NEC Neax 2000 Ivs2 Installation Procedure Manual

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-AP01 (AP01)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 235
PN-AP01 (AP01)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
L0-L3 L3 Green Indication of CTS signal status on RS-232C port.
L2 Indication of DCD signal status on RS-232C port.
L1 Indication of TXD signal status on RS-232C port.
L0 Indication of RXD signal status on RS-232C port.
RS0
SENSE
RUN
MB
SW1
L3 
L2 
L1 
L0
SW0
IP
J19 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-AP01 (AP01)
NEAX2000 IVS2 Installation Procedure ManualPage 236ND-70928 (E), Issue 1.0
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-15) to
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW1
(Piano Key SW)
1For normal operation
OFF Not used
2For normal operation
OFF Not used
3For normal operation
OFF Not used
4For normal operation
OFF Not used
(Continued)
F
4AP No.04 05 06 07 08 09 10 11 12 13 14 15
SW No.456789ABCDEF
ON
DOWN
4 
3 
2 
1 OFF
ON
ON
ON
ON
ON 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-AP01 (AP01)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 237
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card. SW0 (DIP SW)
1ON Receives RT clock
Uses internal clock
2ON Receives ST2 clock
Uses internal clock
3ON Sends ST1 clock
Not send ST1 clock
4 Not used 
J19
For normal operation
(Memory backup ON)
LEFTNot used 
(Memory backup OFF)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
4ONOFF
OFF
OFF
OFF
Front (Jumper pin)
RIGHT 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-BRTA (BRT)
NEAX2000 IVS2 Installation Procedure ManualPage 238ND-70928 (E), Issue 1.0
PN-BRTA (BRT)
Locations of Lamps, Switches, and Connectors
SENSE
RUN
MB
SW1
SW0B1
B2
D
ALM 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-BRTA (BRT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 239
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
B1 Green B1 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
B2 Green B2 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
D Green D channel status
ON: Busy
OFF: Idle
ALM Red Transmission line fault status
ON: Line fault
OFF: Normal operation 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-BRTA (BRT)
NEAX2000 IVS2 Installation Procedure ManualPage 240ND-70928 (E), Issue 1.0
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-15) to
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW0 (DIP SW)
1For normal operation 
OFF Not used
2
NOTE 3
NOTE 4ONSource clock signal from network is 
sent to the PLO of MP according to 
the switch setting of SW0-3.
OFFSource clock signal from network is 
not sent to the PLO of MP card.
3
NOTE 3
NOTE 4ONClock signal is sent to the PLO 0 of 
MP.
OFFClock signal is sent to the PLO 1 of 
MP.
4For normal operation
OFF Not used
(Continued)
AP No.04 05 06 07 08 09 10 11 12 13 14 15
SW No.456789ABCDEF
ON
DOWN
1
23
4ON
ON
ON 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-BRTA (BRT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 241
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card. SW1 (DIP SW)
1For terminating the transmitting side 
of channels B1 and B2 with 100 
ohms.
OFFTo remove the terminating resistor 
on the transmitting side of channels 
B1 and B2.
2For terminating the receiving side of 
channels B1 and B2 with 100 ohms.
OFFTo remove the terminating resistor 
on the receiving side of channels B1 
and B2.
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
2ONON
ON 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-BRTA (BRT)
NEAX2000 IVS2 Installation Procedure ManualPage 242ND-70928 (E), Issue 1.0
NOTE 3:
Set the SW0-2 and SW0-3 as follows:
NOTE 4:
When the system is a clock source office, set the SW0-2 and SW0-3 on all the BRT
cards mounted in PIM0 to “OFF”.
NOTE 5:
Mount the BRT card which receives a source clock signals into PIM0. CONDITIONSBRT0 BRT1 BRT2 ---- BRT11
REMARKS
SW
0-2SW
0-3SW
0-2SW
0-3SW
0-2SW
0-3----SW
0-2SW
0-3
When one 
BRT is 
provided.ON ONMP card will receive the 
clock signal from BRT0 at 
its PLO0 input.
When more 
than one BRT 
is provided.ON ON ON OFF OFF ON ---- OFF ONMP card will receive the 
clock signal from BRT0 at 
its PLO0 input, under nor-
mal conditions.
Should a clock failure occur 
with BRT0, MP card will 
switch to the PLO1 input 
which gets clock from 
BRT1. 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2BRTC (BRT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 243
PN-2BRTC (BRT)
Locations of Lamps, Switches, and Connectors
SENSE
RUN
MB
B21 
B11 
D1 
ALM1 
B20 
B10 
D0 
ALM0
SW0 SW11
SW10 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2BRTC (BRT)
NEAX2000 IVS2 Installation Procedure ManualPage 244ND-70928 (E), Issue 1.0
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
B21 Red No.1 Circuit B2 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
B11 Red B1 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
D1 Green D channel status
ON: Busy
OFF: Idle
ALM1 Red Transmission line fault status
ON: Line fault
OFF: Normal operation
B20 Red No.0 Circuit B2 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
B10 Red B1 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
D0 Green D channel status
ON: Busy
OFF: Idle
ALM0 Red Transmission line fault status
ON: Line fault
OFF: Normal operation