Home > Ricoh > Printer > Ricoh B230 Service Manual

Ricoh B230 Service Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Ricoh B230 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 127 Ricoh manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1286
    Add page 231 to Favourites
    image text
    Enable zoom 
    							 
SM 3-103 B230/B237 
Replacement 
Adjustment 
 
3.  SIO board with bracket [B] (
 x 4, All s) 
3.14.8  HIGH VOLTAGE SUPPLY BOARD 
 
1.  Rear cover (
 Rear Cover) 
2.  High voltage supply board [A] (
 x 6, All s,  x 1)
    Add page 232 to Favourites
    image text
    Enable zoom 
    							 
B230/B237 3-104  SM 
3.14.9  HIGH VOLTAGE SUPPLY BOARD BRACKET 
 
1.  Rear cover (
 Rear Cover) 
2.  Remove all the connectors and release the clamp [A]. 
 
3.  Release all the clamps [B]. 
4.  Open out the high voltage supply board bracket [C] (
  x 3) and then remove it.
    Add page 233 to Favourites
    image text
    Enable zoom 
    							 
SM 3-105 B230/B237 
Replacement 
Adjustment 
3.14.10 CONTROLLER  BOARD 
 
1.  Controller unit (
 Controller Box) 
2.  Fan bracket [A] and grip [B] (
 x 1,  x 1) 
3.  Controller board [C] (
 x 7,  x 2) 
 
4.  Interface rails [D], NV-RAM [E] and RAM-DIMM(s) [F] 
When installing the new BICU 
Remove the NVRAM from the old controller board. Then install it on the new controller 
board after you replace the controller board. Replace the NVRAM (
 NVRAM 
Replacement Procedure) if the NVRAM on the old controller board is defective. 
 
ƒ  Make sure you print out the SMC reports (“SP Mode Data” and “Logging Data”) 
before you replace the NVRAM.
    Add page 234 to Favourites
    image text
    Enable zoom 
    							 
B230/B237 3-106  SM 
 
ƒ  Keep NVRAMs away from any objects that can cause static electricity. Static 
electricity can damage NVRAM data. 
ƒ  Make sure the NVRAM is correctly installed on the controller board.   
ƒ  Make sure that the DIP-switch settings on the old controller board are the same for 
the new controller board. Do not change the DIP switches on the controller board 
in the field. 
3.14.11 HDD 
 
1.  Controller unit (
 Controller Box) 
2.  HDD unit [A] (
 x 4,  x 2) 
 
3.  HDD unit upper cover [B] and lower cover [C] (
 x 5) 
4. HDD [D] 
5.  Turn the main switch on. The disk is automatically formatted.
    Add page 235 to Favourites
    image text
    Enable zoom 
    							 
SM 3-107 B230/B237 
Replacement 
Adjustment 
6.  Install the stamp data using SP5853. 
7.  Switch the machine off and on to enable the fixed stamps for use. 
Disposal of HDD Units 
ƒ  Never remove an HDD unit from the work site without the consent of the client. 
ƒ  If the customer has any concerns about the security of any information on the HDD, 
the HDD must remain with the customer for disposal or safe keeping. 
ƒ  The HDD may contain proprietary or classified (Confidential, Secret) information. 
Specifically, the HDD contains document server documents and data stored in 
temporary files created automatically during copy job sorting and jam recovery. Such 
data is stored on the HDD in a special format so it cannot normally be read but can be 
recovered with illegal methods. 
Reinstallation 
Explain to the customer that the following information stored on the HDD is lost when the 
HDD is replaced: 
ƒ  Document server documents 
ƒ Custom-made stamps 
ƒ  Document server address book 
The address book and document server documents (if needed) must be input again.   
If the customer is using the Data Overwrite Security feature, the DOS function must be set 
up again. For more, see Section 1 (Installation). 
If the customer is using the optional Browser Unit, this unit must be installed again. For 
more, see Section 1 (Installation). 
3.14.12 NVRAM  REPLACEMENT PROCEDURE 
NVRAM on the BICU 
1.  Make sure that you have the SMC report (factory settings). This report comes 
with the machine. 
2.  Output the SMC data (
  SP5-990-001) if possible. 
3.  Turn the main switch off. 
4.  Install an SD card into SD card slot 3. Then turn the main power on. 
5.  Copy the NVRAM data to an SD card (
  SP5-824-001) if possible. 
6.  Turn off the main switch. Then unplug the power cord. 
7.  Replace the NVRAM on the BICU and reassemble the machine. 
8.  Plug in the power cord. Then turn the main switch on. 
9.  Select a paper-size type (
 SP5-131-001). 
10.  Specify the device number and destination code of the machine.
    Add page 236 to Favourites
    image text
    Enable zoom 
    							 
