NEC Neax 2400 Imx System Operations And Maintenance Manual
Have a look at the manual NEC Neax 2400 Imx System Operations And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 616
NDA-24238 CHAPTER 8
Page 589
Revision 3.0
MAINTENANCE COMMANDS
HDD_FDD:Data Control Between HDD and FDD
1. Functional Outline
This command is used to install the program data from FDD of PBX to HDD of PBX, and to verify the program
data between FDD of PBX and HDD of PBX.
2. Parameters
Input data [When system uses software Release 1 or 2]
System Select: HFD0
HFD1
Direction Select: Floppy Disk to Hard Disk
Verify HDD against FDD
Note:Hard Disk to Floppy Disk cannot be selected.
Data Type Selection:...](http://img.usermanuals.tech/thumb/54/84348/w64_nec-neax2400-imx-system-operations-and-maintenance-manual_d-615.png "Page 616
NDA-24238 CHAPTER 8
Page 589
Revision 3.0
MAINTENANCE COMMANDS
HDD_FDD:Data Control Between HDD and FDD
1. Functional Outline
This command is used to install the program data from FDD of PBX to HDD of PBX, and to verify the program
data between FDD of PBX and HDD of PBX.
2. Parameters
Input data [When system uses software Release 1 or 2]
System Select: HFD0
HFD1
Direction Select: Floppy Disk to Hard Disk
Verify HDD against FDD
Note:Hard Disk to Floppy Disk cannot be selected.
Data Type Selection:...")
CHAPTER 8 NDA-24238 Page 584 Revision 3.0 MAINTENANCE COMMANDS DTF303N:Display of UCD Station Peg Count Data for Fusion Network 1. Functional Outline This command is used for displaying the result of traffic measurement data for “Type”=10 (UCD Station Peg Count) assigned by the ATRFN command. 2. Parameters Traffic Data 1: Terminal Traffic-DTF101N Route Traffic-DTF102N Station Peg Count-DTF103N Attendant Peg Count-DTF104N Route Peg Count-DTF105N Traffic Data 2: Service Peg Count-DTF201N Traffic Data 3: UCD Route Peg Count-DTF301N UCD Group Peg Count-DTF302N UCD Station Peg Count-DTF303N Traffic Data 5: Attendant Ans. Peg Count-DTF501N Traffic Data 6: Connection Route Peg Count-DTF601N Connection Route Traffic-DTF602N
NDA-24238 CHAPTER 8 Page 585 Revision 3.0 MAINTENANCE COMMANDS DTF501N:Display of Attendant Answering Peg Count Data for Fusion Network 1. Functional Outline This command is used for displaying the result of traffic measurement data for “Type”=15 (ATT Answering Peg Count) assigned by the ATRFN command. 2. Parameters Traffic Data 1: Terminal Traffic-DTF101N Route Traffic-DTF102N Station Peg Count-DTF103N Attendant Peg Count-DTF104N Route Peg Count-DTF105N Traffic Data 2: Service Peg Count-DTF201N Traffic Data 3: UCD Route Peg Count-DTF301N UCD Group Peg Count-DTF302N UCD Station Peg Count-DTF303N Traffic Data 5: Attendant Ans. Peg Count-DTF501N Traffic Data 6: Connection Route Peg Count-DTF601N Connection Route Traffic-DTF602N
CHAPTER 8 NDA-24238 Page 586 Revision 3.0 MAINTENANCE COMMANDS DTF601N:Display of Connection Route Peg Count Data for Fusion Network 1. Functional Outline This command is used for displaying the result of traffic measurement data for “Type”=18 (Connection Route Peg Count) assigned by the ATRFN command. 2. Parameters Traffic Data 1: Terminal Traffic-DTF101N Route Traffic-DTF102N Station Peg Count-DTF103N Attendant Peg Count-DTF104N Route Peg Count-DTF105N Traffic Data 2: Service Peg Count-DTF201N Traffic Data 3: UCD Route Peg Count-DTF301N UCD Group Peg Count-DTF302N UCD Station Peg Count-DTF303N Traffic Data 5: Attendant Ans. Peg Count-DTF501N Traffic Data 6: Connection Route Peg Count-DTF601N Connection Route Traffic-DTF602N
NDA-24238 CHAPTER 8 Page 587 Revision 3.0 MAINTENANCE COMMANDS DTF602N:Display of Connection Route Traffic Data for Fusion Network 1. Functional Outline This command is used for displaying the result of traffic measurement data for “Type”=19 (Connection Route Traffic) assigned by the ATRFN command. 2. Parameters Traffic Data 1: Terminal Traffic-DTF101N Route Traffic-DTF102N Station Peg Count-DTF103N Attendant Peg Count-DTF104N Route Peg Count-DTF105N Traffic Data 2: Service Peg Count-DTF201N Traffic Data 3: UCD Route Peg Count-DTF301N UCD Group Peg Count-DTF302N UCD Station Peg Count-DTF303N Traffic Data 5: Attendant Ans. Peg Count-DTF501N Traffic Data 6: Connection Route Peg Count-DTF601N Connection Route Traffic-DTF602N
CHAPTER 8 NDA-24238 Page 588 Revision 3.0 MAINTENANCE COMMANDS FLINST:File Install 1. Functional Outline This command is used to install the DPSW-dedicated database files to your MAT. This command is necessary to provide each circuit card’s various information (such as circuit card name, equipped switch names, etc.) when your system uses the DPSW/DPKG command. 2. Parameters Input Data None Buttons Copy: Click to start the data file install. Exit: Click to exit this command. (1) Start up the FLINST command from the Start menu. (2) Initial Display of the FLINST command appears. Make sure the proper FD drive name is selected in the FDD parameter. (3) Click the Copy button. Then, a message, requiring to insert the first FD into the FDD drive, appears. (4) Insert the first FD into the FDD of the MAT. Then, click OK. (5) File copy starts automatically, and the Copy End message appears upon completion. (6) Click OK. Another message asks you whether the next FD is to be installed or not. (7) Click OK. (8) A message, requiring you to insert the second FD into the FDD drive is displayed. Insert the second FD into the FDD, and click OK. (9) File copy starts automatically, and the Copy End message appears upon completion. (10) Click OK. A message asks you whether the next (fourth) FD is to be installed or not. (11) Click Cancel.
