Ricoh B230 Service Manual
Have a look at the manual Ricoh B230 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 127 Ricoh manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 386
B230/B237 5-20 SM
111 7 [Idling Time After Heater OFF]
After Ready *ENG
[0 to10 / 4 / 1 sec/step] DFU
001
Specifies the idling time without the lamp on after reaching the ready
temperature.
After Job End *ENG
[0 to10 / 4 / 1 sec/step]
002
Specifies the idling time without the lamp on after job end.
This idling prevents the heating roller overheating after job end.
11 5 9 [Fusing Jam Detection]
SC Display *ENG[0 or 1 / 0 / 1 /step]
0: Disable, 1: Enable
001
Enables or disables...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-385.png "Page 386
B230/B237 5-20 SM
111 7 [Idling Time After Heater OFF]
After Ready *ENG
[0 to10 / 4 / 1 sec/step] DFU
001
Specifies the idling time without the lamp on after reaching the ready
temperature.
After Job End *ENG
[0 to10 / 4 / 1 sec/step]
002
Specifies the idling time without the lamp on after job end.
This idling prevents the heating roller overheating after job end.
11 5 9 [Fusing Jam Detection]
SC Display *ENG[0 or 1 / 0 / 1 /step]
0: Disable, 1: Enable
001
Enables or disables...")
![Page 387
SM 5-21 B230/B237
Service
Tables
010 MCY Development: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
011 MCY Development: 138 *ENG
[–4 to 4 / 0 / 0.01 %/step]
012 MCY Development: 77 *ENG
[–4 to 4 / 0 / 0.01 %/step]
013 Fusing: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
014 Fusing: 138 *ENG
015 Fusing: 77 *ENG[–4 to 4 / 0.4 / 0.01 %/step]
016 Image Transfer: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
017 Image Transfer: 138 *ENG
[–4 to 4 / 0.3 / 0.01 %/step]
018 Image...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-386.png "Page 387
SM 5-21 B230/B237
Service
Tables
010 MCY Development: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
011 MCY Development: 138 *ENG
[–4 to 4 / 0 / 0.01 %/step]
012 MCY Development: 77 *ENG
[–4 to 4 / 0 / 0.01 %/step]
013 Fusing: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
014 Fusing: 138 *ENG
015 Fusing: 77 *ENG[–4 to 4 / 0.4 / 0.01 %/step]
016 Image Transfer: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
017 Image Transfer: 138 *ENG
[–4 to 4 / 0.3 / 0.01 %/step]
018 Image...")
![Page 388
B230/B237 5-22 SM
Counterclockwise
1907 [Paper Feed Timing Adj.] DFU
003 Feed Clutch OFF: Plain *ENG
[–10 to 10 / 0 / 1 mm/step]
004 Feed Clutch ON: Plain *ENG
[–10 to 10 / 0 / 1 mm/step]
005 Inverter Stop Position *ENG
[–10 to 10 / 0 / 1 mm/step]
006 Exit Stop Position: 3rd
Sheet *ENG
[–10 to 10 / 0 / 1 mm/step]
011 Entrance Stop Position *ENG
[–7 to 10 / 0 / 1 mm/step]
013 Feed Clutch OFF: Thick *ENG
[–10 to 10 / 0 / 1 mm/step]
014 Feed Clutch ON: Thick *ENG
[–10 to 10 / 0 /...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-387.png "Page 388
B230/B237 5-22 SM
Counterclockwise
1907 [Paper Feed Timing Adj.] DFU
003 Feed Clutch OFF: Plain *ENG
[–10 to 10 / 0 / 1 mm/step]
004 Feed Clutch ON: Plain *ENG
[–10 to 10 / 0 / 1 mm/step]
005 Inverter Stop Position *ENG
[–10 to 10 / 0 / 1 mm/step]
006 Exit Stop Position: 3rd
Sheet *ENG
[–10 to 10 / 0 / 1 mm/step]
011 Entrance Stop Position *ENG
[–7 to 10 / 0 / 1 mm/step]
013 Feed Clutch OFF: Thick *ENG
[–10 to 10 / 0 / 1 mm/step]
014 Feed Clutch ON: Thick *ENG
[–10 to 10 / 0 /...")
![Page 389
SM 5-23 B230/B237
Service
Tables
007 Feed Clutch ON: Thick *ENG
[–10 to 10 / 0 / 1 mm/step]
SP2-XXX (Drum)
2005 [Charge DC Voltage] Charge Roller DC Voltage Adjustment
(Paper Type, Process Speed, Color)
Paper Type –> Plain, Thick 1, Thick 2
Adjusts the DC component of the charge roller bias in the various print modes.
