NEC Neax 2000 Ivs2 Installation Procedure Manual
Have a look at the manual NEC Neax 2000 Ivs2 Installation Procedure Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-M537 (EXPMEM) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 315 Lamps Indications This card has no lamps. Switch Settings The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW (DIP SW) 1For normal operation (Memory backup ON) OFFNot used (Memory backup OFF) 2 Not used 3 Not used 4 Not used 1 23 4ON ON OFF OFF OFF
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-M537 (EXPMEM) NEAX2000 IVS2 Installation Procedure ManualPage 316ND-70928 (E), Issue 1.0 Mounting PZ-M537 Card When mounting the EXPMEM card on the AP00/MP card, do the following procedure. STEP 1: Take off three screws from the rear side of EXPMEM suppor t. NOTE: Supports and screws are attached to the EXPMEM card. STEP 2: Connect the CONNR connector on the EXPMEM card and the CONN connector on the AP00/MP card. STEP 3: Secure the EXPMEM card to the AP00/MP card with three screws which taken by STEP 1. SUPPORT EXPMEM CARD EXPMEM CARD CONNR CONNECTOR WHEN MOUNTING EXPMEM CARD ON THE AP00 CARDWHEN MOUNTING EXPMEM CARD ON THE MP CARD AP00 CARD CONN CONNECTOR EXPMEM CARD CONNR CONNECTOR MP CARD CONN CONNECTOR
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-M542 (CONN) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 317 PZ-M542 (CONN) Locations of Lamps, Switches, and Connectors Lamp Indications This card has no lamps. JP2 RCV21 FOR No.2 CIRCUIT LT CJP1LTTO LTC CONNECTOR ON BWB IN PIM TO CHAMP CONNECTOR (MDF) JP0 TRS21 TRS01 FOR No.0 CIRCUIT COAXIAL CONNECTORRCV01 RCV11 FOR No.1 CIRCUITTRS11
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-M542 (CONN) NEAX2000 IVS2 Installation Procedure ManualPage 318ND-70928 (E), Issue 1.0 Switch Settings The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK JP0 For coaxial connectors (No. 0 circuit) LEFTFor champ connector (LT connector) (No. 0 circuit) JP1 For coaxial connectors (No.1 circuit) LEFTFor champ connector (LT connector) (No.1 circuit) JP2 For coaxial connectors (No. 2 circuit) LEFTFor champ connector (LT connector) (No. 2 circuit)RIGHT RIGHT RIGHT
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-M557 (CONN) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 319 PZ-M557 (CONN) Locations of Lamps, Switches, and Connectors Lamp Indications This card has no lamps. JP2 RCV20 FOR No.2 CIRCUIT LT CJP1LTTO LTC CONNECTOR ON BWB IN PIM TO CHAMP CONNECTOR (MDF) JP0 TRS20 TRS00 FOR No.0 CIRCUIT COAXIAL CONNECTORRCV00RCV10 FOR No.1 CIRCUIT TRS10
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-M557 (CONN) NEAX2000 IVS2 Installation Procedure ManualPage 320ND-70928 (E), Issue 1.0 Switch Settings The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK JP0 For coaxial connectors (No. 0 circuit) LEFTFor champ connector (LT connector) (No. 0 circuit) JP1 For coaxial connectors (No. 1 circuit) LEFTFor champ connector (LT connector) (No. 1 circuit) JP2 For coaxial connectors (No. 2 circuit) LEFTFor champ connector (LT connector) (No. 2 circuit)RIGHT RIGHT RIGHT
