Home > NEC > Communications System > NEC Neax 2400 Imx System Operations And Maintenance Manual

NEC Neax 2400 Imx System Operations And Maintenance Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Imx System Operations And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 647
    Add page 581 to Favourites
    image text
    Enable zoom 
    							CHAPTER 8 NDA-24238
Page 554
Revision 3.0
MAINTENANCE COMMANDS
DLSL:Display of Lockout Station - LENS
1. Functional Outline
This command prints the LENS of stations in lockout state.
2. Parameters
Input data
Type: Type of Printout (1-3)
1=Printout of all LEN in lockout
2=Printout of locked out LEN in the designated Module Group
3=Printout of locked out LEN in the designated Unit
MG:
Note 1, Note 2
UNIT:Note 2
Note 1:
The parameter is valid only when Type=2.
Note 2:The parameter is valid only when Type=3.
Display data
LENS
    Add page 582 to Favourites
    image text
    Enable zoom 
    							NDA-24238 CHAPTER 8
Page 555
Revision 3.0
MAINTENANCE COMMANDS
DLSS:Display of Lockout Station - Number
1. Functional Outline
This command prints the stations in lockout state by station number.
2. Parameters
Input data
Type: Type of Printout (1-3)
1=Printout of all lockout stations
2=Printout of lockout stations by tenant
3=Printout of lockout stations within a specified range of station number.
TN:
Note 1, Note 2
Start STN: Maximum 6 digitsNote 2
End STN: Maximum 6 digitsNote 2
Note 1:
The parameter is valid only when Type=2.
Note 2:The parameter is valid only when Type=3.
Display data
CNT: Count
TN
STN
LENS
    Add page 583 to Favourites
    image text
    Enable zoom 
    							CHAPTER 8 NDA-24238
Page 556
Revision 3.0
MAINTENANCE COMMANDS
DLSS_T:Display of Lock Out Station – Number – Telephone Number
1. Functional Outline
This command is used to print out stations in lockout state, by using Telephone Numbers. This command is
available at NCN (for Fusion network) only. 
2. Parameters
Input Data
TYPE: Printout of all lockout stations
Printout of lockout stations by tenant
Printout of lockout stations within a specified range of station number
UGN: User Group Number 
Note 1, Note 2
Start TELN: First Telephone Number (max. 16 digits) Note 2
End TELN: End Telephone Number (max. 16 digits) Note 2
Note 1:
This parameter is valid when “Type =Printout of lockout stations by tenant” is selected.
Note 2:This parameter is valid when “Type =Printout of lockout stations within a specified range of station
number” is selected.
Display Data
FPC: Fusion Point Code (1-253)
TN: Tenant Number
Start STN: First Physical Station Number 
(max. 5 digits for Business/max. 6 digits for Hotel system)
End STN: End Physical Station Number 
(max. 5 digits for Business/max. 6 digits for Hotel system)
CNT: Count
UGN: User Group Number
TELN: Telephone Number (max. 16 digits)
LENS: Line Equipment Number
Buttons
Get: Click to get information on the lockout status.
Exit: Click to exit this command.
    Add page 584 to Favourites
    image text
    Enable zoom 
    							NDA-24238 CHAPTER 8
Page 557
Revision 3.0
MAINTENANCE COMMANDS
DLTEL:Display of Telephone Number from LENS for LDM
1. Functional Outline
This command, available at each Local Node (LN), is used to display the Telephone Number or other station
data by designating a specific LEN.
2. Parameters
Input Data
LENS: Line Equipment Number [6 digits]
Display Data
UGN: User Group Number
TELN: Telephone Number [Max. 16 digits]
TN: Tenant Number
STN: Station Number [Max. 6 digits]
TEC: Telephone Equipment Class [1-31]
RSC: Route Restriction Class [0-15]
SFC: Service Feature Class [0-15]
    Add page 585 to Favourites
    image text
    Enable zoom 
    							CHAPTER 8 NDA-24238
Page 558
Revision 3.0
MAINTENANCE COMMANDS
DNTEL:Display of Telephone Number from LENS for NDM
1. Functional Outline
This command, available at Network Control Node (NCN) only, is used to display the Telephone Number or
other station data by designating a specific FPC and LEN.
2. Parameters
Input Data
FPC: Fusion Point Code [1-253]
LENS: Line Equipment Number [6 digits]
Display Data
UGN: User Group Number
TELN: Telephone Number [Max. 16 digits]
NID: Network ID 
Note
TN: Tenant Number
STN: Station Number [Max. 6 digits]
TEC: Telephone Equipment Number [1-31]
RSC: Route Restriction Class [0-15]
SFC: Service Feature Class [0-15]
Note:Network ID (NID) is allocated automatically when the Module Group/Unit data is assigned by the
AFMU command. Refer to the “Fusion Network System Manual” for more information.
    Add page 586 to Favourites
    image text
    Enable zoom 
    							NDA-24238 CHAPTER 8
Page 559
Revision 3.0
MAINTENANCE COMMANDS
DPKG:Display of Setting Port Package
1. Functional Outline
This command is used to display the circuit card name accommodated in each Group of a specific UNIT.
Note:When using this command, make sure that each circuit card related database files have already been
installed to your MAT. (See FLINST command for more information.)
2. Parameters
Input Data
MG: Module Group (MG) number [00-07]
UNIT: Unit (U) number [0-3]
Buttons
Get: Click to get information on mounted circuit cards.
Close: Click to exit this command.
Note:When the Input Data above is entered and the “Get” button is pressed, the related circuit card name is
displayed on a Group basis. However, if the name is not found for some reasons, the following mark
may appear in the relevant display field.
#→Unidentifiable firmware type.