Charge bias (DC component) is automatically adjusted during process control;
therefore, adjusting these settings does not effect while process control mode
(SP3-041-1...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-388.png "Page 389
SM 5-23 B230/B237
Service
Tables
007 Feed Clutch ON: Thick *ENG
[–10 to 10 / 0 / 1 mm/step]
SP2-XXX (Drum)
2005 [Charge DC Voltage] Charge Roller DC Voltage Adjustment
(Paper Type, Process Speed, Color)
Paper Type –> Plain, Thick 1, Thick 2
Adjusts the DC component of the charge roller bias in the various print modes.
Charge bias (DC component) is automatically adjusted during process control;
therefore, adjusting these settings does not effect while process control mode
(SP3-041-1...")
![Page 390
B230/B237 5-24 SM
Charge bias (AC component) is adjusted by environment correction
(SP2-007-xxx to SP2-011-xxx). These SPs are activated only when SP2-012-1
is set to 1: manual control.
001 Plain: Bk *ENG
002 Plain: M *ENG
003 Plain: C *ENG
004 Plain: Y *ENG
005 Thick 1: Bk *ENG
006 Thick 1: M *ENG
007 Thick 1: C *ENG
008 Thick 1: Y *ENG
009 Thick 2&FINE: Bk *ENG
010 Thick 2&FINE: M *ENG
011 Thick 2&FINE: C *ENG
012 Thick 2&FINE: Y *ENG[0 to 3000 / 2100 / 10 V/step]
[Charge AC...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-389.png "Page 390
B230/B237 5-24 SM
Charge bias (AC component) is adjusted by environment correction
(SP2-007-xxx to SP2-011-xxx). These SPs are activated only when SP2-012-1
is set to 1: manual control.
001 Plain: Bk *ENG
002 Plain: M *ENG
003 Plain: C *ENG
004 Plain: Y *ENG
005 Thick 1: Bk *ENG
006 Thick 1: M *ENG
007 Thick 1: C *ENG
008 Thick 1: Y *ENG
009 Thick 2&FINE: Bk *ENG
010 Thick 2&FINE: M *ENG
011 Thick 2&FINE: C *ENG
012 Thick 2&FINE: Y *ENG[0 to 3000 / 2100 / 10 V/step]
[Charge AC...")
![Page 391
SM 5-25 B230/B237
Service
Tables
[Charge AC Current: ML] Charge Roller AC Current Adjustment for MM
(Color)
2008
Displays/sets the AC current target of the charge roller for ML environment
(Meddle temperature and Low humidity). DFU
001 Environmental Target: Bk *ENG
[0 to 3000 / 1040 / 10 μA/step]
002 Environmental Target: M *ENG
003 Environmental Target: C *ENG[0 to 3000 / 1030 / 10 μA/step]
004 Environmental Target: Y *ENG
[0 to 3000 / 1070 / 10 μA/step]
[Charge AC Current: MM]...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-390.png "Page 391
SM 5-25 B230/B237
Service
Tables
[Charge AC Current: ML] Charge Roller AC Current Adjustment for MM
(Color)
2008
Displays/sets the AC current target of the charge roller for ML environment
(Meddle temperature and Low humidity). DFU
001 Environmental Target: Bk *ENG
[0 to 3000 / 1040 / 10 μA/step]
002 Environmental Target: M *ENG
003 Environmental Target: C *ENG[0 to 3000 / 1030 / 10 μA/step]
004 Environmental Target: Y *ENG
[0 to 3000 / 1070 / 10 μA/step]
[Charge AC Current: MM]...")
![Page 392
B230/B237 5-26 SM
[Charge AC Current: HH] Charge Roller AC Current Adjustment for HH
(Color)
2011
Displays/sets the AC current target of the charge roller for HH environment
(High temperature and High humidity). DFU
001 Environmental Target: Bk *ENG
[0 to 3000 / 940 / 10 μA/step]
002 Environmental Target: M *ENG
003 Environmental Target: C *ENG[0 to 3000 / 930 / 10 μA/step]
004 Environmental Target: Y *ENG
[0 to 3000 / 960 / 10 μA/step]
2012 [Charge Output Control]
001 AC Voltage...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-391.png "Page 392
B230/B237 5-26 SM
[Charge AC Current: HH] Charge Roller AC Current Adjustment for HH
(Color)
2011
Displays/sets the AC current target of the charge roller for HH environment
(High temperature and High humidity). DFU
001 Environmental Target: Bk *ENG
[0 to 3000 / 940 / 10 μA/step]
002 Environmental Target: M *ENG
003 Environmental Target: C *ENG[0 to 3000 / 930 / 10 μA/step]
004 Environmental Target: Y *ENG
[0 to 3000 / 960 / 10 μA/step]
2012 [Charge Output Control]
