NEC Neax 2000 Ivs2 Installation Procedure Manual

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-8COTQ (COT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 335
PN-8COTQ (COT)
Locations of Lamps, Switches, and Connectors 
Lamp Indications
Switch Settings
This card has no switches.
LAMP 
NAMECOLOR FUNCTION
BL0-7 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
BL7
BL6
BL5
BL4
BL3
BL2
BL1
BL0 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-8COTR (COT)
NEAX2000 IVS2 Installation Procedure ManualPage 336ND-70928 (E), Issue 1.0
PN-8COTR (COT)
Locations of Lamps, Switches, and Connectors 
Lamp Indications
Switch Settings
This card has no switches.
LAMP 
NAMECOLOR FUNCTION
BL0-7 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
BL7
BL6
BL5
BL4
BL3
BL2
BL1
BL0 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-8COTS (COT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 337
PN-8COTS (COT)
Locations of Lamps, Switches, and Connectors 
Lamp Indications
Switch Settings
This card has no switches.
LAMP 
NAMECOLOR FUNCTION
BL0-7 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
BL7
BL6
BL5
BL4
BL3
BL2
BL1
BL0 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-8COTT (COT)
NEAX2000 IVS2 Installation Procedure ManualPage 338ND-70928 (E), Issue 1.0
PN-8COTT (COT)
Locations of Lamps, Switches, and Connectors 
Lamp Indications
Switch Settings
This card has no switches.
LAMP 
NAMECOLOR FUNCTION
BL0-7 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
LF0-7 RedRemains lit when the corresponding circuit detects a line fault 
condition.
BL7
BL6
BL5
BL4
BL3
BL2
BL1
BL0
LF7
LF6
LF5
LF4
LF3
LF2
LF1
LF0 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2CSIA (CSI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 339
PN-2CSIA (CSI)
Locations of Lamps, Swtiches, and Connectors
OPE
B13 LB
B12
B11
B10
B02 B03
B01
B00
DL1
DL0 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2CSIA (CSI)
NEAX2000 IVS2 Installation Procedure ManualPage 340ND-70928 (E), Issue 1.0
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
OPE Green Remains lit when the corresponding circuit is in use.
LB Red Remains lit when a loop-back is in progress.
B13 Red Not used (Flash [60 IPM])
B12 Red B channel status
ON  :  B2 channel of the No. 1 circuit is in use.
OFF :  B2 channel of the No. 1 circuit is idle.
Flash (60 IPM) :  ZT is not connected to the No. 1 circuit.
ZT is in make-busy status.
B11 Red B channel status
ON  :  B1 channel of the No. 1 circuit is in use.
OFF :  B1 channel of the No. 1 circuit is idle.
Flash (60 IPM) :  ZT is not connected to the No. 1 circuit.
ZT is in make-busy status.
B10 Red B channel status
ON  :  B0 channel of the No. 1 circuit is in use.
OFF  :  B0 channel of the No. 1 circuit is idle.
Flash (60 IPM) :  ZT is not connected to the No. 1 circuit.
ZT is in make-busy status.
B03 Red Not used (Flash [60 IPM])
B02 Red B channel status
ON  :  B2 channel of the No. 0 circuit is in use.
OFF  :  B2 channel of the No. 0 circuit is idle.
Flash (60 IPM) :  ZT is not connected to the No. 0 circuit.
ZT is in make-busy status.
B01 Red B channel status
ON  :  B1 channel of the No. 0 circuit is in use.
OFF  :  B1 channel of the No. 0 circuit is idle.
Flash (60 IPM) :  ZT is not connected to the No. 0 circuit.
ZT is in make-busy status.
(Continued) 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2CSIA (CSI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 341
Switch Settings
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION 
column indicate the standard setting of the switch. When the switch is not set as shown by the 
figure and   , the setting of the switch varies with the system concerned.
NOTE:
Set the groove on the switch to the desired position. B00 Red B channel status
ON  :  B0 channel of the No. 0 circuit is in use.
OFF  :  B0 channel of the No. 0 circuit is idle.
Flash (60 IPM) :  ZT is not connected to the No. 0 circuit.
ZT is in make-busy status.
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
DL0
(Rotary SW)
NOTE0-FFor normal operation
1-F Not used
DL1
(Rotary SW)
NOTE0-FFor normal operation
1-F Not used
LAMP 
NAMECOLOR FUNCTION
0
0
0
0 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2CSIA-A (CSI)
NEAX2000 IVS2 Installation Procedure ManualPage 342ND-70928 (E), Issue 1.0
PN-2CSIA-A (CSI)
Locations of Lamps, Swtiches, and Connectors
OPE
B13 LB
B12
B11
B10
B02 B03
B01
B00
DL1
DL0
SP 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2CSIA-A (CSI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 343
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
OPE Green Remains lit when the corresponding circuit is in use.
LB Red Remains lit when a loop-back is in progress.
B13 Red Not used (Flash [60 IPM])
B12 Red B channel status
ON  :  B2 channel of the No. 1 circuit is in use.
OFF :  B2 channel of the No. 1 circuit is idle.
Flash (60 IPM) :  CS is not connected to the No. 1 circuit.
CS is in make-busy status.
B11 Red B channel status
ON  :  B1 channel of the No. 1 circuit is in use.
OFF :  B1 channel of the No. 1 circuit is idle.
Flash (60 IPM) :  CS is not connected to the No. 1 circuit.
CS is in make-busy status.
B10 Red B channel status
ON  :  B0 channel of the No. 1 circuit is in use.
OFF  :  B0 channel of the No. 1 circuit is idle.
Flash (60 IPM) :  CS is not connected to the No. 1 circuit.
CS is in make-busy status.
B03 Red Not used (Flash [60 IPM])
B02 Red B channel status
ON  :  B2 channel of the No. 0 circuit is in use.
OFF  :  B2 channel of the No. 0 circuit is idle.
Flash (60 IPM) :  CS is not connected to the No. 0 circuit.
CS is in make-busy status.
B01 Red B channel status
ON  :  B1 channel of the No. 0 circuit is in use.
OFF  :  B1 channel of the No. 0 circuit is idle.
Flash (60 IPM) :  CS is not connected to the No. 0 circuit.
CS is in make-busy status.
(Continued) 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2CSIA-A (CSI)
NEAX2000 IVS2 Installation Procedure ManualPage 344ND-70928 (E), Issue 1.0
Switch Settings
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION 
column indicate the standard setting of the switch. When the switch is not set as shown by the 
figure and   , the setting of the switch varies with the system concerned.
NOTE:
Set the groove on the switch to the desired position. B00 Red B channel status
ON  :  B0 channel of the No. 0 circuit is in use.
OFF  :  B0 channel of the No. 0 circuit is idle.
Flash (60 IPM) :  CS is not connected to the No. 0 circuit.
CS is in make-busy status.
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
DL0
(Rotary SW)
NOTE0-FFor normal operation
1-F Not used
DL1
(Rotary SW)
NOTE0-FFor normal operation
1-F Not used
SP (jumper SW)
For normal operation
DOWN Not used
LAMP 
NAMECOLOR FUNCTION
0
0
0
0
Front 1
2
3
UP