NEC Neax 2000 Ivs2 Installation Procedure Manual

							CHAPTER 1 GENERAL INFORMATION
Control Card
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 15
Control Card
This table shows the names and functions of each control card.
Table 1-3  Control Card Name and Function
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION
PN-CP14 MP Main Processor Card
Provides Memory, TDSW (1024CH x 1024CH), 16-line CFT, 
PB sender, Clock, PLO 2 ports (receiver mode/source 
mode), two RS-232C ports, 2-line DAT (Recording duration: 
Max. 128sec.), DK, 4-line PB receiver, Modem for remote 
maintenance (19.2 kbps), internal Music-on-Hold tone 
source and BUS interface. BUS interface functions as a 
driver/receiver of various signals, adjusts gate delay timing 
and cable delay timing, monitors I/O Bus and PCM BUS.
One card is required per system.
PN-CP15 FP Firmware Processor Card
Provides Line/Trunk interface, Memory (RAM 768KB), and
inter-module BUS interface. BUS interface functions as a
driver/receiver of various signals, adjusts gate delay timing
and cable delay timing, monitors I/O Bus and PCM BUS.
When the system consists of three PIMs or more, one each
of this card is mounted respectively in PIM0, PIM2, PIM4,
and PIM6.
PN-PW00 EXTPWR Power Supply Card for DESKCON
Provides –48V DC power.
Max. four cards per frame (four PIMs). Max. three cards per
PIM. Occupies two physical slots width per card.
PZ-PW121 AC/DC PWR Main Power Supply Card
Input: AC120V/240V (50Hz/60Hz)
Output:–27V (4.4A), +5V (7.2A), CR (38mA), +90V (80mA)
One card is pre-installed per PIM.
PZ-PW122 DC/DC PWR Power Supply Card for Cell Station (Zone Transceiver)
Input:–24V DC
Output:–48V DC (1.7A)
One card per PIM.
Max. 16 CS (ZT)s backed up by one card. 
						

							CHAPTER 1 GENERAL INFORMATION
Application Processor Card
NEAX2000 IVS2 Installation Procedure ManualPage 16ND-70928 (E), Issue 1.0
Application Processor Card
This table shows the names and functions of each application processor card.
Table 1-4  Application Processor Card Name and Function 
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION
PN-AP00-A
[For North 
America/
Latin America 
Only]DBM Data Base Module Card for WCS Roaming function
One card per WCS system.
PN-AP00-B AP00 Application Processor Card
Provides four RS-232C ports and is used for SMDR, Hotel
Printer, CIS, PMS, MCI, CS report functions.
One card per system.
PN-AP01 AP01 Application Processor Card
Provides one RS-232C port and one Ethernet interface port.
Used for OAI function, ID code expansion.
One card per system.
PN-BRTA BRT 1-line Basic Rate (2B+D) Interface Trunk Card
Accomodates one 2-channel PCM digital lines.
PN-2BRTC BRT 2-line Basic Rate (2B+D) Interface Trunk Card
Accomodates two 2-channel PCM digital lines.
PN-CC01 ETHER Ethernet Control Card
Used with the PN-AP01 card to accommodate the Ethernet
and transmit/receive a signal of TCP/IP protocol.
10 BASE-T twisted pair cable is connected directly to this
card. 
						

							CHAPTER 1 GENERAL INFORMATION
Application Processor Card
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 17
PN-DAIA DAI Digital Trunk Interface (23B+D, 1.5 Mbps) Card for Remote
PIM
Accomodates 24-channel PCM digital lines, and provides
Firmware Processor and BUS interface.
One through three cards, corresponding to the number of
remote site, must be provided at main site.
PN-DAIB DAI Digital Trunk Interface (23B+D, 1.5 Mbps) Card for Remote
PIM
Accomodates 24-channel PCM digital lines, and provides
Firmware Processor.
One card is required per Remote PIM at remote site.
PN-DAIC DAI Digital Trunk Interface (23B+D, 1.5 Mbps) Channel
Expansion Card 
Accomodates 24-channel PCM digital lines.
One through six cards can be provided at main site.
Two cards can be provided at remote site.
PN-DAID DAI Digital Trunk Interface (2 Mbps) Card for Remote PIM 
Accomodates 30-channel PCM digital lines, and provides
Firmware Processor and BUS interface.
One through three cards, corresponding to the number of
remote site, must be provided at main site.
PN-DAIE DAI Digital Trunk Interface (2 Mbps) Card for Remote PIM 
Accomodates 30-channel PCM digital lines, and provides
Firmware Processor.
One card is required per Remote PIM at remote site.
PN-DAIF DAI Digital Trunk Interface (2 Mbps) Channel Expansion Card 
Accomodates 30-channel PCM digital lines.
One through three cards can be provided at main site.
One card can be provided at remote site.
PN-24DTA-C DTI Digital Trunk Interface (23B+D, 1.5 Mbps) Card
Accommodates 24-channel PCM digital lines.
PN-30DTC-A DTI Digital Trunk Interface (2 Mbps) Card
Accommodates 30-channel PCM digital lines.
Table 1-4  Application Processor Card Name and Function (Continued)
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION 
						

