Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Test the System 
4-5 Test Time Division Multiplexing Bus in Processor Port Network 
4
Test Time Division Multiplexing Bus
in Processor Port Network
1. Verify the sc reen d isp lays command:
2. Type test tdm port-network 1 
and  p ress 
En t e r.
3. Verify the sc reen d isp lays the results of this test. See Sc reen 4-4
.
Screen 4-4. Sample Test Results for TDM Bus Port Network 1
4. If 
the result is FAIL
 for any test, c hec k the c onnec tors of the TDM b us 
c ab les in Proc essor Port Network (PPN) 1.
test tdm port-network 1 
                                  TEST RESULTS
   Port      Maintenance Name  Alt. Name Test No. Result            Error Code
   PN 01A    TDM-BUS                     294      PASS
   PN 01A    TDM-BUS                     296      PASS
   PN 01A    TDM-BUS                     297      ABORT             1005
   PN 01B    TDM-BUS                     294      PASS
   PN 01B    TDM-BUS                     296      ABORT             1005
   PN 01B    TDM-BUS                     297      PASS
 Command successfully completed
 Command: 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Test the System 
4-6 Test Tone-Clock Boards 
4
Test Tone-Clock Boards
Testing the Tone-Clock board also detects problems with the TDM bus cables.
1. Verify the sc reen d isp lays command:
2. Type test tone-clock 1a 
and  p ress 
En t e r.
3. Verify pag e 1 disp lays the test results similar to Sc reen 4-5
.
  
Screen 4-5. Sample Test Results for Tone-Clock 1A
test tone-clock 1a 
                                  TEST RESULTS
   Port      Maintenance Name  Alt. Name Test No. Result            Error Code
   01A       TONE-BD                     46       PASS
   01A       TONE-BD                     52       PASS
   01AXX01   ETR-PT                      42       PASS
   01AXX01   ETR-PT                      43       PASS
   01AXX02   ETR-PT                      42       PASS
   01AXX02   ETR-PT                      43       PASS
   01AXX03   ETR-PT                      42       PASS
   01AXX03   ETR-PT                      43       PASS
   01AXX04   ETR-PT                      42       PASS
   01AXX04   ETR-PT                      43       PASS
   01AXX05   ETR-PT                      42       PASS
   01AXX05   ETR-PT                      43       PASS
   01AXX06   ETR-PT                      42       PASS
   01AXX06   ETR-PT                      43       PASS
Command successfully completed
Command: 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Test the System 
4-7 Test Expansion Interface Circuit Packs 
4
Test Expansion Interface Circuit Packs
Chec k eac h Expansion Interfac e (EI) c irc uit pac k in the system.
1. Verify the sc reen d isp lays command:
2. Type test board xxx
 where xxx 
is the c ab inet, c arrier, and  slot for an 
Exp ansion Interfac e (EI) c irc uit p ac k in the system, and  p ress 
En te r.
NOTE:
Lab els on the p ort network and  c arrier and on the strip  und er the 
c irc uit pac k c ontain this information.
3. Verify the sc reen d isp lays test results similar to Sc re e n  4 - 6
. This examp le 
is for b oard  2a01.
Screen 4-6. Sample Test Results for Expansion Interface Board 2A01
4. If any result is FAIL, c hec k the c onnec tions for the fib er optic  link.
5. Rep eat Step s 2 and 3 for eac h Exp ansion Interfac e c irc uit p ac k.
                                TEST RESULTS
  Port      Maintenance Name  Alt. Name Test No. Result            Error Code
  02A01     EXP-INTF                    237      PASS
  02A01     EXP-INTF                    238      PASS
  02A01     EXP-INTF                    240      PASS
  02A01     EXP-INTF                    241      PASS
  02A01     EXP-INTF                    244      PASS
  02A01     EXP-INTF                    316      PASS 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Test the System 
4-8 Test Time Division Multiplexing Bus for Each Expansion Port Network 
4
Test Time Division Multiplexing Bus
for Each Expansion Port Network
Check eac h TDM bus for each Expansion Port Network (EPN) in the system.
1. Verify the sc reen d isp lays command:
2. Type test tdm port-network 2
 and  p ress 
En t e r.
3. Verify a test results sc reen similar to Sc reen 4-7 is d isp layed :
Screen 4-7. Sample Test Results for Time Division Multiplexing Bus Port Network 2
4. If result is FAIL
 for any test, c hec k the c onnec tors of the TDM b us c ab les 
in  Pro c e ss o r  Po r t  N e t w o r k (PPN )  2 .
