NEC Neax 2000 Ivs2 Installation Procedure Manual

							CHAPTER 2 INSTALLATION
Procedure
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 45
PROCEDURE
This flowchart explains the procedures for installing the PBX system. Follow the procedures in
Figure 2-2.
Figure 2-2  Procedure Flowchart (1 of 2)
START
UNPACKING
INSTALLATION
OF
MAIN EQUIPMENT
BATTERY
CONNECTION
TERMINATION OF
CABLES ON MDF SUPPLY VOLTAGE CHECK
AND
HEAT RUN TEST
CABLE RUNNING
TO MDF
INSTALLATION
OF
PERIPHERAL EQUIPMENT
A POWER CABLE
CONNECTION
SWITCH SETTINGS
OF
CIRCUIT CARDSREFER TO CHAPTER 3.
 Page 49
 Page 54
 Page 83
 Page 90
 Page 94
 Page 102
 Page 109
Page 128
WIRING AC CABLE
TO
TERMINALS Page 50 
						

							CHAPTER 2 INSTALLATION
Procedure
NEAX2000 IVS2 Installation Procedure ManualPage 46ND-70928 (E), Issue 1.0
Figure 2-2  Procedure Flowchart (2 of 2)
For Floor Standing Installation, there are three methods to install the equipment. It depends on
the country according to the UL/cUL/ACA.
NOTE:
UL = Underwriters Laboratories (U.S.A.)
cUL = Canadian Underwriters Laboratories (Canada)
ACA = Australian Communication Authority (Australia)
“Stationary Equipment (For North America/ Australia)”
“Fixed Equipment (For Nor th America/ Australia)”
“Fixed Equipment (For Other Countries)”
A
END MOUNTING
MOUNTING FRONT COVERCIRCUIT CARDS
SYSTEM
SYSTEM DATA ENTRY
CLEANING
AND
VISUAL CHECK INITIALIZATION
OPERATION TEST
SYSTEM DATA SAVE
 Page 199
Page 201
 Page 202
Page 204
Page 205
Page 205
  
						

							CHAPTER 2 INSTALLATION
Stationary Equipment (For North America/Australia)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 47
Stationary Equipment (For North America/Australia)
The equipment is placed on the BASE TRAY which is fixed on the floor, and is connected to 120V/
240V AC Power Source using AC CORD-D cable.
For installation of Stationary Equipment, see the following pages.
WIRING AC CABLE TO TERMINALS - Using AC CORD-D  Page 50
INSTALLATION OF MAIN EQUIPMENT - Floor Marking for BASE TRAY  Page 58
- Installation of PIM, For Stationary Equipment  
Page 55
Fixed Equipment (For North America/Australia)
The equipment is fixed on the floor by BASE PLATE and anchor bolts, and is connected to AC
Power Distribution Board using installation cable.
For installation of this equipment, see the following pages.
WIRING AC CABLE TO TERMINALS - Using installation Cable  Page 52
INSTALLATION OF MAIN EQUIPMENT - Floor Marking for BASE PLATE  Page 58
- Installation of PIM, For Fixed Equipment
 Page 55
Fixed Equipment (For Other Countries)
The equipment is fixed on the floor by BASE PLATE and anchor bolts, and is connected to 120V/
240V AC Power Source using AC CORD-D cable.
For installation of this equipment, see the following pages.
WIRING AC CABLE TO TERMINALS - Using AC CORD-D  Page 50
INSTALLATION OF MAIN EQUIPMENT - Floor Marking for BASE PLATE  Page 58
- Installation of PIM, For Fixed Equipment
 Page 55 
						

							CHAPTER 2 INSTALLATION
Fixed Equipment (For Other Countries)
NEAX2000 IVS2 Installation Procedure ManualPage 48ND-70928 (E), Issue 1.0
The mark shown below is attached to each procedure in which circuit cards are handled. When
doing such a procedure, the installer must perform the procedure with caution, to prevent dam-
age caused by static electricity (See “Static Electricity Guard”on Page 39
).
ATTENTION
Contents
Static Sensitive
Handling
Precautions Required 
						

