Sharp Mxm264n User Guide

							2-103
COPIER
Contents
CREATING A LARGE POSTER (Multi-Page 
Enlargement)
This function is used to enlarge an image of an original and print it as a composite image using multiple sheets of paper.
1
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.
(4) Touch the [Multi-Page Enlargement] key.

[Image Edit] KEY (page 2-100)
Original 
(A4 (8-1/2 x 11) size)
Copy (enlarged image on 8 
sheets of A3 (11 x 17) paper) 
						

							2-104
COPIER
Contents
2
* The size that is twice A0 size.
Set the enlargement size and the original 
size.
(1) Select the size system that you wish to use 
for multi-page enlargement.
Touch the   keys to display the screen that shows 
the desired group of sizes.
 1st screen: A system
 2nd screen: B system
 3rd screen: Inch system
(2) Select the enlargement size.
(3) Select the size of the original to be used.
A suitable original placement orientation (A) and the 
number of sheets of paper required for the enlarged 
image (B) are displayed based on the selected original 
size and enlargement size.
Check the placement orientation and number of sheets.
The combinations of original sizes and enlargement sizes 
shown in the table at left are possible for multi-page 
enlargement.
 An A size original cannot be enlarged to a B size, and a B size original cannot be enlarged to an A size.
 To print a borderline around the copy image, touch the [Border Print] key so that it is highlighted.
3
Place the original face down on the 
document glass in the orientation 
indicated in the screen.
Ready to scan for copy. Copies will be
delivered in 2 parts.
OK
OKCancelBorder Print
Image Edit
Multi-Page Enlargement
A2
A4A1
A0
A0x2
A5
A3
Enlargement Size
(A Size)Original SizeOriginal Orientation13
(2)(A)(1)(3) (B)
A2                   A3, A4, A5
A1                   A3, A4, A5
A0                   A3, A4
A0 x 2*            A3
B3                   B4, B5
B2                   B4, B5
B1                   B4, B5
B0                   B4 
22 x 17       11 x 17, 8-1/2 x 14, 8-1/2 x 11
22 x 34       11 x 17, 8-1/2 x 14, 8-1/2 x 11
34 x 44       11 x 17, 8-1/2 x 14, 8-1/2 x 11
44 x 68       11 x 17
Enlargement size        Original size
Inch system
B system A system 
						

							2-105
COPIER
Contents
4
Touch the [OK] key.
You will return to the special modes screen. Touch the [OK] key 
to return to the base screen of copy mode.
5
Press the [START] key.
Copying will begin.
If you have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key.
To cancel scanning and copying...
Press the [STOP] key ( ).
 The original must be placed on the document glass.
 Overlap of sections of image
- There will be a margin around the edges of each copy.
- Areas for overlapping the copies will be created at the leading and trailing edges of each copy.
 If an original size is selected first, a message will appear indicating the enlargement sizes that can be selected. If an 
enlargement size is selected first, a message will appear indicating the original sizes that can be selected.
 If a combination of settings is selected for which multi-page enlargement is not possible, invalid selection beeps will sound.
 The paper size, number of sheets required for the enlarged image, and the ratio are automatically selected based on the 
selected original size and enlargement size. 
(The paper size and ratio cannot be selected manually.)
 If no paper trays have the size of paper that was automatically selected, Load XXX paper will appear. Change the paper 
in one of the trays or the bypass tray to the indicated size of paper.
To cancel the multi-page enlargement setting...
Touch the [Cancel] key in the screen of step 2.
Although the multi-page enlargement setting is cancelled, the ratio selected automatically is kept valid.
To return the ratio to 100%...
To return the ratio setting to 100%, touch the [Copy Ratio] key to display the ratio menu and then touch the [100%] key.
Original Orientation
OK
OKCancelBorder Print
Image Edit
Multi-Page Enlargement
Original Size13A2
A4A1
A0
A0x2
A5
A3
Enlargement Size
(A Size) 
						

							2-106
COPIER
Contents
REVERSING THE IMAGE (Mirror Image)
This feature is used to make a copy that is a mirror image of the original.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.

