NEC Neax 2000 Ivs2 Installation Procedure Manual

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2BRTC (BRT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 245
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-31) to
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW0, SW10
(DIP SW)
1For terminating the transmitting side 
of channels B1 and B2 with 100 
ohms.
OFFTo remove the terminating resistor 
on the transmitting side of channels 
B1 and B2.
2For terminating the receiving side of 
channels B1 and B2 with 100 ohms.
OFFTo remove the terminating resistor 
on the receiving side of channels B1 
and B2.
(Continued)
F
4AP No.SW11-4: ON
04 05 06 07 08 09 10 11 12 13 14 15
SW11-4: OFF
20 21 22 23 24 25 26 27 28 29 30 31
SW No.
456789ABCDEF
ON
DOWN
1
2ON
ON
ON 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2BRTC (BRT)
NEAX2000 IVS2 Installation Procedure ManualPage 246ND-70928 (E), Issue 1.0
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card. SW11 (DIP SW)
1For normal operation
OFF Not used
2
NOTE 3
NOTE 4ONOutput clock signals according to
the switch setting of SW11-3.
OFF Do not output clock signals.
3
NOTE 3
NOTE 4ON Output clock signals to PLO 0 of MP.
OFF Output clock signals to PLO 1 of MP.
4ON AP No. 04-15
OFF AP No. 20-31
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
4ON
ON 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2BRTC (BRT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 247
NOTE 3:
The system can supply clock signals from two clock supply routes.
In normal condition, the system synchronizes to the clock signals supplied on the PLO
0 of MP card via the Back Wiring Board, and if the clock signals are failed, the clock
supply route takes over to PLO1 automatically. Set SW11-2 and SW11-3 as follows.
NOTE 4:
When the system is a clock source office, set the SW11-2 and SW11-3 on all the BRT
cards mounted in PIM0 to “OFF”.
NOTE 5:
Mount the BRT card which receives a source clock signals into PIM0. CONDITIONSBRT0 BRT1 BRT2 ---- BRT11
REMARKS
SW
11-2SW
11-3SW
11-2SW
11-3SW
11-2SW
11-3----SW
11-2SW
11-3
When one BRT 
is provided.ON ONMP card will receive the clock 
signal from No.0 circuit of 
BRT0 at its PLO0 input.
Should a clock failure occure 
with No.0 circuit, MP card will 
switch to No. 1 circuit of 
BRT0.
When more 
than one BRT 
is provided.ON ON ON OFF OFF ON ---- OFF ONMP card will receive the clock 
signal from BRT0 at its PLO0 
input, under normal condi-
tions.
Should a clock failure occure 
with both No.0 and No.1 cir-
cuits of BRT0, MP card will 
switch to the PLO1 input 
which gets clock from BRT1. 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-CC01 (ETHER)
NEAX2000 IVS2 Installation Procedure ManualPage 248ND-70928 (E), Issue 1.0
PN-CC01 (ETHER)
Location of Lamps, Switches, and Connectors
RUN
MB
LINK 
XMT 
RCV 
RV P  
ERR
IP 10BASE-T
SW1SW2 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-CC01 (ETHER)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 249
Lamp Indications
Switch Settings
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 60 IPM while this card is operating normally.
LINK Green Remains lit when link is established.
XMT Green Remains lit when it is transmitting the data.
RCV Green Remains lit when it is receiving the data.
RVP Green Remains lit only when it is receiving the data with its own IP
address.