001 AC Voltage...")
![Page 393
SM 5-27 B230/B237
Service
Tables
1: LL, 2: ML, 3: MM, 4: MH, 5: HH
003 Absolute Humidity:
Threshold 1 *ENGChanges the humidity threshold between
LL and ML.
[0 to 100 / 4.3 / 0.01 g/m
3/step]
004 Absolute Humidity:
Threshold 2 *ENGChanges the humidity threshold between
ML and MM.
[0 to 100 / 11 . 3 / 0.01 g/m
3/step]
005 Absolute Humidity:
Threshold 3 *ENGChanges the humidity threshold between
MM and MH.
[0 to 100 / 18.0 / 0.01 g/m
3/step]
006 Absolute Humidity:
Threshold 4...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-392.png "Page 393
SM 5-27 B230/B237
Service
Tables
1: LL, 2: ML, 3: MM, 4: MH, 5: HH
003 Absolute Humidity:
Threshold 1 *ENGChanges the humidity threshold between
LL and ML.
[0 to 100 / 4.3 / 0.01 g/m
3/step]
004 Absolute Humidity:
Threshold 2 *ENGChanges the humidity threshold between
ML and MM.
[0 to 100 / 11 . 3 / 0.01 g/m
3/step]
005 Absolute Humidity:
Threshold 3 *ENGChanges the humidity threshold between
MM and MH.
[0 to 100 / 18.0 / 0.01 g/m
3/step]
006 Absolute Humidity:
Threshold 4...")
![Page 394
B230/B237 5-28 SM
[Color Registration Correction] FA
2101 These values are the parameters for the automatic line position adjustment and
are adjusted at the factory. However, you must input a value for SP2101-001
after replacing the laser optics housing unit. For details, see Laser Optics
Housing Unit in the Replacement and Adjustment section. The value should
be provided with the new laser optics housing unit.
001 Main Dot: Bk *ENG
002 Main Dot: M *ENG
003 Main Dot: C *ENG
004...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-393.png "Page 394
B230/B237 5-28 SM
[Color Registration Correction] FA
2101 These values are the parameters for the automatic line position adjustment and
are adjusted at the factory. However, you must input a value for SP2101-001
after replacing the laser optics housing unit. For details, see Laser Optics
Housing Unit in the Replacement and Adjustment section. The value should
be provided with the new laser optics housing unit.
001 Main Dot: Bk *ENG
002 Main Dot: M *ENG
003 Main Dot: C *ENG
004...")
![Page 395
SM 5-29 B230/B237
Service
Tables
006 Main Mag.: Low Speed:
M *ENG
007 Main Mag.: High Speed:
C *ENG
008 Main Mag.: Medium
Speed: C *ENG
009 Main Mag.: Low Speed: C *ENG
010 Main Mag.: High Speed:
Y *ENG
011 Main Mag.: Medium
Speed: Y *ENG
012 Main Mag.: Low Speed: Y *ENG
2103 [Erase Margin Adjustment] (Area, Paper Size)
Adjusts the erase margin by changing the activation timing of the registration
clutch.
001 Lead Edge Width *ENG
002 Trail. Edge Width *ENG[0 to 9.9 / 4.2 / 0.1...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-394.png "Page 395
SM 5-29 B230/B237
Service
Tables
006 Main Mag.: Low Speed:
M *ENG
007 Main Mag.: High Speed:
C *ENG
008 Main Mag.: Medium
Speed: C *ENG
009 Main Mag.: Low Speed: C *ENG
010 Main Mag.: High Speed:
Y *ENG
011 Main Mag.: Medium
Speed: Y *ENG
012 Main Mag.: Low Speed: Y *ENG
2103 [Erase Margin Adjustment] (Area, Paper Size)
Adjusts the erase margin by changing the activation timing of the registration
clutch.
001 Lead Edge Width *ENG
002 Trail. Edge Width *ENG[0 to 9.9 / 4.2 / 0.1...")
![Page 396
B230/B237 5-30 SM
2105 [LD Power Adj.] (Process Speed, Color)
Displays the LD power of each color for each process speed.
