  vi ew  a Fr ami ng s et t ing,  ent er  a  val id  numbe r  (0 -2 ).
Des crip ti on
Changes to the  Framing area are  not possible at this time  (setting =  ESF).
NT  /  TE  Mo de
Pro g ram mi ng  S te ps
1 . Pr es s t he  NT /T E  M ODE  fl exi bl e  but ton (FLASH  45, Page A, 
Bu tton #4).
2 . To   vi ew  an N T/ TE  se tt i ng, e nte r  a v ali d n u mbe r ( 0- 1).
Des crip ti on
The TE Mode setting cannot be changed.
Power
Pro g ram mi ng  S te ps
1. Press the POWER flexible button (FL ASH  45, Page A , Bu tton  #5).
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
FR AMIN G 0- 2
ESF
NT / TE  MODE 0-1
TE
POWER 0-1
DISA BLE D 
						

							IS DN Programm in g - Page  A 3 -55
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Des crip ti on
De faul t = Dis abl ed
Directory Number
Pro g ram mi ng  S te ps
1 . Pr es s t he  DI R EC TOR Y  N UM BER  fl ex ibl e  but ton (FLASH  45, Page A, 
Bu tton  #6).
2. Enter a  val id  numbe r (0-9,* ,#)  on the  dia l  pad  (up  to 24 di gi ts ). T his  
number is  sent  as the calling  party number on  all channels  of the 
selected PRIB.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Max Out I-Frames
Pro g ram mi ng  S te ps
1. Press the MAX OUT  I-FRAMES  flexible button ( FLASH 45, Pag e A, 
Bu tton  #7).
2. Enter a valid number (000-127)  on the  dial  pad.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
DIRECTORY NUMBER 0-9, *,#
XX
MAX   OU T  I  - FR A MES 0 00- 12 7
K 001 
						

							3-56 IS DN Pro gram ming - Pag e A
Leading 1
Pro g ram mi ng  S te ps
1. Press the LEADING 1 flexible button ( FLA SH 45,  Page A, Butto n #8).
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Des crip ti on
0 dis abl es  t he le adi ng 1  f rom bei ng sen t to the  CO  wh en u ser s dia l 
nationa l  long  dis ta nce num bers.  1  enab le s the  le ading 1 to be  se nt  to the  
CO  on n at iona l l ong  dis ta nce n umbe rs.  I f e nabl ed , a nd t he  use r  does  not  
di al  a 1 ,  the  1  wi ll  a u to ma ti c al ly  be  app li ed . De fau l t  =  Ena bl ed
Leading 011
Pro g ram mi ng  S te ps
1. Press the LEADING 011 flexible  button (FLASH  45, Page A, 
Bu tton #9).
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
LEA DING  1 0- 1
EN AB LE D
LEA DING  01 1 0- 1
EN AB LE D 
						

							IS DN Programm in g - Page  A 3 -57
Des crip ti on
0 dis abl es  t he le adi ng 0 1 1 from  be ing  se nt to th e C O when use rs  di al  
international numbers. 1 enables the  leading 011 to be sent to the CO on 
int e rna ti onal  numb er s.  If  ena bl ed,  and  th e us er  doe s  not  dia l  a 0 1 1,  th e 
01 1  wi ll  aut oma ti cal ly  be  app li ed.  De faul t  =  Ena ble d
7/8  Di git Nu mber  Plan
Pro g ram mi ng  S te ps
1. Press the 7/8 DIGIT NUMBER  PLAN flexible  button (FLASH 45, 
Page A, But to n # 10).
2 . Ent er  a  0 or 1 on t he di al pad to se le ct the  de si re d N umbe r Pl an.
[0] =  Se le cts ITU  numbe r  pl an
[1] =  Se le cts CO num ber p lan
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Des crip ti on
De faul t = IT U (I SD N pl an)
Nortel  DMS 1 00 Onl y
1. Change  Flash 45, bu tton 10  (Numbering Plan) to CO by  dialing 1 
HOL D.
2 . Se t  the  de fi nit i on i n t he  DMS  10 0  Ce ntr al  O ffi ce S wit ch.
†The DMS 100 Office  refers  to  this  switch as National or N12 
Standard  so they know not to look at this parameter in their 
swi tch.
†LTDEF  should be set to NI PRI N12 V1.
7/ 8  D GT  N U MB ER  PL AN 0- 1
ITU
When connecting a PRI to a Nortel DMS 100, enter a 1 for the number 
pla n. 
						