B230/B237 3-108  SM 
 
ƒ  Contact your supervisor for details on how to enter the device number and 
destination code. 
ƒ  SC 999 or “Fusing Unit Setting Error” can be shown until the device number 
and destination code are correctly programmed. 
11.  Turn the main switch off and on. 
12.  Copy the data from the SD card to the NVRAM (
  SP5-825-001) if you have 
successfully copied them to the SD card. 
13.  Turn the main switch off. Then remove the SD card from SD card slot 3. 
14.  Turn the main switch on. 
15.  Specify the SP and UP mode settings. 
16.  Do the process control self-check. 
17.  Do ACC for the copier application program. 
18.  Do ACC for the printer application program. 
NVRAM on the Controller 
 
ƒ  If you change the NVRAM in the controller, and the Data Overwrite Security unit is 
installed, this Data Overwrite Security unit must be replaced with a new one. 
1.  Make sure that you have the SMC report (factory settings). This report comes 
with the machine. 
2.  Output the SMC data (
  SP5-990-001) if possible. 
3.  Turn the main switch off. Then put a blank formatted SD card into SD card slot 3. 
4.  Turn the main switch on. 
5.  Copy the NVRAM data (
  SP5-824-001) and the address book data in the HDD 
( SP5846-051) to an SD card if possible. 
 
ƒ  An error message shows if local user information cannot be stored in an SD 
card because the capacity is not enough. 
ƒ  You cannot do this procedure if the SD card is write-protected. 
6.  Enter SP mode. Then print out the SMC reports (
  SP5-990-001) if possible. 
7.  Turn off the main switch. Then unplug the power cord. 
8.  Replace the NVRAM on the controller. Then reassemble the machine. 
9.  Check if the serial number shows on the operation panel. (SP5-811-002). Input 
the serial number if it does not show. (Contact your supervisor about this 
setting.) 
10.  Plug in the power cord. Then turn the main switch on.
    Add page 237 to Favourites
    image text
    Enable zoom 
    							 
SM 3-109 B230/B237 
Replacement 
Adjustment 
11.  Copy the data from the SD card to the NVRAM (  SP5-825-001) and HDD 
(SP5-846-52) if you have successfully copied them to the SD card. 
 
ƒ  The counter data in the user code information clears even if step 11 is done 
correctly. 
ƒ  An error message shows if the download is incomplete. However, you can still 
use the part of the address book data that has already been downloaded in 
step 11. 
ƒ  An error message shows when the download data does not exist in the SD 
card, or, if it is already deleted. 
ƒ  You cannot do this procedure if the SD card is write-protected. 
12.  Go out of SP mode. Then turn the main switch off. Then remove the SD card 
from SD card slot 3. 
13.  Turn the main switch on. 
14.  Specify the SP and UP mode settings. 
15.  Do ACC for the copier application program. 
16.  Do ACC for the printer application program.
    Add page 238 to Favourites
    Enable zoom
    Add page 239 to Favourites
    image text
    Enable zoom 
    							 
 
 
 
 
 
TROUBLESHOOTING
    Add page 240 to Favourites
    Enable zoom
    All Ricoh manuals Comments (0)

    Related Manuals for Ricoh B230 Service Manual