Each LD power setting is decided by process control.
001 High Speed: Bk *ENG
002 High Speed: M *ENG
003 High Speed: C *ENG
004 High Speed: Y *ENG
005 Middle Speed: Bk *ENG
006 Middle Speed: M *ENG
007 Middle Speed: C *ENG
008 Middle Speed: Y *ENG
009 Low Speed: Bk *ENG
010 Low Speed: M *ENG
011 Low Speed: C *ENG
012 Low Speed: Y...](http://img.usermanuals.tech/thumb/64/100811/w64_b230-service-manual-1509630901_d-395.png "Page 396
B230/B237 5-30 SM
2105 [LD Power Adj.] (Process Speed, Color)
Displays the LD power of each color for each process speed.
Each LD power setting is decided by process control.
001 High Speed: Bk *ENG
002 High Speed: M *ENG
003 High Speed: C *ENG
004 High Speed: Y *ENG
005 Middle Speed: Bk *ENG
006 Middle Speed: M *ENG
007 Middle Speed: C *ENG
008 Middle Speed: Y *ENG
009 Low Speed: Bk *ENG
010 Low Speed: M *ENG
011 Low Speed: C *ENG
012 Low Speed: Y...")
SM 5-25 B230/B237 Service Tables [Charge AC Current: ML] Charge Roller AC Current Adjustment for MM (Color) 2008 Displays/sets the AC current target of the charge roller for ML environment (Meddle temperature and Low humidity). DFU 001 Environmental Target: Bk *ENG [0 to 3000 / 1040 / 10 μA/step] 002 Environmental Target: M *ENG 003 Environmental Target: C *ENG[0 to 3000 / 1030 / 10 μA/step] 004 Environmental Target: Y *ENG [0 to 3000 / 1070 / 10 μA/step] [Charge AC Current: MM] Charge Roller AC Current Adjustment for MM (Color) 2009 Displays/sets the AC current target of the charge roller for MM environment (Middle temperature and Middle humidity). DFU 001 Environmental Target: Bk *ENG [0 to 3000 / 980 / 10 μA/step] 002 Environmental Target: M *ENG 003 Environmental Target: C *ENG[0 to 3000 / 960 / 10 μA/step] 004 Environmental Target: Y *ENG [0 to 3000 / 1000 / 10 μA/step] [Charge AC Current: MH] Charge Roller AC Current Adjustment for MH (Color) 2010 Displays/sets the AC current target of the charge roller for MH environment (Middle temperature and High humidity). DFU 001 Environmental Target: Bk *ENG [0 to 3000 / 960 / 10 μA/step] 002 Environmental Target: M *ENG 003 Environmental Target: C *ENG[0 to 3000 / 940 / 10 μA/step] 004 Environmental Target: Y *ENG [0 to 3000 / 970 / 10 μA/step]
B230/B237 5-26 SM [Charge AC Current: HH] Charge Roller AC Current Adjustment for HH (Color) 2011 Displays/sets the AC current target of the charge roller for HH environment (High temperature and High humidity). DFU 001 Environmental Target: Bk *ENG [0 to 3000 / 940 / 10 μA/step] 002 Environmental Target: M *ENG 003 Environmental Target: C *ENG[0 to 3000 / 930 / 10 μA/step] 004 Environmental Target: Y *ENG [0 to 3000 / 960 / 10 μA/step] 2012 [Charge Output Control] 001 AC Voltage *ENGSelects the AC voltage control type. [0 or 1 / 0 / 1/step] 0: Process control 1: Manual control (AC voltages are decided with SP2006.) 2013 [Environmental Correction: PCU] 001 Current Environmental: Display *ENGDisplays the environmental condition, which is measured in absolute humidity. [1 to 5 / – / 1 /step] 1: LL (LL
SM 5-27 B230/B237 Service Tables 1: LL, 2: ML, 3: MM, 4: MH, 5: HH 003 Absolute Humidity: Threshold 1 *ENGChanges the humidity threshold between LL and ML. [0 to 100 / 4.3 / 0.01 g/m 3/step] 004 Absolute Humidity: Threshold 2 *ENGChanges the humidity threshold between ML and MM. [0 to 100 / 11 . 