NDA-24238 CHAPTER 8 Page 589 Revision 3.0 MAINTENANCE COMMANDS HDD_FDD:Data Control Between HDD and FDD 1. Functional Outline This command is used to install the program data from FDD of PBX to HDD of PBX, and to verify the program data between FDD of PBX and HDD of PBX. 2. Parameters Input data [When system uses software Release 1 or 2] System Select: HFD0 HFD1 Direction Select: Floppy Disk to Hard Disk Verify HDD against FDD Note:Hard Disk to Floppy Disk cannot be selected. Data Type Selection: Program data (others are invalid.) LP Select: Not used Auto Verify Afterward Input data [When system uses software Release 3 or later] System Select: HFD0 HFD1 Direction Select: Floppy Disk to Hard Disk Verify HDD against FDD Hard Disk to Floppy Disk Data Type Selection: Data Memory Note 1 Name Display Wireless Call Forwarding Program data Note 2 Call Forwarding Speed Calling User Assign Soft Key
CHAPTER 8 NDA-24238 Page 590 Revision 3.0 MAINTENANCE COMMANDS Number Sharing Note 3 Call Block ACD Data Memory LP Select: This data appears when Call Forwarding, Speed Calling, User Assign Soft Key, Number Sharing or Call Block data is designated. File Name Select Auto Verify Afterward Note 1:When Data Memory is selected, Network Data Memory (NDM) and Local Data Memory (LDM) are also saved/verified simultaneously. Note 2:Program data can be valid when Floppy Disk to Hard Disk option or Verify HDD against FDD option in the Direction Select list box is selected. Note 3:By saving the Number Sharing data, the data concerning Dual Station Calling Over-FCCS is also saved/verified automatically.
NDA-24238 CHAPTER 8 Page 591 Revision 3.0 MAINTENANCE COMMANDS HDD_MAT:Data Control Between HDD and MAT 1. Functional Outline This command is used to save the following data from HDD of PBX to MAT. 2. Parameters Input data Direction Select: PBX Hard Disk to MAT MAT to PBX Hard Disk Verify HDD against MAT Data Type Selection: Data Memory Note 1 Name display Wireless Call Forwarding Program data Note 2 Call Forwarding Speed Calling User Assign Soft Key Number Sharing Note 3 Call Block ACD Data Memory LP Select: This data appears only when Call Forwarding, Speed Calling, User Assign Soft Key, Number Sharing, or Call Block data is designated. Auto Verify Afterward Note 1:When Data Memory is selected, Network Data Memory (NDM) and Local Data Memory (LDM) are also saved/verified simultaneously. Note 2:Program data can be valid when MAT to PBX Hard Disk option in the Direction Select list box is se- lected. Note 3:By saving the Number Sharing data, the data concerning Dual Station Calling Over-FCCS is also saved/verified automatically.
CHAPTER 8 NDA-24238 Page 592 Revision 3.0 MAINTENANCE COMMANDS HDD_MAT_N:Data Control Between HDD and MAT for NDM 1. Functional Outline This command, available at the NCN only, installs (overwrites) the updated Program data from the centralized MAT onto the HDD of all local nodes. To use this command, first install the updated program data on the HDD of the MAT and then execute the program installing onto the HDD of each LN. 2. Parameters Input data Data Type Selection: Select all the listed program data Execution Button: Installing of program data is to be executed
NDA-24238 CHAPTER 8 Page 593 Revision 3.0 MAINTENANCE COMMANDS HDFP:HDD Format of PBX 1. Functional Outline This command is used to execute the formatting of the HDD of PBX. 2. Parameters Input Data (Selection by check) 0 System: HDD of No.0 System 1 System: HDD of No.1 System Buttons Execute: Click to execute the formatting. Close: Click to exit this command.