NEC Neax 2400 Ipx System Operations And Maintenance Manual
Have a look at the manual NEC Neax 2400 Ipx System Operations And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 698
CHAPTER 8 NDA-24307
Page 670
Issue 1
MBCT: Make Busy of Connection Trunk for LDM
MBCT:Make Busy of Connection Trunk for LDM
1. Functional Outline
This command is used to set/reset the make busy state of the connection trunk.
2. Parameters
Input data
C_RT: Connection Route Number [1-1023]
C_TK: Trunk Number [1-4095]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy (Outgoing)](http://img.usermanuals.tech/thumb/54/84234/w64_nec-ipx-system-op-and-maint-ipx-u-type_d-697.png "Page 698
CHAPTER 8 NDA-24307
Page 670
Issue 1
MBCT: Make Busy of Connection Trunk for LDM
MBCT:Make Busy of Connection Trunk for LDM
1. Functional Outline
This command is used to set/reset the make busy state of the connection trunk.
2. Parameters
Input data
C_RT: Connection Route Number [1-1023]
C_TK: Trunk Number [1-4095]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy (Outgoing)")
NDA-24307 CHAPTER 8 Page 673 Issue 1 MBRT: Make Busy of Route MBRT:Make Busy of Route 1. Functional Outline This command assigns Idle/Busy status for all the trunks in the route designated. 2. Parameters Input data RT: Route Number of the external route/internal route. The Internal Route Number and its meaning is shown in the table below. MB: 0/1=Make Idle/Make Busy DATA MEANING DATA MEANING 901 Attendant/Desk Console 902 Originating Register Trunk 903 Incoming Register Trunk 904 MF Receiver 905 Sender Trunk DP/PB 906 PB Receiver for Automated Attendant Service 907 AMP 908 Not used 909 Three-Way Conference Trunk 910-912 Not used 913 Three-Way Conference Trunk for ATTCON 914 Not used 915 Night Attendant Console 916 MFC Register 917 MFC Sender 918 Not used 919-926 Modem 927, 928 Not used 929 Data Signaling Trunk-Option 930 Rate Adapter Conversion Trunk 931-947 Not used
CHAPTER 8 NDA-24307 Page 674 Issue 1 MBSM: Make Busy of System Message Printout MBSM:Make Busy of System Message Printout 1. Functional Outline This command allows or inhibits the system message printer to output system messages. 2. Parameters Input data PORT NO.: Port Number of the printer MB: 0/1=Make Idle/Busy
NDA-24307 CHAPTER 8 Page 675 Issue 1 MBST: Make Busy of Station MBST:Make Busy of Station 1. Functional Outline This command assigns the Idle/Busy status of stations. 2. Parameters Input data TN STN: Maximum 5 digits for Business system/maximum 6 digits for Hotel system. MB: 0/1=Make Idle/Make Busy
CHAPTER 8 NDA-24307 Page 676 Issue 1 MBST_T: Make Busy of Station - Telephone Number MBST_T:Make Busy of Station - Telephone Number 1. Functional Outline This command is used to assign the IDLE/BUSY status of stations, by using Telephone Numbers. This com- mand is available at NCN (for Fusion network) only. Note 1 Note 1: This command is available for PBX program software. 2. Parameters Input Data UGN: User Group Number TELN: Telephone Number (max. 16 digits) MB: Make Busy/Make Idle Display Data FPC: Fusion Point Code (1-253) Note 2 TN: Tenant Number Note 2 STN: Physical Station Number (max. 5 digits for Business system/max. 6 digits for Hotel system) Note 2 Note 2: This data is for display only. Buttons Get: Click to get information on the station Set: Click to execute the BUSY/IDLE performance. Exit: Click to exit this command.
NDA-24307 CHAPTER 8 Page 677 Issue 1 MBTC: Make Busy of Trunk-Continuous MBTC:Make Busy of Trunk-Continuous 1. Functional Description This command is used to assign the IDLE/BUSY status of trunks. By using this command, plural trunks can be placed into IDLE/BUSY state simultaneously per a route designated in “RT” parameter. 2. Parameters RT: R o u t e N u m b e r TK: Trunk Number Note 1 MB: 0=Make Idle 1=Make Busy(Outgoing) 2=Make Busy (Bothway) Note 2 Note 1: Plural trunks can be assigned simultaneously per a route designated in “RT” parameter. Note 2:2=Make Busy (Bothway) is not used.