							3-58 IS DN Pro gram ming - Pag e A
Calli ng Number
Pro g ram mi ng  S te ps
1. Press the CALLING  NUMBER  flexible button ( FLASH 45, Pag e  A, 
Bu tton  #11).
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Des crip ti on
0 dis abl es  t he call i ng pa rt y n umbe r f rom be ing se nt to the  C O. 1 wil l 
enable the calling party  number  feature  and  the number will be sent to 
the  C O.  De fau l t  =  Enab le d
Loopback
Pro g ram mi ng  S te ps
1 . Pr es s t he  LOO P BAC K fl exi bl e b utt on ( FLA SH 45,  Page A, 
Bu tton #12).
2. Enter a  val id  numbe r (0-2) on  the  di al  pa d. 
[0] =  Normal  mode
[1] =  Ne ar  end  mode
[2] =  Far end  mode
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Des crip ti on
De faul t = Norm al
CAL LING NUMBE R 0- 1
EN AB LE D
LOOPBAC K 0-2
NORM AL 
						

							IS DN Programm in g - Page  A 3 -59
10 Digit Number Plan
Pro g ram mi ng  S te ps
1 . Pr es s t he  10  DI GI T NUM BE R  P LAN  fl exi ble  but t on (F L ASH 4 5,  Pag e  A,  
Bu tton  #13).
2 . Ent er  a  0,  1 , or  2  on  the  di al  pa d t o s el ect  t he  des ir ed  Numb er  Pla n.
[0] =  Se le cts ITU  numbe r  pl an
[1] =  Se le cts CO num ber p lan
[2] =  Unknow n
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Des crip ti on
De faul t = IT U
11 Digit Number Plan
Pro g ram mi ng  S te ps
1 . Pr es s t he  10  DI GI T NUM BE R  P LAN  fl exi ble  but t on (F L ASH 4 5,  Pag e  A,  
Bu tton  #14).
2 . Ent er  a  0,  1 , or  2  on  the  di al  pa d t o s el ect  t he  des ir ed  Numb er  Pla n.
[0] =  Se le cts ITU  numbe r  pl an
[1] =  Se le cts CO num ber p lan
[2] =  Unknow n
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Des crip ti on
De faul t = IT U
10  D I GI T  NU MB ER  PL AN 0- 2
ITU
11  D I GI T  NU MB ER  PL AN 0- 2
ITU 
						

							3-60 IS DN Pro gram ming - Pag e A
I SD N Pr ogra m m in g - Pa ge B
Pro g ram mi ng  S te ps
1. Press FLASH and  di al  [45 ].  The following message displays:
2. Enter a valid number for the range of lines being programmed. If only 
on e l in e i s  bei ng  prog ram med,  ent er  t hat  num ber  t wi ce  (0 0 1  00 1) .
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
d is play  upd ate s.  Fle xi ble  bu tt on # 19  (P age  A ) i s  li t.
4. Press button #20 to select Page B.  The following message displays to 
indicate current programming of  that line or group of  lines:
XXX-XXX = CO  Line Range
00 1- 04 8 = Tria d 1/2
00 1- 14 4 = Tria d 3
Des crip ti on
When entering  the CO Line attributes portion of the  database, the 
programmer may decide  to  enter information for a  range  of CO lines or 
one  spe cifi c CO Li ne.  Range  programmi ng l ets the  pro gra mmer chan ge a  
specific parameter  or a few parameters  for an  entire range of CO  Lines 
leaving  intact the  remaining data  fields that do not require change.
ISDN  AT TRIBUTES
SEL ECT  A  SLOT  RANGE
If HOLD is pressed witho ut enter ing a CO ra nge, ALL CO li nes 
(001-048 o r 001-144) are selected .
XXX - XXX  PA GE   B
EN TE R  B U TTON   N UM BE R
IMPORTANT --
These timers 
should not  be adjusted UN LE SS  work ing  w ith T ec hni cal 
S uppo rt or yo ur te lep hon e comp any . 
						

