Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-11 Call Detail Recording Option Settings 
A
Call Detail Recording Option Settings
The interfac e between the system and  Call Detail Rec ord ing  (CDR) equip ment 
may b e one of the following :
nData Module — Rec ommend ed  op tion setting s are shown in Ta b l e  A - 3.
nMod em — Rec ommend ed  option setting s are in mod em vend or 
document
nTN726 Data Line c irc uit p ac k and  an Async hronous Data Unit — Data 
mod ules or mod ems are not req uired .
nConnec ted  d irec tly to the DCE
 connector (Electronic Industries 
Assoc iation (EIA) Port) loc ated  on the rear of the Control Carrier 
— data 
mod ules or mod ems are not req uired .
A 572 Printer c an be used  as an outp ut rec eiving  d evic e for Call Detail Rec ord ing  
(CDR). The rec ommend ed  option setting s for this p rinter are shown in the 
f o l lo w in g  t a b le s.  Al so ,  a  TEL ESEER,  C a ll  D e t a il  Re c o rd in g  ( C D R) ,  9 4 A L o c a l 
Storag e Unit (LSU), or Customer Premises Eq uip ment (CPE) c an b e used  as the 
output receiving  d evice.
Ad ministration p roc ed ures for Call Detail Rec ord ing  (CDR) eq uip ment are 
p rovid ed in 
DEFINITY Enterp rise Communic ations Server Release 8 
Ad ministration and  Feature Desc ription
.
AUDIX Interface Option Settings
The Aud io Information Exc hang e (AUDIX) is sometimes c onnec ted  to the system 
throug h the TN765 Proc essor Interfac e c irc uit p ac k. The first c irc uit on the 
p roc essor interfac e c an b e c onnec ted  d irec tly to the AUDIX throug h the PI
 
c onnec tor on the rear of the c ontrol c arrier.
Any of the remaining  three c irc uits on the p roc essor interfac e to b e used  to 
sup p ort AUDIX must b e c onnec ted  throug h a 7400D Data Mod ule serving  as the 
interfac e link for AUDIX. The option setting s are shown in Ta b l e  A - 6
.
Table A-6. Data Module Settings for DEFINITY AUDIX
DIP Switch 1 Setting
9600 ON
SYN C O N
INT ON
AANS ON
All Other Switc hes OFF 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-12 TN760D Tie Trunk Circuit Pack Option Settings 
A
TN760D Tie Trunk Circuit Pack Option 
Settings
The TN760D Tie Trunk c irc uit p ac k interfac es b etween the tie trunks and  the Time 
Division Multip lex (TDM) b us. Two tip  and ring  p airs form a 4-wire analog  
transmission line. An E and M pair is used for signaling and are DC signaling 
lead s used  for c all setup . The E lead  rec eives sig nals from the tie trunk and the M 
lead  transmits sig nals to the tie trunk. 
To c hoose the preferred  sig naling  format (Ta b l e  A - 7
 and Ta b l e  A - 8), set the 
switc hes on the TN760D and  ad minister the p ort per Fi g u re  A - 3
 and  Ta b l e  A - 9.
!CAUTION:
To p revent d amag e from static  elec tric ity, wear an EMC wrist strap  
(c omc od e 900698226) when hand ling  c irc uit p ac ks or other c omp onents.
