NEC Neax 2000 Ivs2 Installation Procedure Manual
Have a look at the manual NEC Neax 2000 Ivs2 Installation Procedure Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 5 CHAPTER 1 GENERAL INFORMATION This chapter explains the outline of system configuration, the name and functions of equipment, the line conditions of each terminal, and the mounting conditions of circuit cards used in the system.
CHAPTER 1 GENERAL INFORMATION Trunking Diagram NEAX2000 IVS2 Installation Procedure ManualPage 6ND-70928 (E), Issue 1.0 TRUNKING DIAGRAM This figure shows a typical trunking diagram for the system. Figure 1-1 Trunking Diagram NOTE: The equipment marked with (*) is provided by the customer INCLUDING TDSW DTG PBSND 16CFT MLDT PLO MEM MODEM PBR DAT DK TNT SMDR MP PFT PFTCOT C.O. LINE AUC/DIT AMP DID LINE LDT ODT TIE LINE DIGITAL LINK ODT DTI CCH DCH VCT IPT ICH M10 LC LONG LINE STATIONSINGLE LINE TEL SINGLE LINE TEL WITH MESSAGE WAITING LAMP AU C LC ILC DLC DLC DLC DLC EXPMEM VM AP00 ETHER DPC COT PSTN ROUTER DTI/REMOTE PIM OPTICAL FIBER PBR DAT CIR MFR CFT DK COT COT COT/TNT TNT BRT ISDN NETWORK IP NETWORK 6/10 PARTY CONFERENCE COT EXTERNAL HOLD TONE(*) ANNOUNCEMENT MACHINE(*) EXTERNAL HOLD TONE(*) SPEAKER(*) AMPLIFIERKEY(*) (*) BGM CSI Dterm DSS LONG LINE D term ATTCON (4 wire) ATTCON (2 wire)/ DESKCON SMDR PMS AD-8 PS CS/ZT PC FOR OAIRS-232C RS-232CV. 1 1 TCP/IP RS-232C PC FOR OAI DTE M03RS-232CV. 3 5 DTE MAT MAT CIS/HOTEL PRINTER ISDN TERMINAL (FOR REMOTE MAINTENANCE) DSS2W E&MLD 4W E&M PRT AP01
CHAPTER 1 GENERAL INFORMATION Trunking Diagram NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 7 SYMBOL DESCRIPTION SYMBOL DESCRIPTION AMP Amplifier Trunk Card KEY External Key AP00 SMDR/Hotel Application Card LC Line Circuit Card (for Single Line Telephone) AP01 OAI Interface Card LDT LD Trunk Card AUC Analog Universal Circuit Card (Long Line Circuit, DID Trunk)M03 V.35 DTE Interface Card BGM External Music Source for D term Back Ground Music ServiceM10 Optical Interface Card BRT Basic Rate Interface Trunk Card MAT Maintenance Administration Terminal CCH Common Channel Handler Card MDF Main Distribution Frame CFT 6/10 Party Conference Trunk Card MEM Main Memory CIS Call Information System MFR MF Receiver/ MFC Receiver/Sender Card CIR CALLER ID Receiver Trunk Card MLDT Melody Trunk COT C.O. Trunk Card MODEM Modem CSI CS/ZT Interface Card MP Main Processor Card CS/ZT Cell Station (For Australia/Others) Zone Transceiver (For North America/ Latin America)PFT Power Failure Transfer DAT Digital Announcement Trunk Card PMS Property Management System DCH D-channel Handler Card OAI Open Application Interface DIT DID Trunk Card ODT OD Trunk Card (2/4 wire E&M) DK External Relay/Key Interface Card PBR PB Receiver Card DLC Digital Line Circuit Card (for D term, ATTCON, DESKCON)PBSND PB Sender DPC Data Port Controller Card PLO Phase Locked Oscillator DSS DSS Console PS Personal Station DTE Data Terminal Equipment PRT ISDN Primary Rate Interface Trunk Card DTI Digital Trunk Interface Card SMDR Station Message Detail Recording DTG Digital Tone Generator TDSW Time Division Switch ETHER Ethernet Control Card TNT Tone/Music Source Interface Card EXPMEM Memory Expansion Card VCT CODEC Card ICH ISDN-channel Handler Card VM Voice Mail Card ILC ISDN Line Circuit Card 16CFT 16 Circuit Four Party Conference Trunk IPT IP Trunk Card KEY External Key