[Image Edit] KEY (page 2-100)
3
Select Mirror Image.
(1) Touch the [Mirror Image] key so that it is 
highlighted.
(2) Touch the [OK] key.
You will return to the special modes screen. Touch the 
[OK] key to return to the base screen of copy mode.
4
Press the [START] key.
Copying will begin.
If you are using the document glass to copy multiple original pages, copying will take place as you scan each original. If you have 
selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and then touch the 
[Read-End] key.
To cancel scanning and copying...
Press the [STOP] key ( ).
To cancel a mirror image setting...
Touch the [Mirror Image] key in the screen of step 3 so that it is not highlighted.
Original Mirror image copy
OK
Mirror
Image
B/W
Reverse
Multi-Page
Enlargement
Centring
Photo Repeat
OKSpecial Modes
Image Edit
(1)(2) 
						

							2-107
COPIER
Contents
COPYING IN THE CENTRE OF THE PAPER (Centring)
This is used to centre the copied image on the paper.
This lets you place the image in the centre of the paper when the original size is smaller than the paper size or when the 
image is reduced.
Not using the centring functionUsing the centring function
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.

[Image Edit] KEY (page 2-100)
3
Select Centring.
(1) Touch the [Centring] key so that it is 
highlighted.
(2) Touch the [OK] key.
You will return to the special modes screen. Touch the 
[OK] key to return to the base screen of copy mode.
4
Press the [START] key.
Copying will begin.
If you are using the document glass to copy multiple original pages, copying will take place as you scan each original. If you 
have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and then 
touch the [Read-End] key.
To cancel scanning and copying...
Press the [STOP] key ( ).
 The image can be reduced when using the centring function, but not enlarged.
 When the original size or the paper size is displayed as a special size, this function cannot be used.
To cancel centring...
Touch the [Centring] key in the screen of step 3 so that it is not highlighted.
OK
Mirror
Image
B/W
Reverse
Multi-Page
Enlargement
Centring
Photo Repeat
Special Modes
Image Edit
OK
(1)(2) 
						

							2-108
COPIER
Contents
REVERSING WHITE AND BLACK IN A COPY (B/W Reverse)
This is used to reverse black and white in a copy to create a negative image. This function can only be used for black 
and white copying.
Originals with large black areas (which use a large amount of toner) can be copied using Black/White Reverse to reduce 
toner consumption.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.

[Image Edit] KEY (page 2-100)
3
Select B/W Reverse.
(1) Touch the [B/W Reverse] key so that it is 
highlighted.
(2) Touch the [OK] key.
You will return to the special modes screen. Touch the 
[OK] key to return to the base screen of copy mode.
4
Press the [START] key.
Copying will begin.
If you are using the document glass to copy multiple original pages, copying will take place as you scan each original. If you 
have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and then 
touch the [Read-End] key.
To cancel scanning and copying...
Press the [STOP] key ( ).
 When this function is selected, the Original Image Type setting for exposure adjustment automatically changes to Text.
 This function is not available in some countries and regions.
To cancel B/W reverse...
Touch the [B/W Reverse] key in the screen of step 3 so that it is not highlighted.
Originals B/W Reverse copy
OK
Mirror
Image
B/W
Reverse
Multi-Page
Enlargement
Centring
Photo Repeat
Special Modes
Image Edit
OK
(1)(2) 
						

							2-109
COPIER
Contents
ADJUSTING THE SHARPNESS OF AN IMAGE (Sharpness)
This is used to sharpen an image or make it softer.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Sharpness] key.
3
Adjust the image.
(1) Touch the [Soft] key or the [Sharp] key.
(2) Touch the [OK] key.
You will return to the special modes screen. Touch the 
[OK] key to return to the base screen of copy mode.
4
Press the [START] key.
Copying will begin.
If you are using the document glass to copy multiple original pages, copying will take place as you scan each original. If you 
have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and then 
touch the [Read-End] key.
To cancel scanning and copying...
Press the [STOP] key ( ).
To cancel the sharpness setting...
Touch the [Cancel] key in the screen of step 3.
Soft
Sharp
OK
OKCancel
Special Modes
Sharpness
SharpSoft
(1)(2) 
						

							2-110
COPIER
Contents
CHECKING COPIES BEFORE PRINTING 
(Proof Copy)
This function requires the hard disk drive.
This feature prints only one set of copies, regardless of how many sets have been specified. After the first set is checked 
for errors, the remaining sets can be printed. Previously it was necessary to re-scan the original each time changes to 
settings were required. However, this feature makes it possible to change settings for the scanned original without 
scanning it again, allowing you perform copying more efficiently.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select copy settings in the base screen.
3
Select Proof Copy.
(1) Touch the [Special Modes] key.