Table A-7. Signaling Formats for TN760D
Mode Type
E & M Typ e I Stand ard  (unp rotec ted )
E & M Typ e I Comp atib le (unp rotec ted )
Protected Type I Compatible, Type I Standard
Sim p l e x Typ e  V
E & M Typ e  V
E & M Typ e V Revised
Table A-8. Signaling Type Summary
Signaling Transmit (M-Lead) Receive (E-Lead)
Type On-Hook Off-Hook On-Hook Off-Hook
Type I Standard grd bat open
1/b at
1. An op en c irc uit is p referred  instead  of b attery voltag e.grd
Type I Compatible open
1/b at g rd g rd op en1/b at
Type V open
1/bat grd open grd
Type V Reversed grd open grd open 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-13 TN760D Tie Trunk Circuit Pack Option Settings 
A
Figure A-3. TN760D Tie Trunk Circuit Pack (Component Side)
4321
PORT 4 PORT 3 PORT 2PORT 1 UNPROT
PROTSMPLX
E&MSMPLX
E&MSMPLX
E&MSMPLX
E&M
r758183RBP050896 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-14 TN760D Tie Trunk Circuit Pack Option Settings 
A
Table A-9. TN760D Option Switch Settings and Administration
Installation
SituationSet
Prot/
Unprot
Option
Switch Preferred
Signaling FormatSet 
E&M/SMPLX
Option
SwitchAdministered
Port Circumstance To System Far-End
Co-Loc ated Sys75/G1 Simp lex Simp lex SMPLX Either Typ e 5
Typ e 5 Typ e 5
Inter-Build ing Sys75/G1 Simp lex Simp lex SMPLX Either Typ e 5
Typ e 5 Typ e 5
Co-Loc ated Sys85/G2 Simp lex Simp lex SMPLX Either Typ e 5
Typ e 5 Typ e 5
Inter-Build ing Sys85/G2 Simp lex Simp lex SMPLX Either Typ e 5
Typ e 5 Typ e 5
Co-Loc ated DIMENSION E&M Typ e 1 E&M Typ e 1 E&M Unp rotec ted Typ e 1
PBX Comp atible Stand ard Compatible
Inter-Build ing DIMENSION Protec ted  
Ty p e  1Protec ted 
Typ e 1E&M Pro te c t e d Typ e  1
PBX Comp atible Stand ard Compatible
Co-Loc ated Other E&M Typ e 1 E&M Typ e 1 E&M Unp rotec ted Typ e 1
Comp atible Stand ard Compatible
Inter-Build ing Other Protec ted  
Ty p e  1Protec ted 
Typ e 1E&M Pro te c t e d Typ e  1
Comp atible Stand ard 
Pl u sCompatible
Protec tion
Unit
Co-Loc ated Net 
Integ ratedE&M Typ e 1 Any PBX E&M Unp rotec ted Typ e 1
Stand ard 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-15 TN464/2464 Option Settings 
A
TN464/2464 Option Settings
The TN464/2464 DS1/E1 Interfac e-T1/E1 c irc uit p ac k interfac es b etween a 24 or 
32 c hannel CO/ISDN or tie trunk and  the Time Division Multip lexing  (TDM) b us.
Set the switc hes on the c irc uit p ac k to selec t b it rate and imp edanc e matc h. See 
Ta b l e  A - 1 0
 and  Fi g u re  A - 4.
Figure A-4. TN464/2464 Option Settings
Table A-10. Option Switch Settings on TN464/2464
120 Ohms Twisted pair
75 Ohms Coaxial req uiring  888A ad ap ter
32 Channel 2.048 Mb p s
24 Channel 1.544 Mb p s
3
8
4
9
5
10
1
6
2
7
1. Bac kp lane Connec tors
2. 24/32 Channel Selec tor
3. 75/120 ohm Selec tor
4. Fac ep late
5. 32 Channel6. 120 ohm (shown selec ted )
7. 24 Channel (shown selec ted )
8. 75 ohm
9. Connec tor
10. TN464/2464
Figure Notes: 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-16 TN464/2464 Option Settings 
A 
						

							Connecting and Handling Fiber Optic Cables 
B-1 LASER Product 
B
DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
B
Connecting and Handling Fiber 
Optic Cables
Sig nals b etween the c ab inets c omp osing  the system are c arried  by fib er op tic  
c ab les. To ac c omp lish this, the elec tronic  signals at the c onnec tors on the b ac k 
of a c ab inet must b e c onverted  into op tic al sig nals and op tic al sig nals from 
another c ab inet must b e c onverted  b ac k into elec tronic  sig nals. Op to-elec tronic  
d evic es (lig htwave transc eivers) p rovid e this interfac e.
