NEC Neax 2400 Ipx System Operations And Maintenance Manual
Have a look at the manual NEC Neax 2400 Ipx System Operations And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24307 CHAPTER 4 Page 273 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE Figure 4-3 How to Replace the CPU ..... ..... 12 34 567 812 34 567 812 345A SLOT No. 0 1 2 3 45 6 26E ..... ..... 12 34 567 812 34 567 8 12 345A SLOT No. 0 1 2 3 4 5 6 26E CPR LPM IMG 0
CHAPTER 4 NDA-24307 Page 274 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE Replacement Procedure Note:ACT/STBY of CPR can also be performed by using the CMODI/CMOD command. For details, refer to Chapter 8, Maintenance Commands. System Changeover of the CPU from AC T to ST B Y m od e. IMG0 lamp on the DSP begin to flash green. Check the mate CPU’s lamp indications: At the ISW CPU OPE=Steady green IMG0 ~ IMG3=Steady green at the LN CPU OPE=Steady green IMG0 ~ IMG3=Flash green Note: IMG2 - IMG3 lamps may be OFF depending on the system configuration EMA SUP lamp on the EMA card lights green. Cable Name to be disconnected CPU 0: 10AL-(110) FLT CA CPU 1: 10AL-(130) FLT CA START Make a backup copy of the main data (office data, CF/SPD data, etc.) onto the hard disk of the HFD. Turn ON the MBR key on the DSP of the CPU to be replaced. Then turn OFF the MBR key again. Confirm the mate CPUs ACT mode. Turn ON the EMA SUP key on the EMA (PH-PC40) card. Disconnect the power alarm cable from the PALM connector on PZ-PW92. A IMG1 IMG2 IMG3 CPUOPE WDT IMG0 12 34 567 8 OFF 12 34 567 8 OFF 12 34 OFF MBR FRONT VIEWDSP ON 4C026AE AT T E N T I O NContents Static Sensitive Handling Precautions Required PWR (PZ-PW92) FRONT VIEW SW ON OFF PALM -48V ON ALM OUTPWR INPWR
NDA-24307 CHAPTER 4 Page 275 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE ATTENTIONContents Static Sensitive Handling Precautions Required Refer to Figure 4-2 for CPR face layout. Refer to Figure 4-2 for CPR face layout. Refer to Figure 4-3 to replace the CPU. Cables to be disconnected Ether cable: UTP CTG5 ST CA-n Note: The kind of Ethernet cable may vary, Disconnect power cables from the OUTPWR connector and INPWR connector on PZ-PW92. Disconnect Ethernet cables from the front connectors on the PZ-PC19 (LANI). Remove the four screws fastened onto the CPR. (Keep the removed screws.) B A Turn OFF the SW key on PZ-PW92. Disconnect bus cables from the front connectors on the PZ-GT13/PZ-GT20 (ISAGT). Cables to be disconnected from front EXGT BUS CA-A for CN-M connector depending on its connecting conditions. Cable to be disconnected from OUTPWR CPU 0: 6P-(4P-3P) PWR CA-A CPU 1: 6P-(4P-3P) PWR CA-B Cable to be disconnected from INPWR CPU 0: 4P-2P PWR CA-A CPU 1: 4P-2P PWR CA-B PWR (PZ-PW92) FRONT VIEW SW ON OFF PALM -48V ON ALM OUTPWR INPWR connector of PZ-GT13 34PH 50AL CA-A for CN-T connector 34PH 50AL CA-B (in LN only) Cables to be disconnected from front connector of PZ-GT20
CHAPTER 4 NDA-24307 Page 276 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE ATTENTIONContents Static Sensitive Handling Precautions Required Refer to Figure 4-3 to replace the CPU. Refer to Circuit Card Installation Into New CPR procedure in this section.C B Extract the CPR from the LPM. Mount the ISAGT (PZ-GT13/PZ-GT20) and LANI (PZ-PC19) cards onto the new CPR. Then, insert the new CPR into the LPM.
