NEC Neax 2400 Ipx System Operations And Maintenance Manual
Have a look at the manual NEC Neax 2400 Ipx System Operations And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 530
CHAPTER 6 NDA-24307
Page 502
Issue 1
SYSTEM OPERATIONS
10.1 Designated Connection Test (Station)
(1) General
The purpose of this test is to confirm the operations related to a trunk or tone that is designated from the
test station. Refer to Ta b l e 6 - 6. The test result displays on the MAT screen as system message [6-I].
(2) Precaution
Designated connection to a trunk—A designated connection to trunk is limited only to an individual line
of either 2nd DT system or sender system.
Table 6-6 Designated...](http://img.usermanuals.tech/thumb/54/84234/w64_nec-ipx-system-op-and-maint-ipx-u-type_d-529.png "Page 530
CHAPTER 6 NDA-24307
Page 502
Issue 1
SYSTEM OPERATIONS
10.1 Designated Connection Test (Station)
(1) General
The purpose of this test is to confirm the operations related to a trunk or tone that is designated from the
test station. Refer to Ta b l e 6 - 6. The test result displays on the MAT screen as system message [6-I].
(2) Precaution
Designated connection to a trunk—A designated connection to trunk is limited only to an individual line
of either 2nd DT system or sender system.
Table 6-6 Designated...")
NDA-24307 CHAPTER 6 Page 503 Issue 1 SYSTEM OPERATIONS (3) Designated Connection Test Procedure (a) Register Test Procedure Figure 6-29 Register Test Procedure/Connection Diagram Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 Route numbers to be designated are as follows.: If any of the dialed numbers are not received correctly, a Reorder Tone (ROT) is heard. RT NUMBER 902 903 TRUNK NAME Originating Register Trunk Incoming Register Trunk Hang Up TRUNK DESIGNATIONTEST IN PROGRESS REGISTER UNDER TEST ORT Note: If the Trunk Number of the next register is not assigned, the test ends. Lift handset (DT) Dial access code for designated connection (DT) Dial “1,2,3,4,5,6,7,8,9,0” (*, # in case of PB signal) consecutively Is next register to be tested, too?(NO) (YES) Make switch hook flash Note + “9xx” RT No.“xxx” TRK No. (SST)
CHAPTER 6 NDA-24307 Page 504 Issue 1 SYSTEM OPERATIONS (b) Sender Test Procedure Figure 6-30 Sender Test Procedure/Connection Diagram Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 Route number to be designated is as follows: If any of the dialed numbers are received correctly, a Reorder Tone (ROT) is heard. RT NUMBER 905 TRUNK NAME Sender Trunk DP/PB Note 1:After the sender to be tested is connected to the register, the sender sends out 1 ~ 9, 0 by DP signals and 1 ~ 9, 0, *, # by PB signals, thus checking to see if the dialed numbers are sent out correctly. Note 2:If the trunk number of the next sender is not assigned, the test ends. + “9xx” RT No.“xxx” TRK No. Lift handset Connection test is automatically Is next performed Note 1 register to be tested, too? Make switch hook flash Note 2 (DT) Dial access code for designated connection (Music On Hold) (SST) TRUNK DESIGNATION MUSIC ON HOLD ORT SNDTEST IN PROGRESS ORT DP OR PB YESNO Hang Up
NDA-24307 CHAPTER 6 Page 505 Issue 1 SYSTEM OPERATIONS (c) 3-Party Conference Trunk Test Procedure Figure 6-31 3-Party Conference Test Procedure Note:If the trunk number of the next 3-Party Conference Trunk is not assigned, the test ends. Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 Route numbers to be designated are as follows: RT NUMBER 909 913 TRUNK NAME 3-party conference trunk (for station, ATTCON, trunk) 3-party conference trunk (only for ATTCON) + “9xx” RT No.“xxx” TRK No. Lift handset Is next register to be tested, too? Make switch hook flash Note (DT) Dial access code for designated connection (SST) (SST) YESNO Hang Up As shown in Figure 6-32, tone sending is repeated.