ERR–Not used
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
MB (Toggle SW)
NOTE 1UP For make-busy
For normal operation
(Continued)
ON
DOWN 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-CC01 (ETHER)
NEAX2000 IVS2 Installation Procedure ManualPage 250ND-70928 (E), Issue 1.0
SW1 (DIP SW)
NOTE 2
SW1-5 (D11)
SW1-6 (D10)
SW1-7 (D9)
SW1-8 (D8)
1 (D15) ON
2 (D14) ON
3 (D13) ON
4 (D12) OFF
5 (D11)ON
OFF
6 (D10)ON
OFF
7 (D9)ON
OFF
8 (D8)ON
OFF
SW2 (DIP SW)
NOTE 21 (D7)ON
OFF
2 (D6)ON
OFF
3 (D5)ON
OFF
4 (D4)ON
OFF
5 (D3)ON
OFF
6 (D2)ON
OFF
7 (D1)ON
OFF
8 (D0)ON
OFF
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
1
23
45
67
8ON
MAC ADDRESS SWITCH SETTING
00004CA4 X X X X 
(HEX)
    FixedSW2-5 (D3)
SW2-6 (D2)
SW2-7 (D1)
SW2-8 (D0)ON/OFF
ON/OFF
ON/OFF
ON/OFF
SW2-1 (D7)
SW2-2 (D6)
SW2-3 (D5)
SW2-4 (D4)ON/OFF
ON/OFF
ON/OFF
ON/OFF
SW1-5 (D11)
SW1-6 (D10)
SW1-7 (D9)
SW1-8 (D8)ON/OFF
ON/OFF
ON/OFF
ON/OFF
SW1-1 (D15)
SW1-2 (D14)
SW1-3 (D13)
SW1-4 (D12)ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON:0  OFF:1
1
23
45
67
8ON 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-CC01 (ETHER)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 251
NOTE 1:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card.
NOTE 2:
Each equipment must have a unique MAC address to distinguish between systems.
Therefore, when more than one PBX is installed in the same network, assign the lower
4 digits of the following MAC address by SW1 and SW2 to prevent duplicate address-
es. 
00004CA4 XX XX (HEX)
According to the switch setting of SW2 (D7-D0)
According to the switch setting of SW1 (D15-D8)
Fixed 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIA (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 252ND-70928 (E), Issue 1.0
PN-DAIA (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Remains lit when a link between this card and a distant office is 
normally connected.
Goes out after 15 seconds of link disconnection.
RED Red Remains lit when detecting PCM signal loss or Frame Alignment 
signal loss.
RMT Red Remains lit when receiving the alarm signal from a distant office.
LOOP–Not used
PWR–Not used
BL Red Remains lit while data transmission on control channel (D ch).
Flashes while FP data downloading. 
JPS
JPR
SW2
SW3BUS
PCM1
PCM0
CNSENSE
RUN
MB
SW1LINK 
RED 
RMT 
LOOP 
PWR 
BL 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIA (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 253
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 10-FFP (Firmware Processor) Number setting for the
DAIA card.
By this setting, the system regards the DAIA card
and the opposite DAIB card as one Firmware Pro-
cessor.
0 Not used
1FP No. 1
2FP No. 2
3FP No. 3
4 – F Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW1
(Piano Key SW)1
NOTE 3ONFor supplying 1.5MHz clock to 
PLO 0
No clock supply to PLO 0
2
NOTE 3ONFor supplying 1.5MHz clock to 
PLO 1
No clock supply to PLO 1
3 Always set to OFF
4 Always set to OFF
(Continued)
1
32
ON
DOWN
4 
3 
2 
1 OFF
ON
OFF
OFF
OFF
OFF 
						

							CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIA (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 254ND-70928 (E), Issue 1.0
SW2 (DIP SW)
1ONControl channel signaling data 
transmission speed: 48kbps
Control channel signaling data 
transmission speed: 64kbps
2ONDTI frame configuration: 12-Multi 
Fram e
DTI frame configuration: 24-Multi 
Fram e
3ON Line code: AMI with ZCS
Line code: B8ZS
4ONSetting of control signal time slot
NOTE 4, NOTE 5 5ON
6ON
7
OFF
8ON
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
45
67
8ONOFF
OFF
OFF
SWITCH NUMBER
TIME SLOT
NUMBER
45678
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFFON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFFON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFFON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ONON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFFTS1
TS2
TS3
TS4
TS5
TS6
TS7
TS8
TS9
TS10
TS11
TS12
TS13
TS14
TS15
TS16
TS17
TS18
TS19
TS23
OFF
OFF
OFF
ON
OFF