NEC Neax 2000 Ivs2 Installation Procedure Manual
Have a look at the manual NEC Neax 2000 Ivs2 Installation Procedure Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-M03 (M03) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 375 Switch Settings The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE: The JP1A and JP1B must be set to the same position each other. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW0 (DIP SW) 1 Always set to OFF 2 Not used JP1A (Jumper pin) NOTETXC(2) signal is sent out. Left TXC(2) signal is inputted. JP1B (Jumper pin) NOTETXC(2) signal is sent out. Left TXC(2) signal is inputted. OPSD (Jumper pin)RightSet the function of extending dis- tance for TXD signal. Cancel the function of extending distance for TXD signal. OPRS (Jumper pin)RightSet the function of extending dis- tance for RTS signal. Cancel the function of extending distance for RTS signal. OPER (Jumper pin)RightSet the function of extending dis- tance for DTR signal. Cancel the function of extending distance for DTR signal. 1 2ON OFF OFF Right Right Left Left Left
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-M10 (M10) NEAX2000 IVS2 Installation Procedure ManualPage 376ND-70928 (E), Issue 1.0 PN-M10 (M10) Location of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION CK0 Green Remains lit when a Digital Trunk Interface is connected to No. 0 circuit on this card. CK1 Green Remains lit when a Digital Trunk Interface is connected to No. 1 circuit on this card. TALM Red Remains lit when optical output is stopped. RALM Red Remains lit when optical input is lost or stopped. CN1 TO OPTICAL CABLECK0 CK1 TA L M RALMJP3 JP4 JP2 JP1 JP0
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-M10 (M10) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 377 Switch Settings NOTE 1: Set the groove on the switch to the desired position NOTE 2: When the power is on, flip the MB switch to ON (UP position) before plugging/unplug- ging the circuit card. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK JP0, 1 (Jumper pin)UPWhen connected to E1 (2M) Digital Trunk Interface. DOWNWhen connected to T1 (1.5M) Digi- tal Trunk Interface. JP2 (Jumper pin) RightLine code: B8ZS* is provided (For T1 interface) *B8ZS: Bipolar Eight zero Substitu- tion LeftLine code: B8ZS* is not provide (For T1 interface) *B8ZS: Bipolar Eight zero Substitu- tion JP3 (Jumper pin) RightWhen connected to E1 (2M) Digital Trunk Interface. LeftWhen connected to T1 (1.5M) Digi- tal Trunk Interface. JP4 (Jumper pin) UPWhen connected to E1 (2M) Digital Trunk Interface. DOWNWhen connected to T1 (1.5M) Digi- tal Trunk Interface.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2ODTA (ODT) NEAX2000 IVS2 Installation Procedure ManualPage 378ND-70928 (E), Issue 1.0 PN-2ODTA (ODT) Locations of Lamps, Switches, and Connectors Lamp Indications Switch Settings This card has no switches. LAMP NAMECOLOR FUNCTION BL0, 1 RedRemains lit when the corresponding circuit is in use. Flashes at 60 IPM when the corresponding circuit is in make- busy state or the system data for this card is not assigned. BL1 BL0 CN1
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2ODTB (ODT) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 379 PN-2ODTB (ODT) Locations of Lamps, Switches, and Connectors Lamp Indications Switch Settings This card has no switches. LAMP NAMECOLOR FUNCTION BL0, 1 RedRemains lit when the corresponding circuit is in use. Flashes at 60 IPM when the corresponding circuit is in make- busy state or the system data for this card is not assigned. BL1 BL0 CN1
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-8RSTA (PBR) NEAX2000 IVS2 Installation Procedure ManualPage 380ND-70928 (E), Issue 1.0 PN-8RSTA (PBR) Locations of Lamps, Switches, and Connectors Lamp Indications This card has no lamps. Switch Settings This card has no switches.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-TNTA (TNT) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 381 PN-TNTA (TNT) Locations of Lamps, Switches, and Connectors Lamp Indications This card has no lamps. JAC K1 JAC K0 SW
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-TNTA (TNT) NEAX2000 IVS2 Installation Procedure ManualPage 382ND-70928 (E), Issue 1.0 Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW (Piano Key SW) 1, 2Volume adjustment for No.0 circuit 3, 4Volume adjustment for No.1 circuit 4 3 2 1 OFF ON SWITCH NUMBER VO L U M E 12 OFF OFF–10dB ON OFF–7dB OFF ON–4dB ON ON–1dB SWITCH NUMBER VO L U M E 34 OFF OFF–10dB ON OFF–7dB OFF ON–4dB ON ON–1dB
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-4VCTH (VCT) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 383 PN-4VCTH (VCT) Locations of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION BL0-3 RedRemains lit when the corresponding circuit is in use. Flashes at 60 IPM when the corresponding circuit is in make- busy state or the system data for this card is not assigned. SW1 BL3 BL2 BL1 BL0 IPT EXPFROM PN-IPTA CONNECTOR OR FROM OTHER PN-4VCTH CARD CONNECTOR TO IPT CONNECTOR OF OTHER PN-4VCTH CARD
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-4VCTH (VCT) NEAX2000 IVS2 Installation Procedure ManualPage 384ND-70928 (E), Issue 1.0 Switch Settings The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW1 (Piano Key SW) 1, 2Set the number per VCT card if two or more VCT cards are used. (Max. four VCT cards) 3ON Not used OFF 4ON Not used OFF 4 3 2 1 OFF ON SW No. Card No. 12 OFF OFF 0 ON OFF 1 OFF ON 2 ON ON 3