NEC Neax 2400 Imx System Operations And Maintenance Manual
Have a look at the manual NEC Neax 2400 Imx System Operations And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 616
NDA-24238 CHAPTER 8
Page 589
Revision 3.0
MAINTENANCE COMMANDS
HDD_FDD:Data Control Between HDD and FDD
1. Functional Outline
This command is used to install the program data from FDD of PBX to HDD of PBX, and to verify the program
data between FDD of PBX and HDD of PBX.
2. Parameters
Input data [When system uses software Release 1 or 2]
System Select: HFD0
HFD1
Direction Select: Floppy Disk to Hard Disk
Verify HDD against FDD
Note:Hard Disk to Floppy Disk cannot be selected.
Data Type Selection:...](http://img.usermanuals.tech/thumb/54/84348/w64_nec-neax2400-imx-system-operations-and-maintenance-manual_d-615.png "Page 616
NDA-24238 CHAPTER 8
Page 589
Revision 3.0
MAINTENANCE COMMANDS
HDD_FDD:Data Control Between HDD and FDD
1. Functional Outline
This command is used to install the program data from FDD of PBX to HDD of PBX, and to verify the program
data between FDD of PBX and HDD of PBX.
2. Parameters
Input data [When system uses software Release 1 or 2]
System Select: HFD0
HFD1
Direction Select: Floppy Disk to Hard Disk
Verify HDD against FDD
Note:Hard Disk to Floppy Disk cannot be selected.
Data Type Selection:...")
![Page 621
CHAPTER 8 NDA-24238
Page 594
Revision 3.0
MAINTENANCE COMMANDS
MBCT:Make Busy of Connection Trunk for LDM
1. Functional Outline
This command is used to set/reset the make busy state of the connection trunk.
2. Parameters
Input Data
C_RT: Connection Route Number [1-1023]
C_TK: Trunk Number [1-4095]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy (Outgoing)](http://img.usermanuals.tech/thumb/54/84348/w64_nec-neax2400-imx-system-operations-and-maintenance-manual_d-620.png "Page 621
CHAPTER 8 NDA-24238
Page 594
Revision 3.0
MAINTENANCE COMMANDS
MBCT:Make Busy of Connection Trunk for LDM
1. Functional Outline
This command is used to set/reset the make busy state of the connection trunk.
2. Parameters
Input Data
C_RT: Connection Route Number [1-1023]
C_TK: Trunk Number [1-4095]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy (Outgoing)")
CHAPTER 8 NDA-24238 Page 594 Revision 3.0 MAINTENANCE COMMANDS MBCT:Make Busy of Connection Trunk for LDM 1. Functional Outline This command is used to set/reset the make busy state of the connection trunk. 2. Parameters Input Data C_RT: Connection Route Number [1-1023] C_TK: Trunk Number [1-4095] MB: Make Busy Information [0/1] 0=Make Idle 1=Make Busy (Outgoing)
NDA-24238 CHAPTER 8 Page 595 Revision 3.0 MAINTENANCE COMMANDS MBLE:Make Busy of LENS 1. Functional Outline This command assigns the IDLE/BUSY status of Line Equipment Numbers (LENS). 2. Parameters Input data LENS MB: 0=Make Idle 1=Make Busy
CHAPTER 8 NDA-24238 Page 596 Revision 3.0 MAINTENANCE COMMANDS MBPM:Make Busy of Port Microprocessor 1. Functional Outline This command sets or resets the make-busy state of the circuit card that contains the port microprocessor. This setting and resetting is performed individually for each circuit card. If the location of the circuit card containing the port microprocessor is specified in this command, the operating state of all circuit cards mounted in the associated unit is displayed. 2. Parameters Input data MG Unit Group MB Display data MB: 0=Make Idle 1=Make Busy Note:Idle/Busy status can be displayed and assigned by the MB parameter.
