NEC Neax 2400 Imx System Operations And Maintenance Manual
Have a look at the manual NEC Neax 2400 Imx System Operations And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 632
NDA-24238 CHAPTER 8
Page 605
Revision 3.0
MAINTENANCE COMMANDS
MFCH:Make Busy of FCCH
1. Functional Outline
This command is used to set or reset the make busy state of the FCH card.
2. Parameters
Input Data
FCHN: FCH Number [1-255]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy](http://img.usermanuals.tech/thumb/54/84348/w64_nec-neax2400-imx-system-operations-and-maintenance-manual_d-631.png "Page 632
NDA-24238 CHAPTER 8
Page 605
Revision 3.0
MAINTENANCE COMMANDS
MFCH:Make Busy of FCCH
1. Functional Outline
This command is used to set or reset the make busy state of the FCH card.
2. Parameters
Input Data
FCHN: FCH Number [1-255]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy")
CHAPTER 8 NDA-24238 Page 604 Revision 3.0 MAINTENANCE COMMANDS MEM_HDD_N:Data Control Between Memory and HDD for NDM 1. Functional Outline This command, available at the NCN only, is used to save/verify a series of Office Data from the Memory of all Local Nodes to the HDD of each same node. 2. Parameters Input data Direction Select: MEM to HDD Verify HDD against MEM Data Type Selection: Data Memory Note 1 Name Display Wireless Call Forwarding Call Forwarding Speed Calling User Assign Soft Key Number Sharing Note 2 Call Block (for software Release 5 or later) LP Select: The parameter is valid when Call Forwarding, Speed Calling, User Assign Soft Key, Number Sharing or Call Block data is designated. Auto Verify Afterward Note 1:When Data Memory is selected, Network Data Memory (NDM) and Local Data Memory (LDM) are also saved/verified simultaneously. Note 2:By saving the Number Sharing data, the data concerning Dual Station Calling Over-FCCS (available for Release 5 or later software) is also saved/verified automatically. Display data Information: FPC of Node in which saving/verifying is executed Result of the execution Direction: MEM to HDD Verify HDD against MEM Data Type: Selected Data Type
NDA-24238 CHAPTER 8 Page 605 Revision 3.0 MAINTENANCE COMMANDS MFCH:Make Busy of FCCH 1. Functional Outline This command is used to set or reset the make busy state of the FCH card. 2. Parameters Input Data FCHN: FCH Number [1-255] MB: Make Busy Information [0/1] 0=Make Idle 1=Make Busy
CHAPTER 8 NDA-24238 Page 606 Revision 3.0 MAINTENANCE COMMANDS PMBU:Port Microprocessor Back Up 1. Functional Outline This command saves the contents of Port Microprocessor (PM) onto Floppy Disk (FD) or verifies them. Information of firmware (Program Code) also appears on the screen. 2. Parameters Input data Direction Select: Port Microprocessor to MAT Verify Port Microprocessor Verify PM with Error List Auto Verify Afterward can be performed when desig- nating Port Microprocessor to MAT. PM Information: Module Group Unit Group Data Size (1-6) 1=2 Kbytes 2=4 Kbytes 3=8 Kbytes 4=16 Kbytes 5=32 Kbytes 6=64 Kbytes Display data Office SP Number: Information of firmware (Program Code) SP Issue: Information of firmware (Program Code)
NDA-24238 CHAPTER 8 Page 607 Revision 3.0 MAINTENANCE COMMANDS RALM:Release Alarm 1. Functional Outline This command clears the fault indications. 2. Parameters Input data WRT: Y=Alarm is released N=Not released RETURN TO MENU?: Y=Return to MENU N=Start operation again Display data Alarms Released
CHAPTER 8 NDA-24238 Page 608 Revision 3.0 MAINTENANCE COMMANDS RALMN:Release Alarm for NDM 1. Functional Outline This command, available at the NCN only, clears the fault indications of all the Nodes by clicking the release button on the display. 2. Parameters Display data FPC: FPC of alarm released Nodes Status: Result of releasing the alarm OK/NG
NDA-24238 CHAPTER 8 Page 609 Revision 3.0 MAINTENANCE COMMANDS RLST:Release Station/Trunk 1. Functional Outline This command releases a station or trunk. 2. Parameters Input data TYPE: Type of Select (1-4) 1=Stations 2=Trunk 3=LENS 4=Connection Trunk TN: Note 1 STN: Maximum 6 digits Note 1 RT:Note 2 TK:Note 2 LENS:Note 3 Connection RT: (1-1023) Note 4 Connection TK: (1-4095) Note 4 Note 1: This parameter is valid only when TYPE=1. Note 2:This parameter is valid only when TYPE=2. Note 3:This parameter is valid only when TYPE=3. Note 4:This parameter is valid only when TYPE=4. Display data STATUS: Status of Station/Trunk (1-4) 1=Idle 2=Busy 3=Lockout 4=Make Busy FPC: Fusion Point Code (1-253) INFORMATION: Information of the connected party Note Note: This parameter appears only when STATUS=2.
