NEC Neax 2000 Ivs2 Installation Procedure Manual
Have a look at the manual NEC Neax 2000 Ivs2 Installation Procedure Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIA (DAI) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 255 The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1: Set the groove on the switch to the desired position. NOTE 2: When the power is on, flip the MB switch to ON (UP position) before plugging/unplug- ging the circuit card. SW3 (DIP SW) 1Set the equalizer according to the cable length between the system and the CSU. OFF 2 OFF 3 OFF 4 Always set to OFF JPS (Jumper pin) RightFor mounting this card on PIM1 - PIM7 LeftFor mounting this card on PIM0 JPR (Jumper pin) RightNeutral grounding on the receiving line is provided. Neutral grounding on the receiving line is not provided. (Continued) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK 1 23 4ON ON SW -1SW -2SW -3CABLE LENGTH ON ON ON0 - 40m (0-131.2ft.) ON ON OFF40 - 80m (131.2-262.5ft.) ON OFF ON80 - 120m (262.5-394ft.) ON OFF OFF120 - 160m (394-525ft.) OFF ON ON160 - 200m (525-656ft.) OFF OFF OFF Signal is not sent ON ON OFF Left
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIA (DAI) NEAX2000 IVS2 Installation Procedure ManualPage 256ND-70928 (E), Issue 1.0 NOTE 3: When clock source office signal is supplied via the line between the main site and the remote site, set the SW1-1 and SW1-2 as the following table. In this case, DAIA cards (DAIA0, DAIA1) must be mounted in PIM0. NOTE 4: The time slot number 0, 20, 21, and 22 (TS0/20/21/22) cannot be used for control sig- nal. NOTE 5: This setting must be identical with the opposite DAIB card. CONDITIONSDAIA0 DAIA1 DAIA2 REMARKS SW 1-1SW 1-2SW 1-1SW 1-2SW 1-1SW 1-2 One DAIA card is provided.ON OFF––––The clock signal is sent to PLO0 of MP card via supply route 0 (DAIA0). Two or three DAIA cards are provided.ON OFF OFF ON OFF OFF The clock signal sup- ply route is automati- cally changed to the route 1 (DAIA1), if a transmission line fail- ure occurs on the supply route 0.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIB (DAI) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 257 PN-DAIB (DAI) Location of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. LINK Green Remains lit when a link between this card and a distant office is normally connected. Goes out after 15 seconds of link disconnection. RED Red Remains lit when detecting PCM signal loss or Frame Alignment signal loss. RMT Red Remains lit when receiving the alarm signal from a distant office. LOOP–Not used BL Red Remains lit while data transmission on control channel (D ch). Flashes while FP data downloading. JPS JPR SW2 SW3BUS CNSENSE RUN MB LINK RED RMT LOOP BL SW1
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIB (DAI) NEAX2000 IVS2 Installation Procedure ManualPage 258ND-70928 (E), Issue 1.0 Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENSE (Rotary SW) 0-FAlways set to 0 1-F Not used MB (Toggle SW) NOTE 1UP For make-busy For normal operation SW1 (Piano Key SW)1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4 Always set to OFF (Continued) 0 ON DOWN 4 3 2 1 OFF ON OFF OFF OFF OFF
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIB (DAI) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 259 SW2 (DIP SW) 1ONControl channel signaling data transmission speed: 48kbps Control channel signaling data transmission speed: 64kbps 2ONDTI frame configuration: 12-Multi Fram e DTI frame configuration: 24-Multi Fram e 3ON Line code: AMI with ZCS Line code: B8ZS 4ONSetting of control signal time slot NOTE 2, NOTE 3 5ON 6ON 7 OFF 8ON (Continued) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK 1 23 45 67 8ONOFF OFF OFF SWITCH NUMBER TIME SLOT NUMBER 45678 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFFON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF OFFON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFFON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ONON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFFTS1 TS2 TS3 TS4 TS5 TS6 TS7 TS8 TS9 TS10 TS11 TS12 TS13 TS14 TS15 TS16 TS17 TS18 TS19 TS23 OFF OFF OFF ON OFF