							CHAPTER 1 GENERAL INFORMATION
Application Processor Card
NEAX2000 IVS2 Installation Procedure ManualPage 18ND-70928 (E), Issue 1.0
PN-IPTA IPT IP Trunk Card
Accommodates the IP network and transmit/receive com-
pressed voice or signals over IP network.
Used with max. four PN-4VCTH cards (16 channels).
10 BASE-T/100 BASE-TX twisted pair cable is connected
directly to this card.
PN-24PRTA PRT ISDN Primary Rate (23B+D) Interface Card
Provides a built-in D-channel Handler (DCH).
PN-4RSTB MFR 4-line MF Receiver, MFC Receiver/Sender Card
Used for MF/MFC-R2 Signaling on DID/DOD trunks.
Max. four cards can be provided per system, including the
PN-4RSTC card.
PN-4RSTC CIR 4-line Caller ID Receiver Trunk Card
Used for Caller ID (CLASS SM) on analog trunks.
Max. four cards per system, including the PN-4RSTB card.
PN-SC00 CCH Common Channel Handler Card
Transmits/receives signals on the common signalling channel
of No. 7 CCIS.
PN-SC01 DCH D-channel Handler Card
Transmits/receives signals on the D-channel of ISDN Primary
Rate (23B+D) interface or WCS Roaming interface.
PN-SC03 ICH ISDN-channel Handler Card
Provides the D-channel signaling interface and controls max.
four ILC cards (Layer 2 and 3).
PN-SC03-A CSH CS(ZT) Handler Card
Provides the D-channel signaling interface and controls
max. four CSI cards, eight CS(ZT)s.
Table 1-4  Application Processor Card Name and Function (Continued)
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION 
						

							CHAPTER 1 GENERAL INFORMATION
Application Processor Card
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 19
PZ-M537 EXPMEM Memory Expansion Card for MP/AP00 Card
The system capacity is expanded as follows:
When mounted on PN-CP14 (MP) card:
 
When mounted on PN-AP00-B (AP00) card:
 
PZ-M542
[For Other 
Countries]CONN Coaxial Cable Connection Card
Used to connect a coaxial cable for Digital Trunk Interface.
Max. two cards can be connected to LTC connector of each
PIM.
PZ-M557
[For 
Australia]CONN Coaxial Cable Connection Card
Used to connect a coaxial cable for Digital Trunk Interface.
Max. two cards can be connected to LTC connector of each
PIM.
Table 1-4  Application Processor Card Name and Function (Continued)
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION
System Capacity w/o EXPMEM with EXPMEM
Line/Trunk 384 768
DID dial conversion 500 1000
IP trunk 1 4
Analog Station 256 512
D
term256 512
Analog Station+D
term256 512
Analog Station+D
term+PS256 512
D
term (24/32 button)256 512
PS 128 256
ISDN terminal 64 128
Data station 64 128
Call Forwarding-Outside set 240 496
Authorization Code/
Forced Account Code/
Remote Access to System 
(DISA) Code1000 3000
Message Remider set 512 1024
Name Display/
Guest Name Display256 512
Speed Calling-Station
(Station Speed Dial) set4000 10000
MP built-in SMDR call record 256 1280
System Capacity w/o EXPMEM with EXPMEM
SMDR call record 1600 27000 
						

							CHAPTER 1 GENERAL INFORMATION
Line/Trunk Card
NEAX2000 IVS2 Installation Procedure ManualPage 20ND-70928 (E), Issue 1.0
Line/Trunk Card
This table shows the names and functions of each line/trunk card.
Table 1-5  Line/Trunk Card Name and Function 
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION
PN-2AMPA AMP 2-line Amplifier Trunk Card
Provides Echo Canceller (EC), Automatic Gain Controller
(AGC) and Tone Disabler (TD) functions.
PN-AUCA AUC 2-line Analog Long Line Circuit Card provided with Power
Failure Transfer (PFT) Function, or 2-line Direct Inward
Dialing Trunk Card
Line resistance in the case of a long line circuit:
Max. 2500 ohms (inclusive of the internal resistance of the
distant office equipment)
Equipped with –48V DC-DC on-board power supply.
PN-CFTA CFT 6/10 Party Conference Trunk Card
Use of one card: Can control a conference of up to six
participants.
Use of two cards: Can control a conference of up to ten
participants.
PN-CFTB CFT 6 Party Conference Trunk Card
One card can control a conference of up to ten par ticipants.
Occupies 8 time slots per one card.
PN-2COTD
[For Austra-
lia/Others]COT 2-line Central Office Trunk Card (Loop Start Trunk)
Provides metering pulse detection function.
PN-4COTA-A COT 4-line Central Office Trunk Card (Loop Start Trunk)
PN-4COTB COT 4-line Central Office Trunk Card (Ground Start Trunk)
Provides loop detection, sending/detecting ground on Tip/
Ring wire.
PN-4COTF
[For N.Z.]COT 4-line Central Office Trunk Card (Loop Start/Ground Start
Tr u n k )
Provides loop holding, pulse sender, and a detector for
ground signals. 
						

							CHAPTER 1 GENERAL INFORMATION
Line/Trunk Card
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 21
PN-4COTE
[For 
Australia]COT 4-line Central Office Trunk Card (Loop Start Trunk)
Provides a detector for line fault conditions.
PN-4COTG COT 4-line Central Office Trunk Card (Loop Start trunk)
Provides loop detection, receiving/sending the Caller ID
(CLASS SM) signal.
PN-6COTJ
[For 
Australia]COT 6-line Central Office Trunk Card (Loop Start Trunk)
Provides a detector for line fault conditions.
PN-8COTR COT 8-line Central Office Trunk Card (Loop Start Trunk)
PN-8COTS COT 8-line Central Office Trunk Card (Ground Start Trunk)
Provides loop detection, sending/detecting ground on Tip/
Ring wire.
PN-8COTT
[For 
Australia]COT 8-line Central Office Trunk Card (Loop Start Trunk)
Provides a detector for line fault conditions.
PN-8COTQ COT 8-line Central Office Trunk Card (Loop Start Trunk)
Provides loop detection, receiving/sending the Caller ID
(CLASS SM) signal.
PN-2CSIA
[For North 
America/
Latin 
America]CSI 2-line Zone Transceiver Interface Card
Used to interface with the ZT, based on ISDN S-interface.
Max. two ZTs can be connected per CSI card.
Occupies eight time slots per one card.
PN-2CSIA-A
[For Austra-
lia/Others]CSI 2-line Cell Station Interface Card
Used to interface with the CS, based on ISDN S-interface.
Max. two CSs can be connected per one card.
Occupies eight time slots per one card.
PN-4DATC DAT 4-line Digital Announcement Trunk Card
Recording duration: Max. 120 seconds
Occupies eight time slots per one card.
Table 1-5  Line/Trunk Card Name and Function (Continued)
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION 
						

							CHAPTER 1 GENERAL INFORMATION
Line/Trunk Card
NEAX2000 IVS2 Installation Procedure ManualPage 22ND-70928 (E), Issue 1.0
PN-2DITA
[For Hong 
Kong]DIT 2-line Direct Inward Dialing Trunk Card
Provides loop detection, sending reverse signal and PB to
DP signal conversion.
Equipped with –48V DC-DC on-board power supply.
PN-4DITB DIT 4-line Direct Inward Dialing Trunk Card
Provides loop detection, sending reverse signal and PB to
DP signal conversion.
Equipped with –48V DC-DC on-board power supply.
PN-DK00 DK 8-circuit External Relay Control/External Key Scan Card
Provides the above-mentioned control functions on a per cir-
cuit basis.
PN-2DLCB/
PN-2DLCNDLC 2-line Digital Long Line Circuit Card for D
term75/65 (Series E/
III), D
term70/60 (Elite/Electra Pro), DSS Console, ATTCON
[–48V version, 2-wire type]
Equipped with –48V DC-DC on-board power supply.
PN-2DLCC DLC 2-line Digital Long Line Circuit Card for SN610 ATTCON
[–48V version, 4-wire type]
Equipped with –48V DC-DC on-board power supply.
PN-4DLCF DLC 4-line Digital Line Circuit Card for SN610 ATTCON
[–27V version, 4-wire type]
PN-4DLCM DLC 4-line Digital Line Circuit Card for D
term75/65 (Series E/III),
D
term70/60 (Elite/Electra Pro), DSS Console, ATTCON,
DESKCON
 [–27V version, 2-wire type]
PN-4DLCQ DLC 4-line Digital Line Circuit Card for D
term75/65(Series E/III),
DSS Console, ATTCON, DESKCON
[–27V version, 2-wire type]
PN-8DLCL DLC 8-line Digital Line Circuit Card for D
term75/65 (Series E/III),
D
term70/60 (Elite/Electra Pro), DSS Console, ATTCON,
DESKCON
[–27V version, 2-wire type]
Table 1-5  Line/Trunk Card Name and Function (Continued)
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION 
						

							CHAPTER 1 GENERAL INFORMATION
Line/Trunk Card
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 23
PN-8DLCP DLC 8-line Digital Line Circuit Card for Dterm75/65 (Series E/III),
DSS Console, ATTCON, DESKCON
[–27V version, 2-wire type]
PN-2DPCB DPC 2-line Data Port Controller Card
Used for intra-office or inter-office digital data transmission
on nailed down connection.
Accommodates max. two DTEs with V.11 (X.21) interface or
V.24/V.28 (RS-232C) interface.
PN-2ILCA ILC 2-line ISDN Line Circuit Card
Provides a physical interface to ISDN Terminals.
Occupies eight time slots per one card.
PN-4LCC
[For Others]LC 4-line Analog Line Circuit Card for Single Line Telephones
Loop resistance: Max. 600 ohms (including telephone set)
PN-4LCD-A LC 4-Line Analog Line Circuit Card for Single Line Telephones
Loop resistance : Max. 600 ohms (including telephone set)
Provides momentary open and Message Waiting Lamp
control functions for each circuit.
Equipped with +80V DC-DC on-board power supply.
PN-4LCE
[For 
Australia]LC 4-line Analog Line Circuit Card for Single Line Telephones
Loop resistance: Max. 600 ohms (including telephone set)
PN-4LCF
[For 
Australia]LC 4-line Analog Line Circuit Card for Single Line Telephones
Loop resistance: Max. 600 ohms (including telephone set)
Provides Message Waiting Lamp control function for each
circuit, and reverse function for only No. 3 circuit.
Equipped with +80V DC-DC on-board power supply.
PN-4LCK
[For China]LC 4-Line Analog Line Circuit Card for Single Line Telephones
Loop resistance : Max. 600 ohms (including telephone set)
Table 1-5  Line/Trunk Card Name and Function (Continued)
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION 
						

							CHAPTER 1 GENERAL INFORMATION
Line/Trunk Card
NEAX2000 IVS2 Installation Procedure ManualPage 24ND-70928 (E), Issue 1.0
PN-4LCL
[For China]LC 4-line Analog Line Circuit Card for Single Line Telephones
Loop resistance : Max. 600 ohms (including telephone set)
Provides Message Waiting Lamp control function for each
circuit, and reverse function for only No. 3 circuit.
Equipped with +80V DC-DC on-board power supply.
PN-4LCV
[For Brazil]LC 4-Line Analog Line Circuit Card for Single Line Telephones
Loop resistance : Max. 600 ohms (including telephone set)
PN-4LCW
[For Brazil]LC 4-line Analog Line Circuit Card for Single Line Telephones
Loop resistance : Max. 600 ohms (including telephone set)
Provides Message Waiting Lamp control function for each
circuit, and reverse function for only No. 3 circuit.
Equipped with +80V DC-DC on-board power supply.
PN-8LCAA LC 8-line Analog Line Circuit Card for Single Line Telephones
Loop resistance : Max. 600 ohms (including telephone set)
Provides Message Waiting Lamp control, momentary open
functions for each circuit.
PN-2LDTA
[For 
Australia/Oth-
ers]LDT 2-line Loop Dial Trunk Card
Line resistance: Max. 2500 ohms (including internal resis-
tance of the distant office equipment)
Equipped with –48V DC-DC on-board power supply.
PN-M03 M03 V.35 Data Terminal Equipment Interface Card
Used together with the PN-2DPCB card to provide the V.35
interface.
PN-M10 M10 Optical Interface Card
Provides internal optical modem to T1/E1 network or Remote 
PIM.
Line length : 10 km or less
Line coding : CMI
Table 1-5  Line/Trunk Card Name and Function (Continued)
EQUIPMENT 
NAMEFUNCTIONAL
NAMEFUNCTION