							CHAPTER 2 INSTALLATION
Unpacking
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 49
UNPACKING
(1) Check the received quantity of packages containing the PBX system with the description on 
the shipping document.
(2) Check the packaging for external damage done by transportation and record it as 
necessary.
(3) Unpack the packaging.
For unpacking the packages containing circuit cards, a grounded wrist strap should be 
worn.
(4) Check the quantity of equipment and materials unpacked with the shipping document.
(5) Perform visual inspection, checking for the following items.
PIMs Overall distor tion.
Scratches and dents on the surface.
Scratches and cracks on the PIM Backplane.
Broken or bent pins on the PIM Backplane.
Covers Scratches and dents.
Circuit Cards Overall distor tion
Scratches and cracks
Loss, or damage of par ts on the circuit cards.
Attendant Console Scratches and cracks on the keyboard
Overall distor tion
Damage to Keys and lamps.
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							CHAPTER 2 INSTALLATION
Wiring AC Cable to Terminals
NEAX2000 IVS2 Installation Procedure ManualPage 50ND-70928 (E), Issue 1.0
WIRING AC CABLE TO TERMINALS
There are two kinds of AC cable : AC CORD-D For Stationary Equipment/Fixed Equipment (For
Other Countries)
: Installation Cable For Fixed Equipment (For North America/
Australia)
Using AC CORD-D
(1) Take the AC CORD-D out of the hole on the left side of the BASE, then secure the code to 
the BASE with the cord bush.
NOTE:
Cord bush is attached to the AC CORD-D.
(2) Wire the AC CORD-D and the FG cable to the FG, NEUTRAL, LINE and Ground terminals 
on the BASE.
(3) Wire the  AC CORD-B to the FG, NEUTRAL and LINE terminals on the BASE.
Figure 2-3  Wiring AC CORD to Terminals
NOTE:
Cable colors in the parentheses are for Australia.
FG CABLE 
(GREEN)
HOW TO SECURE CABLES TO TERMINAL BLOCK
INSERT A SCREW DRIVER INTO THE INSIDE HOLE OF TERMINAL BLOCK.
PULL DOWN THE SCREW DRIVER TOWARD INSIDE AND OPEN THE METAL PLATE.
INSERT A POWER CABLE INTO THE OUTSIDE HOLE OF TERMINAL BLOCK.
REMOVE THE SCREW DRIVER. 1 12
2 33
4 4
AC CORD-B
AC CORD-D TO
120V/240V
AC POWER
SOURCETO CN1 on
PZ-PW121 in PIM
FG
NEUTRALLINETERMINAL
BLOCKS GREEN
(GREEN/YELLOW)BLACK (BROWN)
BLACK (BROWN)
WHITE (BLUE)
GREEN
(GREEN/YELLOW)WHITE (BLUE)
BASE
FRONT 
						

							CHAPTER 2 INSTALLATION
Using AC CORD-D
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 51
(4) When the system is two-frame configuration, the AC CORD-D of the right side frame can 
go through the BASE of the left side frame.
Figure 2-4  AC CORD Wiring for Two-Frame Configuration
BASE
FGLINENEUTRALFGLINENEUTRAL
TERMINAL
BLOCKS TO
120V/240V AC
POWER SOURCE
AC CORD-D
CORD BUSH 
						

							CHAPTER 2 INSTALLATION
Using Installation Cable
NEAX2000 IVS2 Installation Procedure ManualPage 52ND-70928 (E), Issue 1.0
Using Installation Cable
(1) Take the Installation cable out of the hole on the left side of the BASE, then secure the cable 
to the BASE with the cord bush.
NOTE:The installer is to use minimum 16 AWG (1.3
φ) size wire, maximum 9 mm size
cable.
(2) Wire the Installation cable and the FG cable to the FG, NEUTRAL, LINE and Ground 
terminals on the BASE.
(3) Wire the  AC CORD-B to the FG, NEUTRAL and LINE terminals on the BASE.
Figure 2-5  Wiring Installation Cable to Terminals
NOTE:Cable colors in the parentheses are for Australia.
FG CABLE 
(GREEN)
HOW TO SECURE CABLES TO TERMINAL BLOCK
INSERT A SCREW DRIVER INTO THE INSIDE HOLE OF TERMINAL BLOCK.
PULL DOWN THE SCREW DRIVER TOWARD INSIDE AND OPEN THE METAL PLATE.
INSERT A POWER CABLE INTO THE OUTSIDE HOLE OF TERMINAL BLOCK.
REMOVE THE SCREW DRIVER. 112
23
3
4
4
AC CORD-B
INSTALLATION CABLE TO AC
POWER
DISTRIBUTION
BOARDTO CN1 on
PZ-PW121 in PIM
FG NEUTRAL LINETERMINAL
BLOCKS GREEN
(GREEN/YELLOW)BLACK (BROWN)
BLACK (BROWN)
WHITE (BLUE)
GREEN
(GREEN/YELLOW)WHITE (BLUE)
BASE
FRONT 
						

							CHAPTER 2 INSTALLATION
Using Installation Cable
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 53
(4) When the system is two-frame configuration, the Installation cable of the right side frame 
can go through the BASE of the left side frame.
Figure 2-6  Installation Cable Wiring for Two-Frame Configuration
BASE
FGLINENEUTRALFGLINENEUTRAL
TERMINAL
BLOCKS TO
AC POWER
DISTRIBUTION
BOARD
INSTALLATION CABLE
CORD BUSH 
						

							CHAPTER 2 INSTALLATION
Installation of Main Equipment
NEAX2000 IVS2 Installation Procedure ManualPage 54ND-70928 (E), Issue 1.0
INSTALLATION OF MAIN EQUIPMENT
Floor Standing Installation

Check the site for installing the PBX with the work drawing to verify that 
the required floor space is ensured and that service entrances and 
ducts for trunk/extension cables, power cables and bus cables have 
been properly worked at correct positions. See Figure 2-7 and Figure 
2-8.

Mark positions for installation of the PBX main equipment.
For Fixed Equipment, detach the BASE PLATE from the BASE. See  
Figure 2-9.
For Stationary Equipment, see Figure 2-10.
NOTE:
Measure the level of the floor surface before installing the PBX
main equipment.

Check the level of the floor. If necessary, adjust the level by inserting 
spacers beneath the equipment.

First open necessary number of preliminary prepared holes using the 
drill bit for small-diameter holes, then use the finishing drill bit for fin-
ishing drill holes. See “Drilling” on Page 59.

Detach the front cover of each PIM. See “Detaching FRONT COVER” 
on Page 60
.
Start 
Checkup
before installation
Marking
Leveling
Detaching Front Cover
Drilling
A