NEC Neax 2000 Ivs2 Installation Procedure Manual
Have a look at the manual NEC Neax 2000 Ivs2 Installation Procedure Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-8DLCP (DLC) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 355 PN-8DLCP (DLC) Locations of Lamps, Switches, and Connectors Lamp Indications Switch Settings This card has no switches. LAMP NAMECOLOR FUNCTION BL0-7 RedRemains lit when the corresponding circuit is in use. Flashes at 60 IPM when the corresponding circuit is in make- busy state or the system data for this card is not assigned. BL7 BL6 BL5 BL4 BL3 BL2 BL1 BL0
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2DPCB (DPC) NEAX2000 IVS2 Installation Procedure ManualPage 356ND-70928 (E), Issue 1.0 PN-2DPCB (DPC) Location of Lamps, Switches, and Connectors SW0 XCN1 XCN0 RS1 RS0BL1 LB11 LB12 RSC1 SDT1 RDR1 CDI1 RSC0 SDT0 RDR0 CDI0BL0 LB01 LB02 SW1 To X.21 DTE/DCE or PN-M03 To V.24/V.28 DTE/DCE
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2DPCB (DPC) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 357 Lamp Indications LAMP NAMECOLOR FUNCTION BL0 Red No. 0 CircuitON: Ready for digital data transmission or the cir- cuit is busy. OFF: Fixed path is not connected. Flash (60 IPM): Make-busy state or the system data for this card is not assigned. Flash (120 IPM): Fixed path is connected. LB01 Red ON: Loop Back 1 is set. OFF: Normally operating. LB02 Red ON: Loop Back 2 is set. OFF: Normally operating. RSC0 Green ON: RTS/C signal ON OFF: RTS/C signal OFF SDT0 Green ON: TXD/T signal is “0”. OFF: TXD/T signal is “1”. RDR0 Green ON: RXD/R signal is “0”. OFF: RXD/R signal is “1”. CDI0 Green ON: DCD/I signal ON OFF: DCD/I signal OFF (Continued)
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2DPCB (DPC) NEAX2000 IVS2 Installation Procedure ManualPage 358ND-70928 (E), Issue 1.0 Switch SettingsBL1 Red No. 1 CircuitON: Ready for digital data transmission or the cir- cuit is busy. OFF: Fixed path is not connected. Flash (60 IPM): Make-busy state or the system data for this card is not assigned. Flash (120 IPM): Fixed path is connected. LB11 Red ON: Loop Back 1 is set. OFF: Normally operating. LB12 Red ON: Loop Back 2 is set. OFF: Normally operating. RSC1 Green ON: RTS/C signal ON OFF: RTS/C signal OFF SDT1 Green ON: TXD/T signal is “0”. OFF: TXD/T signal is “1”. RDR1 Green ON: RXD/R signal is “0”. OFF: RXD/R signal is “1”. CDI1 Green ON: DCD/I signal ON OFF: DCD/I signal OFF SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW1 (Piano Key SW)1ON No. 0 CircuitLoop Back 1 ON Loop Back 1 OFF 2ON Loop Back 2 ON Loop Back 2 OFF 3ON No. 1 CircuitLoop Back 1 ON Loop Back 1 OFF 4ON Loop Back 2 ON Loop Back 2 OFF (Continued) LAMP NAMECOLOR FUNCTION 4 3 2 1 OFF ON OFF OFF OFF OFF
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2DPCB (DPC) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 359 The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE: When the power is on, disconnect the cables before unplugging the circuit card and connect the cables after plugging the circuit card. SW0 (DIP SW) 1ONNo. 0 CircuitForcibly turning the DTR signal to ON OFFThe DTR signal from DTE goes through the card 2ONForcibly turning the RTS/C signal to ON OFFThe RTS/C signal from DTE goes through the card 3 Not used 4ON V.11 (X.21) interface OFFV.24/V.28 (RS-232C) interface 5ONNo. 1 CircuitForcibly turning the DTR signal to ON OFFThe DTR signal from DTE goes through the card 6ONForcibly turning the RTS/C signal to ON OFFThe RTS/C signal from DTE goes through the card 7 Not used 8ON V.11 (X.21) interface OFFV.24/V.28 (RS-232C) interface SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK 1 23 45 67 8ON OFF OFF
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2ILCA (ILC) NEAX2000 IVS2 Installation Procedure ManualPage 360ND-70928 (E), Issue 1.0 PN-2ILCA (ILC) Locations of Lamps, Switches, and Connectors PA L 1AC T1 LPB1 B21 B11 PA L 0 AC T0 LPB0 B20 B10 SW1 SW0
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2ILCA (ILC) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 361 Lamp Indications LAMP NAMECOLOR FUNCTION ACT1 Green No.1 CircuitON: Normally operating. OFF: Not operating. PAL1 Red ON: Line is short-circuiting. OFF: Normally operating. LPB1 Red OFF: Not used. B21 Green ON: B2 channel is in use. OFF: B2 channel is idle. B11 Green ON: B1 channel is in use. OFF: B1 channel is idle. ACT0 Green No. 0 CircuitON: Normally operating. OFF: Not operating. PAL0 Red ON: Line is short-circuiting. OFF: Normally operating. LPB0 Red OFF: Not used B20 Green ON: B2 channel is in use. OFF: B2 channel is idle. B10 Green ON: B1 channel is in use. OFF: B1 channel is idle.
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-2ILCA (ILC) NEAX2000 IVS2 Installation Procedure ManualPage 362ND-70928 (E), Issue 1.0 Switch Settings The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW1 (Piano Key SW)1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4 Always set to OFF SW0 (Piano Key SW) 1No.0 Circuit (Receiving)Terminating register is provided. OFFTerminating register is not provided. 2No.0 Circuit (Sending)Terminating register is provided. OFFTerminating register is not provided. 3No.1 Circuit (Receiving)Terminating register is provided. OFFTerminating register is not provided. 4No.1 Circuit (Sending)Terminating register is provided. OFFTerminating register is not provided. 4 3 2 1 OFF ON OFF OFF OFF OFF 4 3 2 1 OFF ON ON ON ON ON
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-4LCC (LC) NEAX2000 IVS2 Installation Procedure Manual ND-70928 (E), Issue 1.0Page 363 PN-4LCC (LC) Locations of Lamps, Switches, and Connectors Lamp Indications Switch Settings This card has no switches. LAMP NAMECOLOR FUNCTION BL0-3 RedRemains lit when the corresponding circuit is in use. Flashes at 60 IPM when the corresponding circuit is in make- busy state or the system data for this card is not assigned. BL3 BL2 BL1 BL0
CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS PN-4LCD-A (LC) NEAX2000 IVS2 Installation Procedure ManualPage 364ND-70928 (E), Issue 1.0 PN-4LCD-A (LC) Locations of Lamps, Switches, and Connectors Lamp Indications Switch Settings This card has no switches. LAMP NAMECOLOR FUNCTION BL0-3 RedRemains lit when the corresponding circuit is in use. Flashes at 60 IPM when the corresponding circuit is in make- busy state or the system data for this card is not assigned. BL3 BL2 BL1 BL0