NEC Neax 2000 Ivs2 Installation Procedure Manual
Have a look at the manual NEC Neax 2000 Ivs2 Installation Procedure Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-8PFTB (PFT) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 385 PZ-8PFTB (PFT) Locations of Lamps, Switches, and Connectors Lamp Indications This card has no lamps. Switch Settings This card has no switches. PFT1 PFT0
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-VM00-M (VM) NEAX2000 IVS2 Installation Procedure ManualPage 386ND-70928 (E), Issue 1.0 PZ-VM00-M (VM) Location of Lamps, Switches, and Connectors CPU Board (Top Side) DSP Board (Bottom Side) BIOSHDD TXDRXD MODRI COM2 COM1 SW1-1SW1-4 CPU Board (top side) VM00-M Card Internal modem RST PL0PL3 DSP SWP BL0 BL7 CN3 (VM01 Card Slot) DSP Board (bottom side) MB VM00-M Card
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-VM00-M (VM) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 387 Lamp Indications LAMP NAMECOLOR FUNCTION CPU BoardRXD Green Not used TXD Red Not used MOD Green Not used RI Red Incoming call HDD Red Accessing to the HDD –Built-in hard disk is faulty BIOS Red BIOS programming is in operation –DOS mode has been activated DSP BoardBL0-7 RedRemains lit when the corresponding circuit is in use. Flashes at 60 IPM when the corresponding circuit is in make- busy state or the system data for this card is not assigned. SWP Red 30 seconds after the MB switch is turned ON (upward) (The cir- cuit card can be plugged/unplugged while this pilot lamp is on.) DSP Green/ FlashingAccording to voice mail application program in use. Red/ Flashing PL0-3 Red DSP circuit operating
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-VM00-M (VM) NEAX2000 IVS2 Installation Procedure ManualPage 388ND-70928 (E), Issue 1.0 Switch Settings The figure in the SWITCH NAME column and the position in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1: When the power is on, flip the MB switch to ON (UP position) before plugging/unplug- ging the circuit card. NOTE 2: When SW1 settings have changed, RST switch must be pushed. NOTE 3: Use BIOS Redirect only when assisted by NEC. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK MB (Toggle SW) NOTE 1UP For make-busy For normal operation RST (Toggle SW) NOTE 2Push when starting up this card, after MB switch is set to DOWN position. SW1 (Piano Key SW) NOTE 21ONBIOS Redirect Utility (Key board) NOTE 3 Normal Operation 2ONBIOS Redirect Utility (Floppy Drive) NOTE 3 Normal Operation 3ONCOM2: Use internal modem for remote maintenance OFFCOM2: RS-232C (For local direct connection to maintenance console) 4 Not used ON DOWN 4 3 2 1 OFF ON OFF OFF OFF
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PZ-VM01 (VM) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 389 PZ-VM01 (VM) Location of Lamps, Switches, and Connectors Lamp Indications Switch Settings This card has no switches. LAMP NAMECOLOR FUNCTION PL4-7 Red DSP circuit operating VM01 Card (on VM00 DSP Board)PL4PL7
NEAX2000 IVS2 Installation Procedure ManualPage 390 ND-70928 (E), Issue 1.0 This page is for your notes.