NDA-24238 CHAPTER 8 Page 597 Revision 3.0 MAINTENANCE COMMANDS MBRT:Make Busy of Route 1. Functional Outline This command assigns Idle/Busy status for all the trunks in the route designated. 2. Parameters Input data RT: Route Number of the external route/internal route. Ta b l e 8 - 6 provides the meaning of the internal route numbers. MB: 0=Make Idle 1=Make Busy Table 8-6 Route Number Explanation DATA MEANING DATA MEANING 901 Attendant/Desk Console 902 Originating Register Trunk 903 Incoming Register Trunk 904 MF Receiver 905 Sender Trunk DP/PB 906 PB Receiver for Automated Attendant Service 907 AMP 908 Not used 909 Three-Way Conference Trunk 910-912 Not used 913 Three-Way Conference Trunk for ATTCON 914 Not used 915 Night Attendant Console 916 MFC Register 917 MFC Sender 918 Not used 919-926 Modem 927, 928 Not used 929 Data Signaling Trunk-Option 930 Rate Adapter Conversion Trunk 931-947 Not used
CHAPTER 8 NDA-24238 Page 598 Revision 3.0 MAINTENANCE COMMANDS MBSM:Make Busy of System Message Printout 1. Functional Outline This command allows or inhibits the system message printer to output system messages. 2. Parameters Input data PORT NO.: Port Number of the printer MB: 0=Make Idle 1=Make Busy
NDA-24238 CHAPTER 8 Page 599 Revision 3.0 MAINTENANCE COMMANDS MBST:Make Busy of Station 1. Functional Outline This command assigns the Idle/Busy status of stations. 2. Parameters Input data TN STN: Maximum 5 digits for Business system/Maximum 6 digits for Hotel system. MB: 0=Make Idle 1=Make Busy
CHAPTER 8 NDA-24238 Page 600 Revision 3.0 MAINTENANCE COMMANDS MBST_T:Make Busy of Station – Telephone Number 1. Functional Outline This command is used to assign the IDLE/BUSY status of stations, by using Telephone Numbers. This command is available at NCN (for Fusion network) only. 2. Parameters Input Data UGN: User Group Number TELN: Telephone Number (max. 16 digits) MB: Make Busy/Make Idle Display Data FPC: Fusion Point Code (1-253) Note TN: Tenant Number Note STN: Physical Station Number (max. 5 digits for Business system/max. 6 digits for Hotel system) Note Note: This data is for display only. Buttons Get: Click to get information on the station. Set: Click to execute the BUSY/IDLE performance. Exit: Click to exit this command.
NDA-24238 CHAPTER 8 Page 601 Revision 3.0 MAINTENANCE COMMANDS MBTC:Make Busy of Trunk-Continuous 1. Functional Outline This command is used to assign the IDLE/BUSY status of trunks. By using this command, plural trunks can be placed into IDLE/BUSY state simultaneously per a route designated in “RT” parameter. 2. Parameters Input Data RT: R o u t e N u m b e r TK: Trunk Number Note 1 MB: 0=Make Idle 1=Make Busy (Outgoing) 2=Make Busy (Bothway) Note 2 Note 1: Multiple trunks can be assigned simultaneously per a route designated in “RT” parameter. Note 2:2 = Make Busy (Bothway) is not used.
CHAPTER 8 NDA-24238 Page 602 Revision 3.0 MAINTENANCE COMMANDS MBTK:Make Busy of Trunk 1. Functional Outline This command assigns the Idle/Busy status of trunks. 2. Parameters RT: R o u t e N u m b e r TK: Trunk Number MB: 0=Make Idle 1=Make Busy (Outgoing)
NDA-24238 CHAPTER 8 Page 603 Revision 3.0 MAINTENANCE COMMANDS MEM_HDD:Data Control Between Memory and HDD 1. Functional Outline This command is used to save the following data from MEM of PBX to HDD of PBX, and vice versa. 2. Parameters Input data Direction Select: Memory to Hard Disk Hard Disk to Memory Verify HDD against MEM Data Type Selection: Data Memory Note 1 Name Display Wireless Call Forwarding Call Forwarding Speed Calling User Assign Soft Key Number Sharing Note 2 Call Block ACD Data Memory LP Select: This data is valid when Call Forwarding, Speed Calling, User Assign Soft Key, Number Sharing or Call Block data is designated. Auto Verify Afterward Note 1:When Data Memory is selected, Network Data Memory (NDM) and Local Data Memory (LDM) are also saved/verified simultaneously. Note 2:By saving the Number Sharing data, the data concerning Dual Station Calling Over-FCCS is also saved/verified automatically.