NEC Neax 2000 Ivs2 Installation Procedure Manual

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 265
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 1
0-FFP (Firmware Processor) Number setting for the
DAID card.
By this setting, the system regards the DAID card
and the opposite DAIE card as one Firmware Pro-
cessor.
0 Not used
1FP No. 1
2FP No. 2
3FP No. 3
4-F Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW1
(Piano Key SW)1
NOTE 3ONFor supplying 2.0 MHz clock to 
PLO 0
No clock supply to PLO 0
2
NOTE 3ONFor supplying 2.0 MHz clock to 
PLO 1
No clock supply to PLO 1
3 Always set to OFF
4 Always set to OFF
(Continued)
1
32
ON
DOWN
4 
3 
2 
1 OFF
ON
OFF
OFF
OFF
OFF 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 266ND-70928 (E), Issue 1.0
SW2 (DIP SW)
1ONControl channel signaling data 
transmission speed: 48kbps
Control channel signaling data 
transmission speed: 64kbps
2ONCRC Synchronization Detection 
Timer is provided.
CRC Synchronization Detection 
Timer is not provided.
3ON CRC4 Check is provided.
CRC4 Check is not provided.
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
45
67
8ON
OFF
OFF
OFF 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 267
SW2 (DIP SW)
4Setting of control signal time slot
NOTE 4, NOTE 5 OFF
5
OFF
6
OFF
7
OFF
8ON
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
45
67
8ON
ON
SWITCH NUMBER
TIME SLOT
NUMBER
45678
OFFONONONON TS 4
ON OFF ON ON ON TS 5
OFF OFF ON ON ON TS 6
ON ON OFF ON ON TS 7
OFF ON OFF ON ON TS 8
ON OFF OFF ON ON TS 9
OFF OFF OFF ON ON TS 10
ON ON ON OFF ON TS 11
OFF ON ON OFF ON TS 12
ON OFF ON OFF ON TS 13
OFF OFF ON OFF ON TS 14
ON ON OFF OFF ON TS 15
OFFONOFFOFFON TS 16
ON OFF OFF OFF ON TS 17
OFF OFF OFF OFF ON TS 18
ON ON ON ON OFF TS 19
OFFONONONOFF TS 20
ON OFF ON ON OFF TS 21
OFF OFF ON ON OFF TS 22
ON ON OFF ON OFF TS 23
OFF ON OFF ON OFF TS 24
ON OFF OFF ON OFF TS 25
OFF OFF OFF ON OFF TS 26
ON ON ON OFF OFF TS 27
OFF ON ON OFF OFF TS 28
ON OFF ON OFF OFF TS 29
OFF OFF ON OFF OFF TS 30
OFF ON OFF OFF OFF TS 29
ON OFF OFF OFF OFF TS 30
OFF OFF OFF OFF OFF TS 31
ON
ON
ON
OFF 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 268ND-70928 (E), Issue 1.0
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card.  SW3 (DIP SW) 1 Always set to ON
2 Always set to ON
3 Always set to ON
4 Always set to OFF
JPS (Jumper pin) Balanced transmission: 120 ohms 
(For twisted-pair cable)
LeftTA is grounded on the transmission 
line: 75 ohms (For coaxial cable)
JPR (Jumper pin) Balanced transmission: 120 ohms 
(For twisted-pair cable)
LeftRA is grounded on the transmission 
line: 75 ohms (For coaxial cable)
E1Z (Jumper pin) Line impedance: 
120 ohms (For twisted-pair cable)
LeftLine impedance: 
75 ohms (For coaxial cable)
SRT (Jumper pin)
Right
For mounting this card on PIM0
LeftFor mounting this card on PIM1-
PIM7
JP (Jumper pin) Line impedance: 
120 ohms (For twisted-pair cable)
DOWNLine impedance: 
75 ohms (For coaxial cable)
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
4ON
ON
ON
ON
ON
Right
Right
Right
UP 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 269
NOTE 3:
When clock source office signal is supplied via the line between the main site and the
remote site, set the SW1-1 and SW1-2 as the following table. In this case, DAID cards
(DAID0, DAID1) must be mounted in PIM0.
NOTE 4:
The time slot number 0 and 28 (TS0/28) cannot be used for control signal.
NOTE 5:
This setting must be identical with the opposite DAIE card.
CONDITIONSDAI D0 DAID 1 DAID2
REMARKS
SW
1-1SW
1-2SW
1-1SW
1-2SW
1-1SW
1-2
One DAID card 
is provided.ON OFF––––The clock signal is sent 
to PLO0 of MP card via 
supply route 0 (DAID0).
