Home > NEC > Communications System > NEC Neax 2000 Ivs2 Installation Procedure Manual

NEC Neax 2000 Ivs2 Installation Procedure Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2000 Ivs2 Installation Procedure Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 416
    Add page 81 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 55

For Fixed Equipment
(1) Fix the BASE PLATE to the floor with anchor bolts. 
(2) Fix the BASE to the BASE PLATE with screws. See Figure 2-12.
(3) Fix the PIM onto the BASE with screws. See Figure 2-13.

For Stationary Equipment
(1) Fix the BASE TRAY to the floor with anchor bolts. 
(2) Fix the PIM onto the BASE with screws. See Figure 2-13.
(3) Place the Module and the BASE on the BASE TRAY. See Figure 2-
14.
Connect PIMs with screws. See Figure 2-17.
Install the I/F BRACKET to the top-stack PIMs if the equipment is 
stacked with five or more PIMs. See “Installation of I/F BRACKET” on 
Page 69
.
Install the TOP COVER to the top-stack PIM. See “Installation of TOP 
COVER” on Page 70
.
Install the MOUNTING BRACKET to the top-stack PIM if the equipment 
is stacked with four or more PIMs. See “Installation of MOUNTING 
BRACKET” on Page 71
.
Carefully review every step above to ensure that all necessary screws 
are properly placed and tightened.
Installation of
Checking
End 
A
Installation of PIM
Multiple-Module
Installation of
To p  C o v e r
Installation of
Mounting Bracket
    Add page 82 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure ManualPage 56ND-70928 (E), Issue 1.0
Figure 2-7  Floor Space
PIM/BATTM
FRONT
BASE
1000 (39.4)223 (8.8)
200 (7.9) 430 (16.9)
200 (7.9)UNIT : mm (inch)
MAINTENANCE 
AREA
    Add page 83 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 57
Figure 2-8  Cable Hole Location
BASE PIM
 : CABLE HOLE FRONT
    Add page 84 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure ManualPage 58ND-70928 (E), Issue 1.0
Figure 2-9  Floor Marking for BASE PLATE (for Fixed Equipment)
Figure 2-10  Floor Marking for BASE TRAY (for Stationary Equipment)
(WALL)UNIT : mm (inch)
202.6 
(7.9)ANCHOR BOLT x 4
347.2 (13.7)
412.4 (16.2) 30 
(1.2)30 
(1.2)
34 
(1.3)128 
(5.0)40.6 
(1.6)
 
Using MOUNTING BRACKET: 10 (0.4) 
Not Using MOUNTING BRACKET
: 1.7 (0.1)
ANCHOR BOLT x 4
45 128
(1.8) (5.0)
43.9
(1.7)347.2
(13.7) UNIT : mm (inch)
    Add page 85 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 59
Drilling
(1) Make a preliminary hole in the concrete, using a drill bit for small-diameter holes.
(2) Drill a hole in the concrete with a drill suitable for a plug bolt a little deeper than the plug 
bolt length.
Anchor Bolt Size : 10mm (0.39 inch) DIA for Fixed Equipment
6mm (0.24 inch) DIA for Stationary Equipment
(3) Insert the anchor bolt into the hole.
(4) Push anchor bolt until the bolt stays permanently in place.
(5) Turn bolt counterclockwise and remove.
(6) Insert bolts correctly into the holes for equipment installation, then tighten them properly.
Figure 2-11  Drilling Instructions for Anchor Bolt
(3) (4) (5) (6) (1) (2)
    Add page 86 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure ManualPage 60ND-70928 (E), Issue 1.0
Detaching FRONT COVER
(1) Push portion A of the COVER PARTS to release the LATCH.
(2) Pivot the COVER PARTS on its left side to remove it.
(3) Loosen its one screw.
(4) Lift up the STOPPER to unlock.
(5) Pivot the FRONT COVER on its bottom to remove it.
Detaching FRONT COVER
(1) PUSH COVER PARTS.
(2) REMOVE COVER PARTS.
COVER PARTSPUSH
PORTION A
    Add page 87 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 61
(3) LOOSEN A SCREW.
(4) LIFT UP STOPPER (UNLOCK).
    Add page 88 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure ManualPage 62ND-70928 (E), Issue 1.0
(5) REMOVE FRONT COVER.
    Add page 89 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 63
Connection of BASE and BASE PLATE for Fixed Equipment
(1) Mount the BASE on the BASE PLATE by placing it over the hooks.
(2) Slide the BASE into the inner end.
(3) Secure the BASE to the BASE PLATE with two screws.
NOTE:
Screws are attached to the BASE PLATE.
Figure 2-12  Connection of BASE and BASE PLATE
FRONT
BASE PLATEBASE
HOOKS
BASE
BASE PLATESLIDE BASE INTO INNER END.
    Add page 90 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 INSTALLATION
Floor Standing Installation
NEAX2000 IVS2 Installation Procedure ManualPage 64ND-70928 (E), Issue 1.0
Connection of PIM and BASE for Fixed/Stationary Equipment
(1) Mount the PIM on the BASE by placing it over the hooks.
(2) Slide the PIM into the inner end.
(3) Fix the PIM to the BASE with three screws.
NOTE:
Screws are attached to the Module.
Figure 2-13  Connection of PIM and BASE
SCREWS
BASE PIMBASE
HOOKS
    
  SLIDE PIM INTO 
      INNER END.
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2000 Ivs2 Installation Procedure Manual