CHAPTER 6 NDA-24307 Page 506 Issue 1 SYSTEM OPERATIONS Figure 6-32 3-Party Conference Test Connection Diagram TSTT TSTT TSTTTSTT TSTT TSTT ORTSST TRUNK DESIGNATION TEST IN PROGRESS 1 SEC.1 SEC.1 SEC.1 SEC. 1 SEC. 1 SEC. 1 SEC. 1 SEC. (DT) (SST) (DT) (SST) (DT) (SST)
NDA-24307 CHAPTER 6 Page 507 Issue 1 SYSTEM OPERATIONS (d) Tone Test Procedure Figure 6-33 Tone Test Procedure/Connection Diagram Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 For Tone No. to be designated, refer to Table 6-7. Tone designated by Tone No. is heard. Lift handset (Tone) Dial access code for designated connection Dial “x x” Tone Number Dial “000” (DT) Hang Up(DT)TRUNK DESIGNATIONTEST IN PROGRESS ORT ORTTONE
CHAPTER 6 NDA-24307 Page 508 Issue 1 SYSTEM OPERATIONS Table 6-7 Tone Numbers Tone No. Kind Of Tone Remarks 00 Dial Tone (DT) 01 Special Dial Tone (SPDT) 02 Ring Back Tone (RBT) 03Continuous Ring Back Tone (CRBT) 04 Busy Tone (BT) 05 Reorder Tone (ROT) 06 Service Set Tone (SST) 07 Second Dial Tone (SDT) 08 No Tone 09 Sender Transmitting Tone (SDTT) 10 Call Waiting Ring Back Tone (CWRBT) 11 No Tone 12 No Tone 1 3 Te s t To n e ( T S T T ) 14 Music On Hold (MSC) 15 No Tone
NDA-24307 CHAPTER 6 Page 509 Issue 1 SYSTEM OPERATIONS (e) Interrupt Ringing (IR) Test Procedure Figure 6-34 Interrupt Ringing (IR) Test Procedure/Connection Diagram AAA A ORTIR SST Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 Lift handset Dial access code for designated connection (SST) (DT) TEST IN PROGRESSDESIGNATION Dial “999” Hang Up Bell Rings Lift handset and answer (SST) Hang Up HANGUPSST ANSWER
CHAPTER 6 NDA-24307 Page 510 Issue 1 SYSTEM OPERATIONS (f) Trunk Test Procedure Figure 6-35 Trunk Test Procedure Note:If the trunk number of the next trunk is not assigned, the test ends. Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 + “9xx” RT No.“xxx” TRK No. Lift handset Is next register to be tested, too? Make switch hook flash Note (DT) Dial access code for designated connection (RBT) YESNO Dial the called party number The called party at the distant office answers and talks Hang Up
NDA-24307 CHAPTER 6 Page 511 Issue 1 SYSTEM OPERATIONS Figure 6-36 Trunk Test Connection Diagram A ORT TRUNK DESIGNATIONCALLED PARTY DIALINGCALLED PARTY DIALING NUMBER SENDINGCALLED PARTY DIALING TRKA AA A A2nd DT SYSTEM CHARGING SERVICE PROVIDED SENDER SYSTEM SND TRK ORT ORT TRK
CHAPTER 6 NDA-24307 Page 512 Issue 1 SYSTEM OPERATIONS 10.2 Designated Connection Test (DESKCON/ATTCON) (1) General The purpose of this test is to confirm the operations related to a trunk which has been designated from the DESKCON/ATTCON. (2) Test Procedure (a) Trunk seizure with TKSL key Whether dialing RT No. + TRK No. OR Dialing C.O. Line NO. is determined per ASYD command, SYS1. INDEX68. b1. C.O. Line No. is assigned by ACOC command. Press TKSL or TRKSL key (RBT) + “xxx” RT No.“xxx” TRK No. or “xxxx” C.O. Line NO. Dial the called party number Press CANCEL key The called party at the and talks distant office answers(DT from Distant Office)