Two or three 
DAID cards are 
provided.ON OFF OFF ON OFF OFFThe clock signal supply 
route is automatically 
changed to the route 1 
(DAID1), if a transmis-
sion line failure occurs 
on the supply route 0. 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIE (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 270ND-70928 (E), Issue 1.0
PN-DAIE (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Remains lit when a link between this card and a distant office is
normally connected.
Goes out after 15 seconds of link disconnection.
RMT Red Remains lit when receiving the alarm signal from a distant office.
LOOP–Not used
BL Red Remains lit while data transmission on control channel (D ch).
Remains lit while FP data downloading.
JPS JPR E1Z
SW2
SW3BUS
CNSENSE
RUN
MB
SW1LINK 
RMT 
LOOP 
BL
JP 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIE (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 271
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE 
(Rotary SW)
0-FAlways set to 0
1-F
Not used
MB (Toggle SW)
NOTE 1UP
For make-busy
For normal operation
SW1 
(Piano Key SW)1
Always set to OFF
2
Always set to OFF
3
Always set to OFF
4
Always set to OFF
SW2 (DIP SW)
1ONControl channel signaling data 
transmission speed: 48kbps
Control channel signaling data 
transmission speed: 64kbps
2ONCRC Synchronization Detection 
Timer is provided.
CRC Synchronization Detection 
Timer is not provided.
3ON
CRC4 Check is provided.
CRC4 Check is not provided.
(Continued)
0
ON
DOWN
4 
3 
2 
1 OFF
ON
OFF
OFF
OFF
OFF
1
23
45
67
8ONOFF
OFF
OFF 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIE (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 272ND-70928 (E), Issue 1.0
SW2 (DIP SW)
4Setting of control signal time slot
NOTE 2, NOTE 3 OFF
5
OFF
6
OFF
7
OFF
8ON
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
45
67
8ON
ON
SWITCH NUMBER
TIME SLOT
NUMBER
45678
OFFONONONON TS 1
ON OFF ON ON ON TS 2
OFF OFF ON ON ON TS 3
ON ON OFF ON ON TS 4
OFF ON OFF ON ON TS 5
ON OFF OFF ON ON TS 6
OFF OFF OFF ON ON TS 7
ON ON ON OFF ON TS 8
OFF ON ON OFF ON TS 9
ON OFF ON OFF ON TS 10
OFF OFF ON OFF ON TS 11
ON ON OFF OFF ON TS 12
OFFONOFFOFFON TS 13
ON OFF OFF OFF ON TS 14
OFF OFF OFF OFF ON TS 15
ON ON ON ON OFF TS 16
OFFONONONOFF TS 17
ON OFF ON ON OFF TS 18
OFF OFF ON ON OFF TS 19
ON ON OFF ON OFF TS 20
OFF ON OFF ON OFF TS 21
ON OFF OFF ON OFF TS 22
OFF OFF OFF ON OFF TS 23
ON ON ON OFF OFF TS 24
OFF ON ON OFF OFF TS 25
ON OFF ON OFF OFF TS 26
OFF OFF ON OFF OFF TS 27
OFF ON OFF OFF OFF TS 29
ON OFF OFF OFF OFF TS 30
OFF OFF OFF OFF OFF TS 31
ON
ON
ON
OFF 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIE (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 273
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card.
NOTE 2:
The time slot number 0 and 28 (TS0/28) cannot be used for control signal.
NOTE 3:
This setting must be identical with the opposite DAID card. SW3 (DIP SW) 1
Always set to ON
2
Always set to ON
3
Always set to ON
4
Always set to OFF
JPS (Jumper pin) Balanced transmission: 120 ohms
(For twisted-pair cable)
LeftTA is grounded on the transmission
line: 75 ohms (For coaxial cable)
JPR (Jumper pin)
RightRA is grounded on the transmission
line: 75 ohms (For coaxial cable)
Balanced transmission: 120 ohms
(For twisted-pair cable)
E1Z (Jumper pin)
RightLine impedance: 75 ohms (For coax-
ial cable)
Line impedance: 
120 ohms (For twisted-pair cable)
SRT (Jumper pin)
RightLine impedance: 
75 ohms (For coaxial cable)
Line impedance: 
120 ohms (For twisted-pair cable)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
4ON
ON
ON
ON
OFF
Right
Left
Left
Left 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIF (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 274ND-70928 (E), Issue 1.0
PN-DAIF (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Remains lit when the following connection are normal.
Control channel link between the DAID card and DAIE card.
Connection between the opposite DAIF card.
Goes out after 15 seconds of link disconnection.
RMT Red Remains lit when receiving the alarm signal from a distant office.
LOOP–Not used
PWR Red Remains lit when detecting PCM signal loss.
(Only on the DAIF card mounted on the Main Site.)
BL–Not used
SW2
SW3TBUS
RBUS
CNRU N
MB
LINK
RMT 
LOOP 
PWR 
BL
JPS
JPR JP
SW1