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIB (DAI) NEAX2000 IVS2 Installation Procedure ManualPage 260ND-70928 (E), Issue 1.0 The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1: When the power is on, flip the MB switch to ON (UP position) before plugging/unplug- ging the circuit card. NOTE 2: Time slot number 0, 20, 21, and 22 (TS0/20/21/22) can not be used for control signal. NOTE 3: This setting must be identical with the opposite DAIA card. SW3 (DIP SW) 1Set the equalizer according to the cable length between the system and the CSU. OFF 2 OFF 3 OFF 4 Always set to OFF JPS (Jumper pin) UPNeutral grounding on the transmit- ting line is provided. Neutral grounding on the transmit- ting line is not provided. JPR (Jumper pin) UPNeutral grounding on the receiving line is provided. Neutral grounding on the receiving line is not provided. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK 1 23 4ON ON SW -1SW -2SW -3CABLE LENGTH ON ON ON0 - 40m (0-131.2ft.) ON ON OFF40 - 80m (131.2-262.5ft.) ON OFF ON80 - 120m (262.5-394ft.) ON OFF OFF120 - 160m (394-525ft.) OFF ON ON160 - 200m (525-656ft.) OFF OFF OFF Signal is not sent ON ON OFF DOWN DOWN
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIC (DAI) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 261 PN-DAIC (DAI) Location of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. LINK Green Remains lit when the following connection are normal. Control channel link between the DAIA card and DAIB card. Connection between the opposite DAIC card. Goes out after 15 seconds of link disconnection. RED Red Remains lit when detecting PCM signal loss or Frame Alignment signal loss. RMT Red Remains lit when receiving the alarm signal from a distant office. LOOP–Not used PWR–Not used BL–Not used SW2 SW3TBUS RBUS CNRUN MB LINK RED RMT LOOP PWR BL SW1
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIC (DAI) NEAX2000 IVS2 Installation Procedure ManualPage 262ND-70928 (E), Issue 1.0 Switch Settings SWITCHNAME SWITCH NUMBER SETTING POSITION FUNCTION CHECK MB (Toggle SW) N OTE UP For make-busy For normal operation SW1 (Piano Key SW) 1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4 Always set to OFF SW2 (DIP SW) 1 Not used 2ON DTI frame configuration: 12-Multi Fram e DTI frame configuration: 24-Multi Fram e 3 ON Line code: AMI with ZCS Line code: B8ZS 4 Not used 5 Not used 6 Not used 7 Not used 8 Not used (Continued) ON DOWN 4 3 2 1 OFF ON OFF OFF OFF OFF 1 23 45 67 8ON OFF OFF OFF OFF OFF OFF OFF OFF
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAIC (DAI) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 263 The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE: When the power is on, flip MB switch to ON (UP position) before plugging/unplugging the circuit card. SW3 (DIP SW) 1Set the equalizer according to the cable length between the system and the CSU. OFF 2 OFF 3 OFF 4ONWhen mounting this card on remote site. OFFWhen mounting this card on main site. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK 1 23 4ON ON SW -1SW -2SW -3CABLE LENGTH ON ON ON0 - 40m (0-131.2ft.) ON ON OFF40 - 80m (131.2-262.5ft.) ON OFF ON80 - 120m (262.5-394ft.) ON OFF OFF120 - 160m (394-525ft.) OFF ON ON160 - 200m (525-656ft.) OFF OFF OFF Signal is not sent ON ON
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-DAID (DAI) NEAX2000 IVS2 Installation Procedure ManualPage 264ND-70928 (E), Issue 1.0 PN-DAID (DAI) Location of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. LINK Green Remains lit when a link between this card and a distant office is normally connected. Goes out after 15 seconds of link disconnection. RMT Red Remains lit when receiving the alarm signal from a distant office. LOOP–Not used PWR Red Remains lit when detecting PCM signal loss. BL Red Remains lit while data transmission on control channel (D ch). Remains lit while FP data downloading. SRT JPS E1Z JPR SW2 SW3BUS PCM1 PCM0 CNSENSE RUN MB SW1LINK RMT LOOP PWR BL JP