##→Data not found in the FMID (database).
###→Group data not assigned.
*→Circuit card name not found (for the card is in make-busy state, etc.).
    Add page 587 to Favourites
    image text
    Enable zoom 
    							CHAPTER 8 NDA-24238
Page 560
Revision 3.0
MAINTENANCE COMMANDS
DPSW:Display Package Switch Status
1. Functional Outline
This command is used to display the following information on a Line/Trunk or Control circuit card:
[When MAT is in On-Line Mode (=connected to the system)]
 Current status of each switch
 Explanation of each switch function
[When MAT is in Off-Line Mode (= not connected to the system)]
 Explanation of each switch function
Note 1:When using this command, make sure that each circuit card related database files have already been
installed to your MAT. (See FLINST command for more information.)
2. Parameters
Input Data
KIND: Display Kind (selection)
 (MAT=) On-Line Mode
 (MAT=) Off-Line Mode
TYPE: Circuit Card Type (selection)
 Line Trunk Package
 Control Package
PMN: Port Micro Processor Number
PKG NAME: Circuit Card Name
LP: Local Partition Number [00-06 
(Even Number only)] 
Note 2
SYSTEM: System Note 2
0=No.0 System
l=No.1 System
MG: Module Group Number [00-07] 
Note 2
UNIT: Unit Number [0-3] Note 2
ACT/STBY: ACT/ST-BY information Note 2
0=ACT
l=ST-BY
2=Not used
No: IOC Card Number [0/1] 
Note 2
Note 2:
This parameter may appear when “Control Package” is selected in the “TYPE” parameter.
Buttons
Get: Click to view the display data
Page Up: Click to view the next page data (when next page exists).
Page Down: Click to return to the previous page data.
Exit: Click to exit this command.
Display Data
PKG Name: Circuit Card Name
Firm Name/Issue: Firm Name/Issue of the circuit card
Each switch data is also displayed on the dedicated display page.
    Add page 588 to Favourites
    image text
    Enable zoom 
    							NDA-24238 CHAPTER 8
Page 561
Revision 3.0
MAINTENANCE COMMANDS
DSTN:Display of Station Data
1. Functional Outline
This command is used to display the registered Station Data corresponding to the designated Tenant and
Station Number. In addition, the information of Hot Line, D
term Key Layout, Hunting, and Call Pickup, etc,
can also be displayed as the data related to the designated stations.
2. Parameters
Input Data
TN: Tenant Number
STN: Station Number [0-9, #, * (Max. 6 digits)]
Buttons
[For display data selection]
SHP: Station Hunting Group-Pilot 
Note
KYD: Key Data for Dterm Note
CPG: Call Pickup Group Note
CPE: Call Pickup Expand Group Note
PHN: Phantom Station Number Note
SHC: Station Hunting-Circular Note
SHU: Station Hunting-UCD Note
HLS: Hot Line Station Note
Note:
When the designated station has any of these data, the corresponding button(s) can be selected. If the
data is necessary, click the button(s).
[For execution order]
Get: Click to view the display data.
Close: Click to exit this command.
Display Data (by Parameters)
ETN: Effective Tenant Number
LENS: Line Equipment Number (6 digits)
TEC: Telephone Equipment Class [1-31]
l=DP (10pps) 2=PB
3=DP/PB 4=DP (20pps)
5-11=Not used 12=D
term
13=Data Terminal via Dterm14=Hot Line
15=CAS Line 16=Data Terminal via Data Module
17=Not used 18=Virtual Line Appearance (for D
term Multi-Line)
19-22=Not used 23=ISDN Terminal
24-26=Not used 27=8 Conference Equipment
28-31=Not used
RSC: Route Restriction Class [0-15]
SFC: Service Feature Class [0-15]
    Add page 589 to Favourites
    image text
    Enable zoom 
    							CHAPTER 8 NDA-24238
Page 562
Revision 3.0
MAINTENANCE COMMANDS
DTELN:Display of Telephone Number Data for NDM
1. Functional Outline
This command is used to display the registered station data corresponding to specified User Group Number
(UGN) and Telephone Number (TELN). The following data related to Number Group can be displayed by
clicking the selection button for each data. This command can be used only when logging in to Network
Control Node (NCN).
 ACPGN: Call Pickup Group (NDM)
 ACPEN: Call Pickup Expand Group (NDM)
 ASHUN: Station Hunting Group-UCD (NDM)
 ASHCN: Station Hunting Group-Circular (NDM)
 AHLSN: Hot Line Station (NDM)
 ASHPN: Station Hunting Group-Pilot (NDM)
 AKYD: Key Data for D
term
2. Parameters
Input Data
UGN: User Group Number
TELN: Telephone Number
Display Data
FPC: Fusion Point Code (1-253)
TN: Tenant Number
STN: Station Number
LENS: Line Equipment Number (6 digits)
MG: Module Group Number
UNIT: Unit Number
G: Group Number
LV: L e v e l  N u m b e r
TEC: Telephone Class (1-31)
RSC: Route Restriction Class (0-15)
SFC: Service Feature Restriction Class (0-15)
    Add page 590 to Favourites
    image text
    Enable zoom 
    							NDA-24238 CHAPTER 8
Page 563
Revision 3.0
MAINTENANCE COMMANDS
Selection Button
CPGN: Call Pickup Group (NDM)
CPEN: Call Pickup Expand Group (NDM)
SHUN: Station Hunting Group-UCD (NDM)
SHCN: Station Hunting Group-Circular (NDM)
HLSN: Hot Line Station (NDM)
SHPN: Station Hunting Group-Pilot (NDM)
KYD: Key Data for D
term
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Imx System Operations And Maintenance Manual