Sharp Mxm264n User Guide

							2-73
COPIER
Contents
4
Touch the [OK] key.
You will return to the base screen of copy mode.
5
Place the original face down on the 
document glass.
Place the opened front cover and back cover face down.
6
Press the [START] key to scan the first original.
Scanning begins.
Scan the remaining original pages in the following order:
Opened inside of front cover and 1st page
Opened 2nd and 3rd page
·
·
·
Opened last page and inside of back cover
To cancel scanning...
Press the [STOP] key ( ).
7
Place the next pair of opened pages and press the [START] key.
Repeat this step until all original pages have been scanned.
To cancel scanning...
Press the [STOP] key ( ).
Special ModesOK
CancelOKBook Copy
Left
BindingRight
Binding
Cover
Setting 
						

							2-74
COPIER
Contents
8
Touch the [Read-End] key.
Copying will begin.
To cancel scanning and copying...
Press the [STOP] key ( ).
 Four original pages will be copied onto each sheet of paper. Blank pages will be automatically added at the end if the total 
number of original pages is not a multiple of four.
 When book copy is selected, 2-sided copying is automatically selected. When settings are selected that prevent 2-sided 
copying, the book copy function cannot be used.
To cancel book copy...
Touch the [Cancel] key in the screen of step 2.
Read-End
Place next original. Press [Start].
When finished, press [Read-End]. 
						

							2-75
COPIER
Contents
COPYING CAPTIONS ONTO TAB PAPER (Tab Copy)
Captions can be copied onto the tabs of tab paper. Prepare appropriate originals for the tab captions.
Tab copy is possible from the bypass tray.
RELATION BETWEEN THE ORIGINALS AND THE TAB PAPER
Tab copying with a left binding
Tab copying with a right binding
OriginalsPlacing the originalsLoading tab paper
 Document feeder tray
Insert the originals so that the side with no tab text 
enters first.
Load the tab paper so that the tab on the 
first sheet is toward you.
 Document glass
Place so that the side with the tab text is on the left.
OriginalsPlacing the originalsLoading tab paper
 Document feeder tray
Insert the originals so that the side with no tab text 
enters first.
Load the tab paper so that the tab on the 
first sheet is away from you.
 Document glass
Place so that the side with the tab text is on the left.
GHI
DEF
ABC
GHI
DEF
ABCABC
Prepare originals that 
match the tab positions.The image is shifted 
by the width of the tab
1
Final imageOriginals
1
Reverse 
side
1
1
Final imageOriginals
1
Reverse side
1 
						

							2-76
COPIER
Contents
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the [Tab Copy] key.

Special modes menu (1st screen) (page 2-38)
3
Set the tab width.
(1) Set the image shift width (tab width) with 
the  keys.
0 mm to 20 mm (0 to 5/8) can be entered.
You can also directly touch a numeric value display key to 
change a number with the numeric keys.
(2) Touch the [OK] key.
You will return to the base screen of copy mode.
4
Load the tab paper.
When using the bypass tray, place the paper with the print side 
down. 
Place the paper so that the sides with the tabs enter the 
machine last.  
After loading the tab paper, configure the bypass tray settings 
as explained in MAKING COPIES USING THE BYPASS 
TRAY (page 2-35).
The width of the tab paper can be as wide as A4 width (210 mm) plus 20 mm (or 8-1/2 x 11 paper (8-1/2) plus 5/8).
5
Press the [START] key.
Copying will begin.
If you are using the document glass to copy multiple original pages, copying will take place as you scan each original. If you 
have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and then 
touch the [Read-End] key.
To cancel scanning and copying...
Press the [STOP] key ( ).
To cancel tab copy...
Touch the [Cancel] key in the screen of step 3.
System Settings (Administrator): Initial Tab Copy Setting
The default image shift width can be set from 0 mm to 20 mm (0 to 5/8). The factory default setting is 10 mm (1/2).
Special ModesOK
CancelOKTab Copy
10(0~20)
mm
Image ShiftCopyOriginal
(2)(1)
Reverse side 
						

							2-77
COPIER
Contents
COPYING BOTH SIDES OF A CARD ON ONE 
SHEET OF PAPER (Card Shot)
When copying a card, this function allows you to copy the front and reverse sides together onto a single sheet of paper.
This function is convenient for making copies for identification purposes and helps save paper.
1
Select the paper to be used for card 
shot.
Select the paper as explained in PAPER TRAYS (page 2-11).
2
Place the original face down on the 
document glass.
3
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the [Card Shot] key.