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS Line/Trunk Card NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 321 LINE/TRUNK CARD The table below shows the line/trunk cards to be explained in this section. Table 3-3 List of Line/Trunk Cards NAME (FUNCTIONAL NAME)LAMP X: PROVIDED –:NOT PROVIDEDSWITCH X: PROVIDED –:NOT PROVIDEDEXTRACTION/ INSERTION WITH POWER ON X: ALLOWED : ALLOWED AFTER MB* –: NOT ALLOWEDREFERENCE PA G E PN-2AMPA (AMP) X–XPage 324 PN-AUCA (AUC) X–XPage 325 PN-CFTA (CFT) X–XPage 326 PN-CFTB (CFT) X–XPage 327 PN-2COTD (COT) X–XPage 328 PN-4COTA-A (COT) X–XPage 329 PN-4COTB (COT) X–XPage 330 PN-4COTE (COT) X–XPage 331 PN-4COTF (COT) X–XPage 332 PN-4COTG (COT) X–XPage 333 PN-6COTJ (COT) X–XPage 334 PN-8COTQ (COT) X–XPage 335 PN-8COTR (COT) X–XPage 336 PN-8COTS (COT) X–XPage 337 PN-8COTT (COT) X–XPage 338 PN-2CSIA (CSI) X–XPage 339 PN-2CSIA-A (CSI) X X XPage 342 PN-4DATC (DAT) XX XPage 345 *MB = Make Busy
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS Line/Trunk Card NEAX2000 IVS2 Installation Procedure ManualPage 322ND-70928 (E), Issue 1.0 PN-2DITA (DIT) X–XPage 346 PN-4DITB (DIT) X–XPage 347 PN-DK00 (DK) ––XPage 348 PN-2DLCB/2DLCN (DLC)X–XPage 349 PN-2DLCC (DLC) X–XPage 350 PN-4DLCF (DLC) X–XPage 351 PN-4DLCM (DLC) X–XPage 352 PN-4DLCQ (DLC) X–XPage 353 PN-8DLCL (DLC) X–XPage 354 PN-8DLCP (DLC) X–XPage 355 PN-2DPCB (DPC) XX XPage 356 PN-2ILCA (ILC) XX XPage 360 PN-4LCC (LC) X–XPage 363 PN-4LCD-A (LC) X–XPage 364 PN-4LCE (LC) X–XPage 365 PN-4LCF (LC) X–XPage 366 PN-4LCK (LC) X–XPage 367 PN-4LCL (LC) X–XPage 368 PN-4LCV (LC) X–XPage 369 PN-4LCW (LC) X–XPage 370 PN-8LCAA (LC) X–XPage 371 *MB = Make Busy Table 3-3 List of Line/Trunk Cards (Continued) NAME (FUNCTIONAL NAME)LAMP X: PROVIDED –:NOT PROVIDEDSWITCH X: PROVIDED –:NOT PROVIDEDEXTRACTION/ INSERTION WITH POWER ON X: ALLOWED : ALLOWED AFTER MB* –: NOT ALLOWEDREFERENCE PA G E
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS Line/Trunk Card NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 323 PN-2LDTA (LDT) X–XPage 372 PN-M03 (M03) XX XPage 373 PN-M10 (M10) XXPage 376 PN-2ODTA (ODT) X–XPage 378 PN-2ODTB (ODT) X–XPage 379 PN-8RSTA (PBR) ––XPage 380 PN-TNTA (TNT) –XXPage 381 PN-4VCTH (VCT) XX XPage 383 PZ-8PFTB (PFT) ––XPage 385 PZ-VM00-M (VM) XXPage 386 PN-VM01 (VM) XX–Page 389 *MB = Make Busy Table 3-3 List of Line/Trunk Cards (Continued) NAME (FUNCTIONAL NAME)LAMP X: PROVIDED –:NOT PROVIDEDSWITCH X: PROVIDED –:NOT PROVIDEDEXTRACTION/ INSERTION WITH POWER ON X: ALLOWED : ALLOWED AFTER MB* –: NOT ALLOWEDREFERENCE PA G E
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2AMPA (AMP) NEAX2000 IVS2 Installation Procedure ManualPage 324ND-70928 (E), Issue 1.0 PN-2AMPA (AMP) Locations of Lamps, Switches, and Connectors Lamp Indications Switch Settings This card has no switches. LAMP NAMECOLOR FUNCTION BL0, 1 RedRemains lit when the corresponding circuit is in use. Flashes at 60 IPM when the corresponding circuit is in make- busy state or the system data for this card is not assigned. BL1 BL0