Sharp Mxm264n User Guide

							5-113
SCANNER/INTERNET FAX
Contents
MANUALLY RECEIVING INTERNET FAXES
If the interval for checking for received faxes is somewhat long and you wish to check immediately, you can manually 
initiate reception.
Touch the [I-Fax Manual Reception] key to connect to the mail server and retrieve received faxes.
If POP3 server settings are not configured in the Web pages, the [I-Fax Manual Reception] key is greyed out to prevent 
selection.
System Settings: Fax Data Receive/Forward (page 7-22)
This setting is used to hide the [I-Fax Manual Reception] key that appears in the base screen of Internet Fax mode. When the 
[I-Fax Manual Reception] key is hidden, manual reception is initiated by touching the [Reception Start] key in the screen that 
appears when Fax Data Receive/Forward - I-Fax Settings is selected.
AutoAuto
Auto
File
Quick File
I-Fax Manual
Reception
Send Settings
Address Entry
Address Book
USB Mem. ScanFaxInternet FaxPC Scan
Special Modes
File Format
Resolution
Exposure
OriginalScan:
Scan
Send:
200X100dpi
TIFF-FAddress Review
Preview 
						

							5-114
SCANNER/INTERNET FAX
Contents
PRINTING A PASSWORD-PROTECTED FAX 
(Hold Setting For Received Data Print)
Hold Setting for Received Data Print in the system settings (administrator) can be enabled to have faxes received to 
memory without being printed. To print the faxes, a password must be entered. When this function is enabled, a 
password entry screen appears in the touch panel when received Internet faxes are retrieved.
When the previously programmed 4-digit password is entered with the numeric keys, printing begins.
The [Cancel] key can be touched to close the password entry screen; however, the data in memory key () will blink 
in the touch panel. The password entry screen will reappear when you touch the blinking key () or change modes.
When Received Data Image Check Setting is enabled in the system settings (administrator), a password can be 
entered to display the received data list screen. If you wish to check an image before printing it, continue from step 2 on 
the next page.
 The received faxes will be retained in memory regardless of whether they were received automatically or manually.
 If Fax Data Receive/Forward is enabled in the system settings so that received faxes are forwarded to another machine, 
faxes retained in memory are also forwarded. At that time, the same password entry screen will appear as for printing. 
Forwarding will not take place unless the password is entered.
System Settings (Administrator): Hold Setting for Received Data Print
Enable this setting to have faxes received to memory without being printed. This setting is also used to program the 
password that must be entered to print the faxes.
Cancel
Received data is stored.
Enter password via the 10-key. 
						

							5-115
SCANNER/INTERNET FAX
Contents
CHECKING THE IMAGE BEFORE PRINTING
This function requires the hard disk drive.
When Received Data Image Check Setting is enabled* in the system settings (administrator), you can check a 
received image in the touch panel before printing it out. When this function is enabled, follow the steps below to print a 
received image.
* The factory default setting is disabled.
Depending on the size of the received data, part of the image in the image check screen on the touch panel may not appear.
1
When an image is received, a 
confirmation prompt will appear. Touch 
the [Yes] key.
If this message appears while you are configuring settings of 
any type and you touch the [Yes] key, the settings that you are 
configuring will be cancelled. If this message appears in 
another mode, you will return to the base screen of image send 
mode after checking the image.
2
Select the received image
(1) Touch the key of the received image that 
you want to check.
Multiple received images can be checked.
(2) Touch the [Image Check] key.
 To show thumbnails of the received images, touch the 
[Thumbnail] key.
 To delete an image that has been selected, touch the 
[Delete] key. To print an image that has been selected, 
touch the [Print] key.
3
Check the received image and then 
touch the [Print] key.
Printing begins.
For information on the image check screen, see IMAGE 
CHECK SCREEN (page 5-117).
If the screen of step 1 appears when you are configuring settings in the setting screens of any of the modes, the configured 
settings will be cancelled if you view the image. After viewing the image, you will return to the base screen of image send 
mode, regardless of which mode you were in previously.
System Settings (Administrator): Received Data Image Check Setting
Use this to specify whether or not a received Internet fax can be viewed before it is printed.
YesNo
The memory has received data.
Check the data?
Received Data ListBack
Not checked10:28
04/04/2012
04/04/2012
BBB BBB9876543210
BBB BBB
CCC CCC
0612345678
0123456789
BBB BBB
AAA AAA
1
5
ThumbnailSelect All
04/04/2012
04/04/2012
04/04/2012
04/04/2012
10:14
10:12
10:08
10:00
10:00
Not checked
Not checked
Checked
Checked
Checked
Image CheckDeleteForwardPrint
(1)
(2)
Image CheckBack
Display Rotation
Print
1 / 3AAA AAA04/04/201210:28
/00100001 
						

							5-116
SCANNER/INTERNET FAX
Contents
CHECKING THE IMAGE BEFORE 
FORWARDING
This function requires the hard disk drive.
When Received Data Image Check Setting is enabled in the system settings (administrator), you can select the 
received data from the list and forward it to the addresses recorded in the address book. When this function is enabled, 
follow the steps below to forward the received image.
* The factory default setting is disabled.
Depending on the size of the received data, part of the image in the image check screen on the touch panel may not appear.
1
When an image is received, a 
confirmation prompt will appear. Touch 
the [Yes] key.
If this message appears while you are configuring settings of 
any type and you touch the [Yes] key, the settings that you are 
configuring will be cancelled. If this message appears in 
another mode, you will return to the base screen of image send 
mode after checking the image.
2
Select the received image
(1) Touch the key of the received image that 
you want to check.
Multiple received images can be checked.
(2) Touch the [Forward] key.
 To show thumbnails of the received images, touch the 
[Thumbnail] key.
 The receieved image can be checked by touching the 
[Image Check] key. 
This function requires the hard disk drive.

IMAGE CHECK SCREEN (Page 5-117)
3
Touch the Forward Destination from the 
address book to select it.
Multiple forwarding addresses can be checked.
YesNo
The memory has received data.
Check the data?
Received Data ListBack
Not checked10:28
04/04/2012
04/04/2012
BBB BBB9876543210
BBB BBB
CCC CCC
0612345678
0123456789
BBB BBB
AAA AAA
1
5
ThumbnailSelect All
04/04/2012
04/04/2012
04/04/2012
04/04/2012
10:14
10:12
10:08
10:00
10:00
Not checked
Not checked
Checked
Checked
Checked
Image CheckDeleteForwardPrint
(1)
(2)
III III
GGG GGG
EEE EEE
CCC CCC
AAA AAA
JJJ JJJ
HHH HHH
FFF FFF
DDD DDD
BBB BBB12
51510
Address Review
ToCc
ABCDFreq.EFGHIJKLMNOPQRSTUVWXYZetc.
Start forward.Sort Address 
						

							5-117
SCANNER/INTERNET FAX
Contents
IMAGE CHECK SCREEN
This function requires the hard disk drive.
This section explains the image check screen.
(1) Information display
This shows information on the displayed image.
(2) Preview image
An image of the selected received image appears.
If the image is cut off, use the scroll bars at the right and 
bottom of the screen to scroll the image. Touch a bar and slide 
it to scroll. (You can also touch the   keys to scroll.)
(3) Change page keys
When there are multiple pages, use these keys to 
change pages.
  keys:  Go to the first or the last page.
  keys: 
Go to the previous page or the next page.
Page number display: This shows the total number of 
pages and the current page 
number. You can touch the 
current page number key and 
enter a number with the numeric 
keys to go to that page number.
(4) Display Rotation key
This rotates the image right or left by 90 degrees. The 
rotation applies to all pages in the file, not just the 
displayed page.
(5) [Print] key
Touch to start printing.
(6) Display zoom key
Use this to set the zoom ratio of the displayed image. 
Changes from the left in the order Full Page, Twice, 
4 Times, 8 Times. The setting applies to all pages in 
the file, not just the displayed page.
(7) Image select key
When multiple images are selected for preview display, 
use this to change the displayed images.
4
Start forward
Touch the [Start forward.] key.
If the screen of step 1 appears when you are configuring settings in the setting screens of any of the modes, the configured 
settings will be cancelled if you view the image. After viewing the image, you will return to the base screen of image send 
mode, regardless of which mode you were in previously.
System Settings (Administrator): Received Data Image Check Setting
Use this to specify whether or not a received Internet fax can be viewed before it is printed.
III III
GGG GGG
EEE EEE
CCC CCC
AAA AAA
JJJ JJJ
HHH HHH
FFF FFF
DDD DDD
BBB BBB
ToCc
12
51510
Address Review
ABCDFreq.EFGHIJKLMNOPQRSTUVWXYZetc.
Sort AddressStart forward.
AAA AAA
Image Check
04/04/2012  10:281 / 3
Display Rotation
Print
Back
00010010
(3)(5)(1) (2)(4)(7)(6)
A preview image is an image for display on the touch panel. It will differ from the actual print result. 
						

							5-118
SCANNER/INTERNET FAX
Contents
FORWARDING RECEIVED INTERNET 
FAXES TO AN ADDRESS  
(Inbound Routing Settings)
This function requires the hard disk drive. 
Received Internet faxes can be automatically forwarded to a facsimile internet fax, e-mail address, file server address, 
desktop address, or network folder address. When this function is enabled, you can also have received Internet faxes 
forwarded without printing them.
CONFIGURING INBOUND ROUTING SETTINGS
All inbound routing settings are configured in the Web pages. For the procedure for accessing the Web pages, see 

ABOUT THE WEB PAGES OF THIS MACHINE (page 1-26) in 1. BEFORE USING THE MACHINE. 
The following explanation assumes that the Web pages have been accessed with administrator rights. 
To configure inbound routing settings, follow the steps below.
When faxes forwarded using this function are printed at the forwarding destination, the date and time of reception cannot be 
printed on the faxes. (Receiving Date & Time Print is disabled.)
1
Enabling the inbound routing function.
(1) In the Web page menu, click [Application 
Settings], [Inbound Routing Settings], and 
then [Administration Settings].
(2) Select [Enable] in Inbound Routing and 
click the [Submit] button.
Users without administrator rights can be prohibited from storing, editing, and deleting forwarding tables in this screen, 
and from specifying which table is used. To do so, select the checkboxes below  .

Disable Registration of Forward Table    Disable Change/Delete of Forward Table    Disable Change of Forward Approval
When inbound routing is enabled, you can also specify whether or not you wish the machine to print the forwarded faxes.
To have all received faxes printed before being forwarded, select Print Out All Report in Print Style Setting. To 
have received faxes printed only when an error prevents forwarding, select Print at Error.
If an error occurs when [Not Print and Forward to the Following E-mail Address at Error] is selected, received data is 
not printed, but is forwarded to the specified e-mail address.
After configuring the settings, be sure to click the [Submit] button.
Forwarding
Received Internet fax The machine 
						

							5-119
SCANNER/INTERNET FAX
Contents
2
Storing sender addresses.
If you wish to have only faxes from specified addresses 
forwarded, store the desired sender addresses. Send 
addresses stored here can be selected from a list when you 
store a forwarding table.
(1) Click [Sender Number/Address 
Registration] in the [Inbound Routing 
Settings] menu in the Web page.
(2) Enter the sender address in Internet Fax 
Address or Fax Number as appropriate, 
and click the [Add to List] button.
The entered address will be added to the Address to be 
Entered list.
 Specify whether the address will be directly entered 
(maximum of 1500 characters) or selected from a 
global address book by clicking the [Global Address 
Search] button.
 To store multiple addresses, repeat this step.
(3) When you have finished adding addresses, 
click the [Submit] button.
 A maximum of 500 sender numbers/addresses can be stored.
 To delete an entered address, select the address in Address to be Entered and click the [Delete] button. 
						

							5-120
SCANNER/INTERNET FAX
Contents
3
Store a forwarding table.
Follow the steps below to store a forwarding table that 
combines a specified sender and forwarding address.
(1) Click [Inbound Routing Settings] in the Web 
page menu and click the [Add] button.
(2) Enter a Table Name.
(3) Select the line used for reception.
(4) Select the sender whose faxes will be 
forwarded.
 To forward all received faxes, select [Forward All 
Received Data].
 To forward only data received from specific senders,
select [Forward Received Data from Below Sender]. To 
forward all data except data from specific senders, 
select [Forward Received Data from Senders except 
Below]. Select the appropriate senders from the list and 
click the [Add] button.
(5) Select the forwarding address.
 To always forward received data, select [Always 
Forward].
 To specify a day and time on which received data will 
be forwarded, select [Forward on Selected Day & Time] 
and select the checkbox ( ) of the desired day of the 
week. To specify a time, select the [Set Forwarding 
Time] checkbox ( ) and specify the time.
(6) Select the file format.
The format can be set separately for each forwarding 
address (for each of forwarding addresses 1, 2, and 3 in 
the table).
(7) Select the forwarding address.
Forwarding addresses can be selected from the 
machines address book. (Multiple addresses can be 
selected.) A maximum of 1000 forwarding addresses can 
be stored (a combined maximum of 100 facsimile, internet 
fax, file server, desktop, and network folder addresses 
can be stored).
(8) Click [Submit].
 When selecting senders from the Sender Number/Address Setting list, you can use the [Shift] key or the [Ctrl] key 
on your keyboard to select multiple senders.
 A maximum of 50 forwarding tables can be stored.
 Images sent in TIFF format may not display correctly in some recipient environments. In this event, change the file 
format to PDF.
 Up to three forwarding day and time settings can be set for one forwarding table, and a forwarding destination can 
be set for each set time. To configure these settings, use the forwarding list tabs to access each setting.
(8)(7)
(3)(2)(4)
(6)(5) 
						

							5-121
SCANNER/INTERNET FAX
Contents
4
Specifying forwarding tables to be used.
To use the inbound routing function, enable the forwarding 
tables that you wish to use from among the stored tables.
(1) Click [Inbound Routing Settings] in the Web 
page menu.
(2) Select [Always Forward] or [Forward on 
Selected Day & Time] from the forwarding 
table.
The forwarding permission settings that appear here are 
linked to the forwarding conditions set in step 3. If you 
wish to use different forwarding conditions than those set 
in step 3, set the forwarding permission settings.
(3) Click [Submit].
To delete a forwarding table, click the checkbox next to the table name so that it is selected   and click [Delete].
(2)
(3) 
						

							5-122
SCANNER/INTERNET FAX
Contents
This function requires the hard disk drive.
BASIC SCANNING PROCEDURE
You can install the scanner driver on your computer from the CD-ROM that accompanies the machine, and use a 
TWAIN* compliant application to scan an image using your computer.
Scanning from your computer is most useful for scanning a single original such as a photo, particularly when you want to 
adjust scan settings as you scan. By contrast, scanning at the machine is most useful for continuous scanning of 
multiple originals.
* An interface standard used for scanners and other image input devices. When the scanner driver is installed on your 
computer, you can use any TWAIN-compliant application to scan an image.
As an example, the procedure for scanning from the Sharpdesk application that accompanies the machine is 
explained below.
[At the machine]
SCANNING FROM A COMPUTER 
(PC Scan Mode)
 Scanning in PC scan mode is only possible when the scanner driver has been installed from the Software CD-ROM 
using the integrated installer. For the procedures for installing the scanner driver and configuring settings, see the 
Software Setup Guide.

This function cannot be used when it has been disabled using Disable Scan Function in the system settings (administrator).
 The procedures for selecting the scanner driver and starting scanning vary depending on the TWAIN-compliant 
application. For more information, see the manual for the application or Help.
 When a large image is scanned at high resolution, the amount of data will be very large and scanning will take a long time. 
Be sure to select appropriate scan settings for the original (text, photo, etc.).
1
Place the original.
Place the original face up in the document feeder tray, or face 
down on the document glass.
2
Touch the [PC Scan] tab to switch to PC 
Scan mode.
If the [PC Scan] tab does not appear, touch the   tab 
to move the screen.
When PC scan mode is selected, only the [Exit] key displayed in the touch panel can be used on the machine; no 
other keys can be used.
Exit
This machine is in the PC scan mode.
Do not remove the original.
Scanner IP address:250.160.102.106
USB Mem. ScanFaxInternet FaxPC ScanScan