LASER Product
The DEFINITY ECS may c ontain a Class 1 LASER devic e if sing le-mod e fib er 
op tic  c ab le is c onnec ted  to a remote Exp ansion Port Network (EPN). The LASER 
d evic e op erates within the following  p arameters:
nPower Output: -5 d Bm
nWaveleng th: 1310 nm
nMod e Field  Diameter: 8.8 µm
nCLASS 1 LASER PRODUCT
nIEC 825 1993
!CAUTION:
Use of c ontrols or ad justments or p erformanc e of p roc ed ures other 
than those specified herein may result in hazardous radiation 
exp osure.
Contac t your Luc ent Tec hnolog ies rep resentative for more information. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Connecting and Handling Fiber Optic Cables 
B-2 Optical Cross-Connect Hardware 
B
Optical Cross-Connect Hardware
Optic al c ross-c onnec ts c onsist of Lightg uide Interc onnec t Units (LIUs) with 
lig htg uid e troug hs in b etween them. Fi g u re  B - 1
 shows a typ ic al LIU. One LIU 
terminates the inc oming  c ab les and the other terminates the outg oing  c ab les. A 
fib er op tic  p atc h c ord  or jump er is used  to c onnec t the c irc uits. Circ uits c an b e 
rerouted  the same as on 110-typ e c onnec ting  b loc ks, by moving  the p atc h c ord  
from one p oint on the Main Distrib ution Frame (MDF) to another.
Figure B-1. Typical Optical Lightguide Interconnect Unit
1. 100A Lig htguide Interc onnect Unit 
(LIU)
2. Multi-Mod e Connec tor (C2000A-2)
Sing le-Mod e Connec tor (C3000A-2)
3. Ad hesive-Bac ked  Circuit Labels4. 1A4 Lig htg uid e Troug h
5. Fib er Patc h Cord
6. 1A6 Lig htg uid e Troug h
7.Op en Lig htg uid e Interc onnec t Unit 
(LIU) 
Figure Notes: 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Connecting and Handling Fiber Optic Cables 
B-3 Optical Cross-Connect Hardware 
B
Optic al interc onnec ts c onsist of Lig htg uid e Interc onnec t Units (LIUs) without a 
troug h b etween them. Fi g u re  B - 2
 shows a typ ic al Interc onnec t field. Inc oming  
and  outg oing  multi-mod e and  sing le-mode c ab les are c onnec ted  d irec tly to eac h 
other. This arrang ement makes c irc uit c hang es more d iffic ult, b ut red uc es op tic al 
losses.
Figure B-2. Typical Optical Interconnect Field
Optic al c ross-c onnec t and  interc onnec t field s are made up  of the following:
n100A Lig htguid e Interc onnec t Unit (LIU)
n10A Lig htg uid e Connec tor Panel
nC2000A-2 Connec tor Coup ling  (Multi-Mod e) or C3000A-2 Connec tor 
Coupling (Single-Mode)
n1A4 Lig htg uid e Troug h
n1A6 Lig htg uid e Troug h
nMulti-Mod e or Sing le-Mod e Fiber Interc onnec t Cab le
1. 100A Lig htg uid e Interc onnec t Unit 
(LIU)
2. Op en Lig htg uid e Interc onnec t Unit 
(LIU) Door3. C2000A-2 Connec tor (Multi-Mod e)
C3000A-2 Connec tor 
(Single-Mode)
4. Labels
Figure Notes: 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Connecting and Handling Fiber Optic Cables 
B-4 Optical Cross-Connect Hardware 
B
100A Lightguide Interconnect Unit
The 100A Lig htg uid e Interc onnec t Unit (LIU) (c omc od e 104141841) c onsists of a 
c ab inet with retainer ring s to hold  slac k fib er c ab les, mounting  c utouts for two 
10A lightg uid e c onnec tor p anels, and a d oor with c irc uit lab els on eac h sid e. See 
Fi g u re  B - 3
.
Figure B-3. 100A Lightguide Interconnection Unit
1. 100A Lig htg uid e Interc onnec t 
Unit (LIU)2. Retainer Ring s
3. Circ uit Lab els
Figure Notes: