NEC Neax 2000 Ivs2 Installation Procedure Manual

							CHAPTER 2 INSTALLATION
Connection of DC Power Cable
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 85
Connection of DC Power Cable
(1) Confirm the connection of power output cables, as shown below (These cables are pre-
installed).
(2) For PIM0, connect the PWR CNT CA-E to the CN103 connector on the PZ-PW121 card and 
the PWR1 connector on the BWB.
For PIM1 to PIM7, connect the PWR CNT CA-D to the CN103 connector on the PZ-PW121 
card and the PWR1 connector on the BWB.
Figure 2-29  PWR CNT CA-D/PWR CNT CA-E
Figure 2-30  Cable Connection between PZ-PW121 and BWB
550 mm (21.7 inch)300 mm (11.8 inch) 250 mm (9.8 inch)
PWR CNT CA-E  (FOR PIM0) 
PWR CNT CA-D (FOR PIM1 TO PIM7)PWR0B PWR1 PZ-PW121 BWB (BACK WIRING BOARD)PIM
PWR0CPWR0A
POWER OUTPUT CABLE (+90V, CR, E)POWER OUTPUT CABLE (+5V, -27V, E)CARD SLOT AREA
LTC CONNECTOR AREA
CN103 
						

							CHAPTER 2 INSTALLATION
Connection of DC Power Cable
NEAX2000 IVS2 Installation Procedure ManualPage 86ND-70928 (E), Issue 1.0
(3) When you need a –48V DC power supply installed for a Cell Station (Zone Transceiver) in 
WCS system, do the following procedure. If not, skip this procedure and go to item (4) on 
Page 88
.
STEP 1: Attach four screws preliminary to the PZ-PW122 card.
STEP 2: Mount the PZ-PW122 card into the PIM which accommodates the CSI cards, and fas-
ten the screws.
NOTE:
Screws are attached to the PZ-PW122 card.
Figure 2-31  Mounting PZ-PW122 into PIM
PIM
PZ-PW122 
						

							CHAPTER 2 INSTALLATION
Connection of DC Power Cable
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 87
STEP 3:  Connect the PWR CNT CA-E or PWR CNT CA-D, and POWER OUTPUT CABLE 
(–48V, E) as shown below.
Figure 2-32  Cable Connection between PZ-PW121/PZ-PW122 and BWB
PWR CNT CA-E  (FOR PIM0) 
PWR CNT CA-D (FOR PIM1 TO PIM7)PWR0B PWR1 PZ-PW121 BWB (BACK WIRING BOARD)PIM
PWR0CPWR0A
POWER OUTPUT CABLE (+90V, CR, E) PZ-PW122
POWER OUTPUT CABLE (+5V, -27V, E)
POWER OUTPUT CABLE (-48V, E)CARD SLOT AREA
LTC CONNECTOR AREA
CN103 
						

							CHAPTER 2 INSTALLATION
Connection of DC Power Cable
NEAX2000 IVS2 Installation Procedure ManualPage 88ND-70928 (E), Issue 1.0
(4) When the system is configured with two or more PIMs, connect the PZ-PW121 cards to 
each other using the PWR CA-A for power multi-connection.
Figure 2-33  PWR CA-A
Figure 2-34  Connection of PWR CA-A Cables
(a) When using an Internal Battery
550 mm (21. 7inch)
PWR CA-A
PIM3
TO INTERNAL 
BATTERY PWR
PWR 
CA-A
PIM2
PIM1PIM7
PIM6
PIM5
PIM4 PIM0
TO INTERNAL 
BATTERY PWR
TO INTERNAL 
BATTERY PWR
PWR 
CA-A
TO INTERNAL 
BATTERY PWR
TO INTERNAL 
BATTERY PWR
PWR 
CA-A
TO INTERNAL 
BATTERY PWR
TO INTERNAL 
BATTERY PWR
PWR 
CA-A
TO INTERNAL 
BATTERY PWR 
						

							CHAPTER 2 INSTALLATION
Connection of DC Power Cable
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 89
Figure 2-35  Connection of PWR CA-A Cables
(b) When using an External Battery
PIM 3PWR
PIM 2
PIM 1PIM 7
PIM 6
PIM 5
PIM 4 PIM 0
PWR
PWRPWR 
CA-A
PWR
PWR
PWR
PWR
PWR
PWR 
CA-A
TO EXTERNAL BATTERY 
						

							CHAPTER 2 INSTALLATION
Supply Voltage Check And Heat Run Test
NEAX2000 IVS2 Installation Procedure ManualPage 90ND-70928 (E), Issue 1.0
SUPPLY VOLTAGE CHECK AND HEAT RUN TEST
Precautions
(1) Check the switch position of each PZ-PW121 card before turning power on.
Make sure that the AC120V/240V selector switch is positioned to appropriate voltage for 
each country (AC120V or AC240V).
Make sure that the battery mode selector switch is positioned as shown below to meet the 
kind of battery:
(2) When the operating power is being supplied to the PZ-PW121 card, do not plug/unplug this 
circuit card into/from its mounting slot.
(3) Immediately follow the instructions below if the MJ lamp on the PZ-PW121 lights up or 
smoke or an unpleasant odor is produced during the test: 
a) Turn power off of all PZ-PW121 cards.
b) Unplug the AC code from the wall outlet.
c) Carefully check for cause(s) of the failure occurring. 
NOTE:
Do not turn power on again until the cause is detected. 
(4) When the system is configured with two or more PIMs, the BUS cable is providing gang 
control for the PZ-PW121 card of PIM0 and other PIMs. Therefore, if the power of PIM0 is 
off, no power is supplied to the whole system even when the power switch(es) of other PIMs 
are left on. Note, however, that the battery charging is continuing even under these 
circumstances.
SW
240V 100V/120V
ON OFF
12
SW101
1 : Not used 
2 : ON   (SEAL/FLOAT2) 
     OFF (OPEN/FLOAT1) 
  
						

							CHAPTER 2 INSTALLATION
Power Routing
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 91
Power Routing
NOTE 1:PN-4LCD/4LCF/4LCL/4LCW card provides +80V on-board power supply (+80VOBP).
NOTE 2:PN-AUCA, PN-2DLCB/PN-2DLCN, PN-2DLCC, PN-2LDTA, PN-2ODTA/2ODTB card
provides –48V on-board power supply (–48VOBP).
+5V
-27V
Ð27V
CR
+90V
+90V AC
AC PZ-PW121
+5V
-5V
-5V +5V
+80V
-27V-27V
-27V
CR
CR
PZ-PW121
NOTE 1
+80VOBP
+5V
-48V
-27V
CR-48VOBP
NOTE 2
BATTERY PWR CA-A
AC CORD-B
TERMINAL 
BLOCKSBASE PIM0 PIM1 TO  P I M 2
+5V
-27V
-5V
CR
PN-8LCAA
+90V
TO AC MAINS INPUTAC CORD-D 
						

							CHAPTER 2 INSTALLATION
Checking for Supply Voltage
NEAX2000 IVS2 Installation Procedure ManualPage 92ND-70928 (E), Issue 1.0
Checking for Supply Voltage
Heat Run Test
Turn the SW1 switch ON. Keep it on for 5 minutes to check for no abnormal voltage. After com-
pleting the test, turn OFF the SW1 switch of the PZ-PW121 card on PIM0. Then, turn OFF the
SW1 switches of all the PZ-PW121 cards.
Before connecting AC Cord, verify:
- that the SW1 switch of the PZ-PW121 card is positioned to OFF;
- that the AC Cord is unplugged from the wall outlet.
Use a tester to verify that the input power is AC120±10V or AC240±10V.
Plug the AC cord into a wall outlet.
Turn the SW1 switches of all the PZ-PW121 cards on PIM1 to PIM7 to 
ON. Then, turn the SW1 switch of the PZ-PW121 card on PIM0 to ON 
last of all.
Verify that the ON lamp on the PZ-PW121 card lights up.
Measure the output voltage: -20V should be observed at GND and -27V 
terminals of the PZ-PW121 card. See Figure 2-36.
Start 
Checking power cable
Connecting AC power
Turning power ON
Verifying power
Testing for
Testing for input power
End and
grounding conductor
pilot lamp ON
output voltage 
						

							CHAPTER 2 INSTALLATION
Heat Run Test
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 93
Figure 2-36  Confirming Output Voltage
TESTER
DC100V
MJ
MN
ON
-27V
FG
GND
I O
SW1
TO         FRAME GROUND 
TERMINAL IN PIM
TO TERMINAL 
BLOCK ON BASE 
						

							CHAPTER 2 INSTALLATION
Battery Connection
NEAX2000 IVS2 Installation Procedure ManualPage 94ND-70928 (E), Issue 1.0
BATTERY CONNECTION
WAR NIN G
TURN OFF AC POWER BEFORE CONNECTING BATTERIES.
CAU TIO N
1. 24V batteries must be used in this system. 
2. If battery terminals (+,  –) come in contact with the module while connecting the battery cable
to the PZ-PW121 card, the PZ-PW121 card or the BWB may be broken. Therefore, you must
perform work in accordance with the following steps when mounting or removing the batter-
ies.
(1) When mounting batteries: (a) Connect the battery cable to the batteries.
(b) Mount the batteries into the appointed position of the PIM or the BATTM. 
(c) Connect the battery cable to the PZ-PW121 card.
(2) When removing batteries: (a) Disconnect the battery cable from the PZ-PW121 card. 
(b) Remove the batteries from the PIM or the BATTM.
Recommended Battery Internal Battery: YUASA MATSUSHITAtype NPH-3.2-12 
type LCR-12V3.4NE
External Battery: 
(BATTM) YUASA
MATSUSHITAtype NP-24-12B
type LCL-12V-24