5. Rep eat these step s for eac h Exp ansion Port Network (EPN) to c hec k the 
TDM bus cables.
test tdm port-network 2 
                                  TEST RESULTS
   Port      Maintenance Name  Alt. Name Test No. Result            Error Code
   PN 02A    TDM-BUS                     294      PASS
   PN 02A    TDM-BUS                     296      PASS
   PN 02A    TDM-BUS                     297      ABORT             1005
   PN 02B    TDM-BUS                     294      PASS
   PN 02B    TDM-BUS                     296      ABORT             1005
   PN 02B    TDM-BUS                     297      PASS
 Command successfully completed 
 Command: 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Test the System 
4-9 Test Tone-Clock for Each Expansion Port Network 
4
Test Tone-Clock for Each Expansion 
Port Network
1. Verify the sc reen d isp lays command:
2. Type test tone-clock 2A
 where 2A 
is the c abinet and  c arrier numb er for 
one of the Tone-Cloc ks installed , and  p ress 
En t e r.
If any result is FAIL
, c hec k the assoc iated  TDM b us c ables and  
interc ab inet c ab les in the Exp ansion Port Network (EPN).
3. Rep eat Step  2 for eac h installed  Tone-Cloc k c irc uit pac k.
Test Tone-Clock Interchange for Each
Expansion Port Network
If the system is c ritic al reliab ility, test the Tone-Cloc k interc hang e for eac h 
Exp a n si o n  Po r t  N e t w o rk  ( EPN ).
1. Verify the sc reen d isp lays command:
2. Type status system all-cabinets
 and press 
En t e r. This d isp lays the 
loc ation of the Stand b y Tone-Cloc k.
3. Type set tone-clock xx
 where xx
 is the Port-Network/Carrier for the 
St a n d b y  To n e - C lo c k .  Pre s s  
En te r.
4. Type status system all-cabinets
 and press 
En t e r.
5. Verify the dup lic ated  Tone-Cloc k is ac tive using  the information d isplayed  
on the sc reen.
If any p rob lems are ind ic ated , c hec k the TDM c ab les in the assoc iated  
Exp a n si o n  Po r t  N e t w o rk  ( EPN ). 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Test the System 
4-10 Test Expansion Interface Exchange for Each Expansion Port Network 
4
Test Expansion Interface Exchange for
Each Expansion Port Network
If the system is c ritic al reliab ility, test the exp ansion interfac e exc hang e for eac h 
Exp a n si o n  Po r t  N e t w o rk  ( EPN ).
1. Verify the sc reen d isp lays command:
2. Type status system all-cabinets
 and press 
En t e r.
This d isp lays the stand b y exp ansion link. See Sc reen 4-8
.
Screen 4-8. Sample of System Status before Expansion Link is Set
3. Type set expansion-link xxxx 
where xxxx 
is the either one of the c ab inet, 
c arrier, and  p ort loc ations of the standb y exp ansion link.
4. Verify the sc reen d isp lays:
Command successfully completed
Command:
5. Type status system all-cabinets 
and press 
En t e r. A sc reen similar to 
Sc reen 4-9
 is displayed.
 status system all-cabinets 
                            SYSTEM STATUS CABINET 1
 EMERGENCY     SELECT                    SERVICE              CABINET
 TRANSFER      SWITCH      EXP-LINK      STATE     MODE       TYPE
 1A            unavail     01A01-02A01    in       standby    ESCC
 1B            auto-on     01B01-02B02    in       active
                                -
                                -
 Command successfully completed
 Command: 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Test the System 
4-11 Check Circuit Pack Configuration 
4
Screen 4-9. Sample of System Status after Expansion Link is Set
6. Verify the MODE
s of the exp ansion links have c hang ed .
7. If any prob lems are ind ic ated , c hec k the TDM c ab les and  the inter-c ab inet 
c ab les (ICC) in the assoc iated  Exp ansion Port Network (EPN).
Check Circuit Pack Configuration 
1. Verify the sc reen d isp lays command:
2. Type list configuration all
 and  p ress 
En t e r.
3. Verify all circuit packs are listed in the reports.
Refer to 
DEFINITY Enterp rise Communic ations Server Release 8 
Maintenanc e for R8si
, to resolve any d isc rep anc ies.