SPECIAL MODES (page 2-38)
(2) Touch the   keys to switch through the 
screens.
(3) Touch the [Proof Copy] key so that it is 
highlighted.
(4) Touch the [OK] key.
AAAA
AAAA
AAAAAAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
If OK
After adjustments are 
made, 1 set is printed 
for you to checkThe remaining 4 sets 
are printed
Adjust the 
settings
If OK 1 set of copies is 
printed for you to 
check Proof Copy is 
selected and 5 sets of 
copies are executedThe remaining 4 
sets are printed
Special Modes
22
OK
Image Edit
Quick FileProof Copy
Sharpness
Slow Scan
ModeOriginal 
CountMixed Size
Original
Stamp
File
(4)(2)(3) 
						

							2-111
COPIER
Contents
4
Set the number of copies (number of 
sets) with the numeric keys.
If you will copy multiple originals using the document glass, 
switch to sort mode after this step.

Sort mode (page 2-32)
Up to 999 copies (sets) can be set.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
5
Press the [START] key.
One set of copies is printed.
If you are using the document glass to copy multiple originals, change originals and press the [START] key. Repeat until all 
pages have been scanned and then touch the [Read-End] key. One set of copies will be printed.
To cancel copying...
Press the [STOP] key ( ).
6
Check the printed set of copies. If the 
copies are acceptable, touch the [End] 
key. If you need to change the settings, 
touch the [Change] key.
When the [End] key is touched, the remaining sets are printed.
If you touched the [Change] key, go to the next step.
To cancel copying...
Press the [STOP] key ( ).
Plain
7
A4
Special Modes
2-Sided Copy
EndChange
Press [End] to continue.
To make a proof copy again, press
[Start]. 
						

							2-112
COPIER
Contents
7
Change the settings.
(1) Touch the key of the setting that you want 
to change.
The setting screen of the touched key opens. Change the 
settings and touch the [OK] key.
(2) Touch the [OK] key.
 To change the number of sets printed, set the desired number of copies (sets) with the numeric keys. After changing 
the number of sets, touch the [End] key in the touch panel (not the [START] key) to print the sets.
 Special modes that can be adjusted are Margin Shift, Pamphlet Copy, Tandem Copy, Covers/Inserts, Transparency 
Inserts, Multi-Shot, and Stamp.
 For Pamphlet Copy, Covers/Inserts, and Multi Shot, only changes to the settings of the functions can be made; the 
functions cannot be newly added or deleted.
 When transparency film is used, the settings can be changed, new settings can be added, and the function can be 
cancelled. However, this is not possible when pamphlet copying is enabled.
8
Press the [START] key.
One set of copies is printed again using the adjusted settings. Check the results. If further adjustments are needed, repeat 
steps 6 through 8. (Repeating Proof Copy does not decrease the remaining number of sets to be printed.)
9
Touch the [End] key.
You will return to the base screen of copy mode and the 
remaining sets will be printed.
To cancel scanning and copying...
Press the [STOP] key ( ).
If Proof Copy is executed while the machine is printing another job, the other job is interrupted and the proof copies are 
printed. The previous job will resume after the proof copies are printed.
However, if proof copy is executed during output of a job for which both two-sided printing and stapling are enabled, the proof 
copy will be output after the job in progress is finished. 
If the [End] key is touched to execute printing of the remaining sets while the machine is printing another job, the remaining 
sets will be printed after all previously reserved jobs are completed.
2-Sided CopyOutputPaper Select
Special Modes
OKProof Copy
(2)(1)
EndChange
Press [End] to continue.
To make a proof copy again, press
[Start].