Special modes menu (1st screen) (page 2-38)
Front
BackOriginalsCopies
Example of an A4 
(8-1/2 x 11) size portrait copy
Example of an A4 (8-1/2  x  11) 
size landscape copy
Special Modes
2-Sided Copy
Output
File
Quick File
Copy Ratio
100%
OriginalPaper SelectAuto
A4
PlainAuto
ExposureAuto
Preview
A33.
1.2.A4A4RB44.
PlainA4 
						

							2-78
COPIER
Contents
4
Select card shot settings.
(1) Enter the original size.
With the [X] key highlighted, enter the X (horizontal) 
dimension of the original with the   keys.
Touch the [Y] key and enter the Y (vertical) dimension of 
the original with the   keys.
You can also directly touch a numeric value display key to 
change a number with the numeric keys.
(A) To enlarge or reduce the images to fit the paper 
based on the entered original size, touch the [Fit to 
Page] key.
(B) The [Size Reset] key can be pressed to return the 
horizontal and vertical dimensions to the values set in 
Card Shot Settings in the system settings 
(administrator).
(2) Touch the [OK] key.
You will return to the base screen of copy mode. Make 
sure that the entered dimensions appear in the [Original] 
key.
5
Press the [START] key to scan the front side of the card.
To cancel scanning...
Press the [STOP] key ( ).
6
Turn the card over and press the [START] key to scan the reverse side of the 
card.
Use the same [START] key that you used for the front side of the card.
To cancel scanning...
Press the [STOP] key ( ).
7
Touch the [Read-End] key.
Copying will begin.
To cancel copying...
Press the [STOP] key ( ).
Size Reset
(25~210)
mm
(25~210)
mm
X
Y
86
54
Special ModesOK
Card ShotOKCancel
Fit to
Page
(2)(1)
(A)
(B)
Read-End
Place next original. Press [Start].
When finished, press [Read-End]. 
						

							2-79
COPIER
Contents
 The original must be placed on the document glass.
 Copying is only possible on standard size paper.
 XY Zoom cannot be used when using this function.
 The image cannot be rotated when using this function.
To cancel card shot...
Touch the [Cancel] key in the screen of step 4.
System Settings (Administrator): Card Shot Settings
This is used to set the values to which the size returns when the [Size Reset] key is pressed. 25 mm to 210 mm (1 to 8-1/2) 
can be entered for both the horizontal and vertical dimensions.
The factory default settings are 86 mm (3-3/8) for X (the width) and 54 mm (2-1/8) for Y (the height). 
						

							2-80
COPIER
Contents
PRINTING THE DATE AND A STAMP ON 
COPIES (Stamp)
Use this function to print the date, a stamp, the page number, and text on copies. In addition, specific text can be added 
to a copy as a watermark. (Watermark)*
Six printing positions are available: top left, top centre, top right, bottom left, bottom centre, and bottom right.
The printing positions are separated into areas that are used for the date, page number and text (A below), and areas 
that are used for a stamp (B below). The watermark is printed at the centre of the paper.
* when equipped with the hard disk drive. 
When used in combination with other special modes
When Stamp is used in combination with the following special modes, the special modes are reflected in the stamp 
content.
BA
Top centre
Top right Top left
Bottom left Bottom right
Bottom centreWatermark 
print position
StampPrint areaMaximum number 
of positions
DateA1 position only
StampB6 positions
Page 
NumberingA1 position only
TextA6 positions
Watermark*Centre of 
paper—
 If the selected stamp content of one position overlaps the stamp content of another position, priority will be given in the 
following order: watermark, right side, left side, centre. Content that is hidden due to overlapping will not be printed.
 Text will be printed at the preset size regardless of the copy ratio or paper size setting.
 Text will be printed at the preset exposure regardless of the exposure setting.
 Depending on the size of the paper, some printed content may be cut off or shifted out of position.
Special ModesPrinting
Margin ShiftTogether with the image, the stamp content is shifted the amount of the margin width.
Tab Copy
CentringUnlike a copy image that moves, the image will be printed in the position set in the stamp.
Dual Page Copy
Card ShotThe stamp is printed on each copy sheet.
Multi ShotThe print content is printed on each original page.
Pamphlet Copy
Book CopyThe stamp is printed on each page of the resulting pamphlet or book.
Covers/InsertsUse the stamp settings to select whether or not the item is printed on inserted covers and 
inserts. 
						