Save Translations, if Required
If any ad ministration c hang es have b een mad e, save and  make a b ac k up c op y 
of the translations. See Chap ter 3, ‘‘Ac c essing  and Ac tivating  the System’’
 for 
instruc tions.
status system all-cabinets 
                            SYSTEM STATUS CABINET 1
 EMERGENCY     SELECT                    SERVICE              CABINET
 TRANSFER      SWITCH      EXP-LINK      STATE     MODE       TYPE
 1A            auto-on     01A01-02A01    in       active     ESCC
 1B            auto-on     01B01-02B02    in       standby
 Command successfully completed
 Command: 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Test the System 
4-12 Next Steps 
4
Next Steps
1. Install the telep hones and  other equip ment. These p roc ed ures are in 
Chapter 5, ‘‘Install and  Wire Telep hones and  Other Eq uip ment’’
.
2. Ad minister the features, telep hones, and other eq uipment ac c ord ing  to 
c ustomer d ata found  on the p rovisioning  p lan. Use the p roc ed ures in 
DEFINITY Enterp rise Communic ations Server Release 8 Ad ministration 
and  Feature Desc rip tion
.
3. After the system is administered , test the telep hones and  other eq uip ment 
using Chap ter 6, ‘‘Test Telep hones and  Other Eq uip ment’’
.
NOTE:
It may b e more effic ient to install eac h hard ware c omp onent, 
ad minister it, and test it b efore g oing  on to install another 
c omp onent. As an examp le, install the attend ant c onsole using  the 
p roc ed ures in Chap ter 5, ‘‘Install and  Wire Telephones and  Other 
Eq uip ment’’, ad minister it using  the p roc ed ures in DEFINITY 
Enterprise Communic ations Server Release 8 Ad ministration and  
Feature Desc rip tion
, and  test it using  the p roc ed ures in Chap ter 6, 
‘‘Test Telep hones and  Other Eq uip ment’’.
!CAUTION:
To p revent unnec essary troub le tic kets, d o not enab le the system 
alarms (Alarm Orig ination feature) until all installation and  
ad ministration p roc ed ures are c ompleted . 
						

							Install and Wire Telephones and Other Equipment 
5-1 Voice and Data Terminals 
5
DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
5
Install and Wire Telephones and
Other Equipment
The wiring  p roc ed ures are the same for most of the DEFINITY System telep hones 
and  other eq uip ment. This sec tion p rovid es wiring  examp les of these similar 
installation p roc ed ures. These are examp les only and  ac tual wiring  p roc ed ures 
may vary at eac h site. All wiring  p inouts for all c irc uit p ac ks in this c hap ter c an b e 
found  in the tab les at the end  of this c hap ter.
Voice and Data Terminals
The system c an b e c onnec ted  to all DTE terminals and  have RS-232 (or EIA-232) 
or DCP interfac es.
Telephone Connection Example
The 302C1 Attend ant Console is used  to desc rib e a typic al telep hone 
c onnec tion. This information is typ ic al of the 603E, 84xx (4-wire), and  94xx 
telep hones. 
The attend ant c onsole always req uires auxiliary (ad junc t) power (-48 VDC). 
Power is c onnec ted  to the c onsole throug h Pins 7 and 8 of the information outlet. 
See Fig ure 5-1
. Only three c onsoles c an b e powered  b y the system throug h the 
AUX c onnec tor. When p ossib le, the p rimary c onsole should b e p owered from the 
system so it has the same p ower failure b ac kup  as the system.
The maximum c abling  d istanc e for the c onsole p owered  from the c ab inet is 350 
feet (100 meters). 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-2 Telephone Connection Example 
5
The g eneral step s to c onnec t a telep hone are: 
1. Choose a d evic e to c onnec t suc h as a 302C1 Attend ant Console.
2. Choose the port circuit pac k and its carrier and slot number, such as 
c ab inet 1, c arrier C, slot 02.
3. Choose a p ort c irc uit on the p ort c irc uit pac k. Suc h as Port 05.
Figure 5-1. 302C1 to 4-wire DCP Wiring
4. Install c ross-c onnec t jump ers to wire the terminal to the p ort c irc uit p ac k. 
See Fig ure 5-1
. This p inout is for the 4-wire Dig ital Line c irc uit p ac k.
5. For terminals need ing  ad junc t p ower, wire -48 VDC and  g round  to 
ap p rop riate p ins on the terminal. See Fig ure 5-1
. Figure Notes
1. 302C1 Attend ant Console
2. 4-wire Dig ital Line Circ uit Pac k 
(Position 1C02)3. -48 VDC From Ad junc t Power
4. Ground  From Ad junc t Power
302cwire RBP 040596
139
14
40
15
2
3
6
7
8
TXT
TXR
PXT
PXRTXT5
TXR5
PXT5
PXR5