CHAPTER 1 GENERAL INFORMATION System Configuration NEAX2000 IVS2 Installation Procedure ManualPage 8ND-70928 (E), Issue 1.0 SYSTEM CONFIGURATION The system provides three installation methods as follows: Floor Standing Installation Wall Mounting Installation 19-inch Rack Mounting Installation Example of system configurations for each installation method is shown below. Floor Standing Installation Figure 1-2 1-PIM Configuration for Floor Standing Installation PIM BASE FRONT 223 (8.8) 430 (16.9) 416.6 (16.4) UNIT : mm (inch)
CHAPTER 1 GENERAL INFORMATION Floor Standing Installation NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 9 Figure 1-3 2-PIM Configuration for Floor Standing Installation PIM/BATTM BASE FRONT PIM 223 (8.8) 430 (16.9) 768.6 (30.2) UNIT : mm (inch)
CHAPTER 1 GENERAL INFORMATION Floor Standing Installation NEAX2000 IVS2 Installation Procedure ManualPage 10ND-70928 (E), Issue 1.0 Figure 1-4 Maximum Configuration for Floor Standing Installation 223 (8.8) 860 (33.9) 1472.6 (58.0) 1824.6 (71.8) BATTM PIM4 PIM5 PIM6 PIM7 BATTMPIM0 PIM1 PIM2 PIM3 BASE FRONT
CHAPTER 1 GENERAL INFORMATION Wall Mounting Installation NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 11 Wall Mounting Installation Figure 1-5 1-PIM Configuration for Wall-Mounting Installation PIM BASE
CHAPTER 1 GENERAL INFORMATION 19-inch Rack Mounting Installation NEAX2000 IVS2 Installation Procedure ManualPage 12ND-70928 (E), Issue 1.0 19-inch Rack Mounting Installation Figure 1-6 1-PIM Configuration for 19-inch Rack Mounting Installation BASE19” BRACKET 19-inch RACK
CHAPTER 1 GENERAL INFORMATION Equipment Name and Function NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 13 EQUIPMENT NAME AND FUNCTION This section explains the names and functions of the equipment (modules, installation hardware, circuit cards) used in the system. Module/Installation Hardware This table shows the names and functions of the modules. Table 1-1 Module Name and Function EQUIPMENT NAMEFUNCTIONAL NAMEFUNCTION SN1480 PIMAFPIM Port Interface Module (PIM) Max. 64 physical ports per PIM. Houses two batteries for protection from short power interruption (for 30 minutes). At maximum configuration, the system consists of eight PIMs and provides a total of 512 physical ports (64 ports x 8). SN1545 BASEREBASE/TOP ASSEMBase/Top Cover Assembly One base and top cover assembly is required for each stack. TOP COVER ASSEM SN1526 BATTMFBATTM Battery Module for housing PIM or CS (ZT) backup batteries Houses two pairs of batteries for protection from long power interruption (for 3 hours).
CHAPTER 1 GENERAL INFORMATION Module/Installation Hardware NEAX2000 IVS2 Installation Procedure ManualPage 14ND-70928 (E), Issue 1.0 This table shows the names and functions of installation hardware. Table 1-2 Installation Hardware Name and Function EQUIPMENT NAMEFUNCTIONAL NAMEFUNCTION HANGER ASSEM (B) Wall Hanger Assembly One HANGER ASSEM per PIM is required for Wall Mounting Installation. MOUNTING BRACKET Safety Mounting Bracket Used as an overhead hanger for Floor Standing Installation. Wire, chain or eyebolts to secure the bracket are to be locally provided. To be installed on the top PIM in four or more modules of stack. It provides 1.1G shockproof construction. 19” RACK BRACKET (A) 19-inch Rack Mounting Bracket Type A One bracket is required for one PIM configuration. One bracket is required for the top PIM in a multiple module configuration. 19” RACK BRACKET (B) 19-inch Rack Mounting Bracket Type B One bracket is required for the bottom module in a multiple module configuration. I/F BRACKET ASSEM Inter Frame Bracket Assembly Used to joint the frames in two-frame configuration; for Floor Standing Installation. BASE TRAY ASSEM Base Tray Assembly One BASE TRAY is required per one frame for Floor Standing Installation of Stationary Equipment.