							IS DN Programm in g - Page  A 3 -61
Thos e  dat a fi e lds  c ont inue  t o op er at e wi t h t he  pr evi ousl y p rogr amm ed 
dat a.
Maximum Number Retransmission
Pro g ram mi ng  S te ps
1. Press the MAX # RETRANSMSN flexible button ( FLA SH 45,  Pag e B, 
Bu tton  #1).
2. Enter a  val id  numbe r (0-9) on  the  di al  pa d.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
MA X  #  O F
RETRA NSM ISSIO NSMA X
OCTETSMAX TEI
RQ STMAX XID
RETRA NSM ISSIO N
=1Q=2W=3E=4R
T-2 00MIN TEI ID
CHK MSGMIN TEI
ID RQSTMSG EX CH AN GE
TIMER
=5T=6Y=7U=8I
MI N X I D
RETRA N SMINTER-D IGIT
T/OSE T  U P
TIMERDISCONNECT
TIMER
=9O=10 P=11 A=12 S
REL EA SE
REQ UESTLINK
DISCO NNEC TCALL
PRO C EED INGCO NNEC T
REQ UEST
=13 D=14 F=15 G=16 H
RESTA RT
REQ TIMERPAGE APAG E B
=17 J=18 K=19 L=20 ;
PAGE CPR EV IOU SNEX TNEW  R ANGE
=21 Z=22 X=23 C=24 V
MAX  #  R ETR A NS MSN 0- 9
N200    3 
						

							3-62 IS DN Pro gram ming - Pag e A
Maximum Octets
Pro g ram mi ng  S te ps
1 . Pr es s t he  M A X O CT ETS  fl exi bl e  but ton (FLASH  45, Page B, 
Bu tton #2).
2. Enter a valid number (000-999)  on the  dial  pad.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.  (000 = D is able)
Maximum TEI ID Request
Pro g ram mi ng  S te ps
1. Press the MAX TEI ID RQST flexible  button (F LA SH 45 ,  Pa ge  B,  
Bu tton  #3).
2. Enter a valid number (000-999)  on the  dial  pad.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Maximum XID Retransmission
Pro g ram mi ng  S te ps
1 . Pr es s t he  MA X XI D  RETRA NS MIS SI ON  fl exi bl e b utt on ( FLA SH 45, 
Page B, Bu tton #4).
2 . Ent er  a  val id  numbe r  (0 -9  se conds)  on t he  di al  pad.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
MAX   OCT ETS 0 00- 99 9
N 20 1    260
MAX   TE I   I D   R QST 0 00- 99 9
N 20 2    003
MAX  XID  RE TRANSMIS SION 0-9
N204    3 
						

							IS DN Programm in g - Page  A 3 -63
T- 2 0 0
Pro g ram mi ng  S te ps
1. Press the T-200 flexible  button (FLASH 4 5, Page B,  Bu tton  #5).
2 . Ent er  a  val id  nu mbe r  (0 0- 99  s ec o nds ) o n  the  di al  pa d.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Minimum TEI ID Check Message
Pro g ram mi ng  S te ps
1. Press the MIN TEI ID CHK MSG  flexible button ( FLASH 45, Pag e  B, 
Bu tton  #6).
2 . Ent er  a  val id  nu mbe r  (0 0- 99  s ec o nds ) o n  the  di al  pa d.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Minimum TEI ID Request
Pro g ram mi ng  S te ps
1 . Pr es s t he  M IN  T EI  ID  R Q ST  fl exi bl e b utt on ( FLA SH 45,  Pag e B, 
Bu tton #7).
2 . Ent er  a  val id  nu mbe r  (0 0- 99  s ec o nds ) o n  the  di al  pa d.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
T2 00 0 0-9 9
01    
MIN  T EI  ID  CHK  MSG 0 0-9 9
T2 01     01
MIN  T EI  ID  RQS T MSG 0 0-9 9
T2 02     02