CHAPTER 8 NDA-24238 Page 610 Revision 3.0 MAINTENANCE COMMANDS RLST_T:Release of Station/Trunk – Telephone Number 1. Functional Outline This command is used to release a station/trunk, by using Telephone Numbers. This command is available at NCN (for Fusion network) only. 2. Parameters Input Data TYPE: Telephone Number Trunk LENS Connection Trunk UGN: User Group Number Note 1 TELN: Telephone Number (max. 16 digits)Note 1 RT: External/Internal Route Number Note 2 TK: Trunk Number Note 2 LENS: Line Equipment Number Note 3 C_RT: Connection Route Number (1-1023) Note 4 C_TK: Connection Trunk Number (1-4095) Note 4 Note 1: This parameter is valid when “Telephone Number” is designated in the “TYPE” selection list box. Note 2:This parameter is valid when “Trunk” is designated in the “TYPE” selection list box. Note 3:This parameter is valid when “LENS” is designated in the “TYPE” selection list box Note 4:This parameter is valid when “Connection Trunk” is designated in the “TYPE” selection list box. Display Data FPC: Fusion Point Code (1-253) TN: Tenant Number Note 5 STN: Physical Station Number (max. 5 digits for Business/max. 6 digits for Hotel system) Note 5 Note 5: This data is displayed when “Telephone Number” is designated in the “TYPE” selection list box.
NDA-24238 CHAPTER 8 Page 611 Revision 3.0 MAINTENANCE COMMANDS STATUS: Status of Station/Trunk (1-5) 1=Idle 2=Busy 3=Lockout 4=Make Busy 5=Now Calling INFORMATION: Information on the connected party Note 6 ERN: Area Number (1-32) Note 7 GRN: Group Number (1-8) Note 7 CSN/ZTN: CS/ZT Number (1-32) Note 7 PCN: PHS Community Number (1-1024) Note 7 Note 6: This data is displayed when “STATUS” =2 (Busy). Note 7:This data is for Wireless System only. Buttons Get: Click to get information on the station/trunk. Release: Click to execute the station/trunk release. Exit: Click to exit this command.
CHAPTER 8 NDA-24238 Page 612 Revision 3.0 MAINTENANCE COMMANDS SINZ:System Initialization 1. Functional Outline This command initializes the PBX from the MAT. At the time of system initialization, this command allows the programs and the office data to be loaded from a Hard Disk of PBX into the RAM of PBX. 2. Parameters Input data TYPE: Kind of Initialization (1-4) 1=System Initialize 2=System Initialize Office Data Load & System Initialize 3=System Initialize Program Load & System Initialize 4=System Initialize Program & Office Data Load & System Initialize Note:When the system is initialized, the MAT is once disconnected. Then, log in to the system again.
NDA-24238 CHAPTER 8 Page 613 Revision 3.0 MAINTENANCE COMMANDS SPTS:Scanning of Port Status 1. Functional Outline This command displays momentarily the working status of Port Microprocessor (PM) on Module Group (MG), Unit, and Group basis. 2. Parameters Input data MG Unit Group Interval: Unit for this parameter is in seconds. Entry Procedure Type 1: By MG Display of Scanning by Designating MG (Figure 8-1) Package Status PM: Not Mounted Note ID: Idle at least one BY: All Busy MB: Under Make Busy Status Note:This information appears when the circuit card is in make busy status (MB key is set upward) or when the designated location has no circuit card.