3 / 0.01 g/m 3/step] 005 Absolute Humidity: Threshold 3 *ENGChanges the humidity threshold between MM and MH. [0 to 100 / 18.0 / 0.01 g/m 3/step] 006 Absolute Humidity: Threshold 4 *ENGChanges the humidity threshold between MH and HH. [0 to 100 / 24.0 / 0.01 g/m 3/step] 007 Current Temp.: Display *ENGDisplays the current temperature. [0 to 100 / – / 1°C/step] 008 Current Relative Humidity: Display *ENGDisplays the current relative humidity. [0 to 100 / – / 1%/step] 009 Current Absolute Humidity: Display *ENGDisplays the absolute humidity. [0 to 100 / – / 0.01 g/m3/step] 010 Previous Environmental: Display *ENGDisplays the previous environmental condition, which is measured in absolute humidity. [1 to 5 / – / 1 /step] 1: LL, 2: ML, 3: MM, 4: MH, 5: HH 011 Previous Temp.: Display *ENGDisplays the previous temperature. [0 to 100 / – / 1°C/step] 012 Previous Relative Humidity: Display *ENGDisplays the previous relative humidity. [0 to 100 / – / 1%/step] 013 Previous Absolute Humidity: Display *ENGDisplays the previous absolute humidity. [0 to 100 / – / 0.01 g/m3/step]
B230/B237 5-28 SM [Color Registration Correction] FA 2101 These values are the parameters for the automatic line position adjustment and are adjusted at the factory. However, you must input a value for SP2101-001 after replacing the laser optics housing unit. For details, see Laser Optics Housing Unit in the Replacement and Adjustment section. The value should be provided with the new laser optics housing unit. 001 Main Dot: Bk *ENG 002 Main Dot: M *ENG 003 Main Dot: C *ENG 004 Main Dot: Y *ENG[–512 to 511 / 0 / 1 dot/step] 005 Subdot: Bk *ENG 006 Subdot: M *ENG 007 Subdot: C *ENG 008 Subdot: Y *ENG[–16384 to 16383 / 0 / 1 line/step] 2102 [Magnification Adjustment] DFU 001 Main Mag.: High Speed: Bk *ENG 002 Main Mag.: Medium Speed: Bk *ENG 003 Main Mag.: Low Speed: Bk *ENG 004 Main Mag.: High Speed: M *ENG 005 Main Mag.: Medium Speed: M *ENGThese are results of the main scan length adjustment. [0 to 560 / 280 / 1 /step]
SM 5-29 B230/B237 Service Tables 006 Main Mag.: Low Speed: M *ENG 007 Main Mag.: High Speed: C *ENG 008 Main Mag.: Medium Speed: C *ENG 009 Main Mag.: Low Speed: C *ENG 010 Main Mag.: High Speed: Y *ENG 011 Main Mag.: Medium Speed: Y *ENG 012 Main Mag.: Low Speed: Y *ENG 2103 [Erase Margin Adjustment] (Area, Paper Size) Adjusts the erase margin by changing the activation timing of the registration clutch. 001 Lead Edge Width *ENG 002 Trail. Edge Width *ENG[0 to 9.9 / 4.2 / 0.1 mm/step] 003 Left *ENG 004 Right *ENG[0 to 9.9 / 2 / 0.1 mm/step] 005 Lead Edge Width: Thin *ENG [0 to 9.9 / 5 / 0.1 mm/step] 006 Duplex Trail. L Size *ENG 007 Duplex Trail. M Size *ENG 008 Duplex Trail. S Size *ENG[0 to 4 / 0 / 0.1 mm/step] 009 Duplex Left Edge *ENG 010 Duplex Right Edge *ENG[0 to 1.5 / 0.3 / 0.1 mm/step]
B230/B237 5-30 SM 2105 [LD Power Adj.] (Process Speed, Color) Displays the LD power of each color for each process speed. Each LD power setting is decided by process control. 001 High Speed: Bk *ENG 002 High Speed: M *ENG 003 High Speed: C *ENG 004 High Speed: Y *ENG 005 Middle Speed: Bk *ENG 006 Middle Speed: M *ENG 007 Middle Speed: C *ENG 008 Middle Speed: Y *ENG 009 Low Speed: Bk *ENG 010 Low Speed: M *ENG 011 Low Speed: C *ENG 012 Low Speed: Y *ENG[50 to 120 / 100 / 1%/step] Decreasing a value makes lines thinner on the output. Increasing a value makes lines thicker on the output. 2106 [Polygon Rotation Time] Adjusts the time of the polygon motor rotation. DFU 001 Warming-Up *ENG 002 Job End *ENG[0 to 60 / 10 / 1 sec/step] [Image Parameter] 2107 DFU 001 Image Gamma Flag *ENG [0 or 1 / 1 / 1 /step]