CHAPTER 8 NDA-24307 Page 678 Issue 1 MBTK: Make Busy of Trunk MBTK:Make Busy of Trunk 1. Functional Outline This command assigns the Idle/Busy status of trunks. 2. Parameters RT: R o u t e N u m b e r TK: Trunk Number MB: 0=Make Idle 1=Make Busy (Outgoing)
NDA-24307 CHAPTER 8 Page 679 Issue 1 MEM_HDD: Data Control Between Memory and HDD MEM_HDD:Data Control Between Memory and HDD 1. Functional Outline This command is used to save the following data from MEM of PBX to HDD of PBX, and vice versa. 2. Parameters Input data Direction Select: Memory to Hard Disk/Hard Disk to Memory/Verify HDD against MEM Data Type Selection: Data Memory Note 1 Name Display Wireless Call Forwarding Call Forwarding Speed Calling User Assign Soft Key Number Sharing Note 2 Call Block ACD Data Memory LP Select: This data is valid when Call Forwarding, Speed Calling, User Assign Soft Key, Number Sharing or Call Block data is designated. Auto Verify Afterward Note 1:When “Data Memory” is selected, Local Data Memory (LDM) and Network Data Memory (NDM) are also saved/verified simultaneously. Note 2:By saving the Number Sharing data, the data concerning “Dual Station Calling Over-FCCS is also saved/verified automatically.
CHAPTER 8 NDA-24307 Page 680 Issue 1 MEM_HDD_N: Data Control Between Memory and HDD for NDM MEM_HDD_N:Data Control Between Memory and HDD for NDM 1. Functional Outline This command, available at the NCN only, is used to save/verify a series of Office Data from the Memory of all Local Nodes to the HDD of the same node. 2. Parameters Input data Direction Select: MEM to HDD/Verify HDD against MEM Data Type Selection: Data Memory Note 1 Name Display Wireless Call Forwarding Call Forwarding Speed Calling User Assign Soft Key Number Sharing Note 2 Call Block ACD Data Memory LP Select: The parameter is valid when Call Forwarding, Speed Calling, User Assign Soft Key, Number Sharing, or Call Block data is designated. Auto Verify Afterward Note 1:When “Data Memory” is selected, Local Data Memory (LDM) and Network Data Memory (NDM) are also saved/verified simultaneously. Note 2:By saving the Number Sharing data, the data concerning “Dual Station Calling Over-FCCS is also saved/verified automatically. Display data Information: FPC of Node in which saving/verifying is executed Result of the execution Direction: MEM to HDD/Verify HDD against MEM Data Type: Selected Data Type
NDA-24307 CHAPTER 8 Page 681 Issue 1 MFCH: Make Busy of FCCH MFCH:Make Busy of FCCH 1. Functional Outline This command is used to set or reset the make busy state of the FCH card. 2. Parameters Input data FCHN: FCH Number [1-255] MB: Make Busy Information [0/1] 0=Make Idle 1=Make Busy
CHAPTER 8 NDA-24307 Page 682 Issue 1 PMBU: Port Microprocessor Back Up PMBU:Port Microprocessor Back Up 1. Functional Outline This command saves the contents of Port Microprocessor (PM) onto Floppy Disk (FD) or verifies them. Information of firmware (Program Code) also appears on the screen. 2. Parameters Input data Direction Select: Port Microprocessor to MAT/Verify Port Microprocessor/Verify PM with Error List Auto Verify Afterward can be performed when designating Port Microprocessor to MAT. PM Information: Module Group/Unit/Group/Data Size(1-6) See the following data: 1=2 Kbytes 2=4 Kbytes 3=8 Kbytes 4=16Kbytes 5=32Kbytes 6=64Kbytes Display data Office SP Number: Information of firmware (Program Code) SP Issue: Information of firmware (Program Code)