							2-81
COPIER
Contents
GENERAL PROCEDURE FOR USING STAMP
To select stamp settings, follow the steps below.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Stamp] key.

Special modes menu (2nd screen) (page 2-39)
3
Select the print position.
Select from 6 positions: top left, top centre, top right, bottom 
left, bottom centre, bottom right.
You can also skip this step and go directly to the next step. In 
this case, the stamp items will be printed in the following 
positions:
Date: Top rightStamp: Top left
Page number: Bottom centreText: Top left
The position of a watermark cannot be selected. Proceed to the 
next step.
Print positions
The keys that show the print positions will appear as follows 
depending on the state of the settings.
The above key is the top left key. The appearance of each key 
varies depending on the position of the key.
 Date and Page Numbering cannot be selected in multiple positions. If the [Date] key or [Page Numbering] key is 
touched when Date or Page Numbering has already been selected for a position, a message will appear asking 
you if you wish to move that item to the selected position. To move the item, touch the [Yes] key. Otherwise, press 
the [No] key.
 If you attempt to set Date, Text, or Page Numbering in a position where one of these items is already set, a 
message will appear. To change the previously selected item to the new item, touch the [Yes] key. To keep the 
previous item, touch the [No] key.
OKSpecial Modes
StampOK
Layout
Cancel
Date
Page
NumberingText
Stamp
12
Watermark
Not selected, stamp setting has not
been selected.
Selected during selection of the stamp 
setting.
Not available, stamp setting has already 
been allocated. 
						

							2-82
COPIER
Contents
4
Select Stamp.
For detailed information on each of the stamp items, see the 
following sections:
Date:ADDING THE DATE TO COPIES (Date) 
(page 2-84)
Stamp: STAMPING COPIES (Stamp) (page 2-86)
Page numbering:PRINTING PAGE NUMBERS ON COPIES 
(Page Numbering) (page 2-88)
Text: PRINTING TEXT ON COPIES (Text) 
(page 2-92)
Watermark:ADDING A WATERMARK TO A COPY 
(Watermark) (page 2-98)
5
When you have finished selecting stamp 
settings, touch the   key.
6
Select settings for the original and 
covers/inserts.
(1) Touch the [Original Orientation] key and 
specify the orientation of the placed 
original.
If 2-sided originals have been placed, touch the   
key and specify the binding position (booklet binding or 
tablet binding) of the originals.
(2) Select stamp settings for covers/inserts.
If you do not want to print the stamp items on 
covers/inserts, touch the checkbox to remove the 
checkmark .
(3) Touch the [OK] key.
You will return to the base screen of copy mode.
To edit a stamp position or delete a stamp item, touch the 
[Layout] key.

CHECKING THE STAMP LAYOUT (Layout) (page 
2-96)
 When copying on covers/inserts is not selected, printing will not take place even if a checkmark appears.
 This setting cannot be selected if insertion of covers and inserts is disabled in the system settings (administrator).
OKSpecial Modes
StampOK
Layout
Cancel
Date
Page
NumberingText
Stamp
12
Watermark
OKSpecial Modes
StampOK
Layout
Cancel
Date
Page
NumberingText
Stamp
12
Watermark
Special ModesOK
OKStampCancel
Original Orientation
Print on Covers/Inserts when Copying on Covers/Inserts
2-Sided Original Type22
Layout
(2)(1)
(3)