SM 5-31 B230/B237 Service Tables 002 Shading Correction Flag *ENG [0 or 1 / 1 / 1 /step] [Test Pattern] 2109 Generates the test pattern using COPY Window tab in the LCD. 003 Pattern Selection - [0 to 23 / 0 / 1/step] 0 None 1: 1-dot line pattern (Vertical) 2: 2-dot line pattern (Vertical) 3: 1-dot line pattern (Horizontal) 4: 2-dot line pattern (Horizontal) 5: 1-dot grid pattern (Vertical) 6: 1-dot grid pattern (Horizontal) 7: 1-dot grid pattern (Fine) 8: 1-dot grid pattern (Rough) 9: 1-dot slant pattern (Fine) 10: 1-dot slant pattern (Rough) 11. 1-dot pattern 12. 2-dot pattern 13. 4-dot pattern 14. 1-dot trimming pattern 15: None 16: Cross stitch: main-scan 17: Belt pattern (Horizontal) 18: Belt pattern (Vertical) 19: Checkered flag 20: Gray scale (Vertical) 21: Gray scale (Horizontal) 22: None 23: Solid 005 Color Selection - Specifies the color for the test pattern. [1 to 4 / 1 / 1/step] 1: All colors, 2: Magenta, 3: Yellow, 4: Cyan 006 Density: Bk - Specifies the color density for the test
B230/B237 5-32 SM 007 Density: M - 008 Density: C - 009 Density: Y - pattern. [0 to 15 / 15 / 1 /step] 0: Lightest density 15: Darkest density 2111 [Forced Line Position Adj.] 001 Mode a - Executes the fine line position adjustment twice. If this SP is not completed (NG is displayed), do SP2111-003 first and then try this SP again. 002 Mode b - Executes the fine line position adjustment once. If this SP is not completed, do SP2111-003 first and then try this SP again. 003 Mode c - Executes the rough line position adjustment once. After doing this SP, make sure to execute SP2111-001 or -002. Otherwise, the line position adjustment is not perfectly done. 2112 [TM/ID Sensor Check] ID Sensor Check FA 001 Execute This SP is used to check the ID sensors at the factory. The results of this SP are displayed in SP2140 to SP2145. [Skew Adjustment] 2117 Specifies a skew adjustment value for the skew motor M, C or Y. These SPs must be used when a new laser optics housing unit is installed or when SC285 occurs. For details, see Laser Optics Housing Unit in the Replacement and Adjustment section.
SM 5-33 B230/B237 Service Tables 001 Pulse: M *ENG 002 Pulse: C *ENG 003 Pulse: Y *ENG[–100 to 100 / 0 / 1 pulse/step] 2118 [Skew Adjustment] 001 Pulse: M *ENG 002 Pulse: C *ENG 003 Pulse: Y *ENGChanges the current skew adjustment values to the values specified with SP2117. These SPs must be used when a new laser optics housing unit is installed or when SC285 occurs. For details, see Laser Optics Housing Unit in the Replacement and Adjustment section. [Skew Adjustment Display] 2119 Displays the current skew adjustment value for each skew motor. 001 M *ENG 002 C *ENG 003 Y *ENG[–50 to 50 / 0 / 1 pulse/step] [ID Sensor Check Result] DFU 2140 Displays the results of the ID sensor check. Bk, M, C, Y: ID sensors for the process control Front, Center, Rear: ID sensors for the automatic line position adjustment 001 Bk *ENG 002 M *ENG 003 C *ENG 004 Y *ENG[0 to 1024 / - / 1/step]
B230/B237 5-34 SM 005 Front *ENG 006 Center *ENG 007 Rear *ENG [ID Sensor Check Result: Ave.] DFU 2141 Displays the average result values of the ID sensor check. Bk, M, C, Y: ID sensors for the process control Front, Center, Rear: ID sensors for the automatic line position adjustment 001 Bk *ENG 002 M *ENG 003 C *ENG 004 Y *ENG 005 Front *ENG 006 Center *ENG 007 Rear *ENG[0 to 5 / 0 / 0.01V/step] [ID Sensor Check Result] DFU 2142 Displays the maximum result values of the ID sensor check. Bk, M, C, Y: ID sensors for the process control Front, Center, Rear: ID sensors for the automatic line position adjustment 001 Maximum: Bk *ENG 002 Maximum: M *ENG 003 Maximum: C *ENG 004 Maximum: Y *ENG 005 Maximum: Front *ENG[0 to 5 / 0 / 0.01V/step]