NDA-24307 CHAPTER 4 Page 277 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE ATTENTIONContents Static Sensitive Handling Precautions Required Note: Do not connect the cable for the Connect the disconnected bus cables to the front connectors on the PZ-GT13/PZ-GT20. Turn ON the SW key on PZ-PW92. Connect the disconnected power alarm cable to the PALM connector on PZ-PW92. D C Connect the disconnected Ethernet cables Connect the disconnected power cables to the OUTPWR and INPWR connectors. PALM connector yet. to the connectors on the PZ-PC19. PWR (PZ-PW92) FRONT VIEW SW ON OFF PALM -48V ON OUTPWR INPWR ALM
CHAPTER 4 NDA-24307 Page 278 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE ATTENTIONContents Static Sensitive Handling Precautions Required EMA SUP lamp on the EMA card goes OFF. IMG0 lamp on the DSP flashes green. Flip the MBR key on the DSP of the new CPR from ON to OFF. END D Turn OFF the EMA-SUP key on the EMA (PH-PC40) card. Confirm that IPL has completed successfully. Initial Program Load (IPL) starts automatically. MBR(DSP) IMG1 IMG2 IMG3 CPUOPE WDT IMG0 12 34 567 8 OFF 12 34 567 8 OFF 12 34 OFF MBR FRONT VIEWDSP ON 4C026AE
NDA-24307 CHAPTER 4 Page 279 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE Circuit Card Installation Into New CPR This procedure shows how to install the new CPR into the LPM. (1) Detach the front panel of the new CPR by using the Phillips screwdriver to remove the four screws, as shown in Figure 4-4. Then, lift the top cover by removing the eight screws. Figure 4-4 Removal of Front Panel and Top Cover From CPR ATTENTIONContents Static Sensitive Handling Precautions Required Top Cover CPRFront Panel
CHAPTER 4 NDA-24307 Page 280 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE (2) Insert the ISAGT (PZ-GT13/PZ-GT20) and LANI (PZ-PC19) cards into the following slots of the new CPR (refer to Figure 4-5): ISAGT (PZ-GT13) →Slot 6 (ISA) ISAGT (PZ-GT20) →Slot 5 (ISA) (When LN has more than two IMGs) Note LANI (PZ-PC19) →Slot 0 (PCI) (For Fusion Link) LANI (PZ-PC19) →Slot 1 (PCI) (When connecting MAT via 10-BASE T and PCI buses) LANI (PZ-PC19) →Slot 3 (PCI) (When LANI for Fusion Link is in dual configuration) Figure 4-5 shows how to insert the ISAGT and LANI cards into the PCI slots 5 and 6, 0 and 1 and 3 of the CPR, respectively. Note:This card is mounted in LN only. Figure 4-5 Insertion of ISAGT and LANI Cards ATTENTIONContents Static Sensitive Handling Precautions Required CPR Slot 6 (ISA) ISAGT LANI Slot 5 (ISA) Slot 3 (PCI)Slot 1 (PCI)Slot 0 (PCI) Note:Actual installation of the LANI card may differ, depending on your system configuration.
NDA-24307 CHAPTER 4 Page 281 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE (3) Reattach the top cover by fastening the removed eight screws. Then, reattach the front panel by fastening the removed four screws. Refer to Figure 4-6). Figure 4-6 Reattachment of CPR Top Cover and Front Panel ATTENTIONContents Static Sensitive Handling Precautions Required Top Cover CPRFront Panel
CHAPTER 4 NDA-24307 Page 282 Issue 1 UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE (4) After turning ON the MBR key on the DSP of the new CPR, insert the new CPR into the LPM as shown in Figure 4-7. Then, fasten the retained four screws. Figure 4-7 Accommodation of New CPR Into LPM ATTENTIONContents Static Sensitive Handling Precautions Required CPR LPM