Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-63 Install Multi-point Adapters 
5
367A Adapter
The 367A is an 8-c onduc tor ad ap ter used  at the work loc ation to b ridg e 3 to 7 
terminals. See Fig ure 5-25
.
Figure 5-25. Wiring Diagram of 367A Adapter Figure Notes
1. Jac k 1
2. Jac k 23. Jac k 8
4. 367A Adap ter
312 88 877 766 655 544 433 322 211 1
4 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-64 Install Multi-point Adapters 
5
Basic Multi-point Installation Distances
Fi g u re  5 - 2 6 p rovid es c ab ling  information for fan-out of ISDN-BRI multi-p oint 
installations. In Fig ure 5-26
, the terminating resistor is loc ated  in the satellite 
c loset. All d istanc es assume 24 AWG (#5) (0.5 mm2) D-Insid e Wire (DIW).
Figure 5-26. Basic Multi-point with One Work Location Figure Notes
1. S-Interfac e Sourc e (TN556)
2. Terminating  Resistor
3. Satellite Closet
4. Maximum Distanc e from S-Interfac e 
Sourc e to Work Loc ation (1600 
Feet) (488 m) 
5. Maximum Distanc e From 
Terminating  Resistor to Work 
Loc ation (250 Feet) (76 m)6. System Cab inet 
7. Terminating  End point 1 
8. Terminating  End point 2 
9. Work Loc ation
10. Maximum Distanc e from 
Information Outlet to Terminating  
Endp oint (33 Feet) (10 m)
11. Information Outlet
2
38
9
7
110
11
11
5
4
6
inst_dis CJL 030796 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-65 Connect Stratum 3 Clock 
5
Connect Stratum 3 Clock
Set Clock Options
1. There are four sets of op tion switc hes on the c loc k. Set the op tions on the 
Cloc k Inp ut (CI) c irc uit p ac k p er Tab le 5-15
.
2. Set the options on the Stratum 3 Clock (ST3) circuit pack per Tab le 5-16.
NOTE:
Only SW 1 and  SW2 are used . SW1 c ontrols the outp ut of alarm sig nals 
from the Stratum 3 Clock circuit pack.
3. Set the options on the Comp osite Cloc k Timing  Outp ut (TOCA) c irc uit 
pack per Table 5-17
.
4. Set the Stratum 2/Stratum 3 switc h to the STRATUM 3 p osition.
Table 5-15. CI Option Switch Settings
Switch Function Position
1 T1 Selec t OFF =  enab le (d efault)
ON = disable
2 CC Selec t OFF =  enab le
ON = disable (default)
3 Fra m i n g  Se l e c t O FF =  ESF
ON =  D4 (d efault)
4 BX.25 OFF =  enab le
ON = disable (default)
Table 5-16. ST3 Clock Circuit Pack Option Switch Settings
Switch Status/Results
SW1  
Minor Alarm 
ControlOFF =  minor alarm never outp ut
ON =  minor alarm is outp ut if hold over oc c urs
SW2  
Major Alarm 
ControlOFF =  major alarm is outp ut and  fail lamp  lig hts if 5 VDC 
p ower is lost and  4 kHz outp ut is lost
ON =  major alarm is outp ut and  fail lamp  lig hts if 5 VDC 
p ower is lost and  4 kHz outp ut is lost and  hold over oc c urs 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-66 Connect Stratum 3 Clock 
5
NOTE:
Set switc hes 1 and  2 ac cording to the d istanc e from the Stratum 3 c loc k to the DEFINITY 
System. Set switch 3 to ON. Set switc h 4 to OFF.
Cabling the Stratum 3 Clock
Figure 5-27 shows typ ic al c onnec tions to a Stratum 3 Cloc k c ab inet. Connec tions 
are mad e throug h the yellow field  c ross-c onnec t. A c ustom Y c ab le (H600-274) 
c onnec ts the CSU to the DS1 c irc uit p ac k and  tap s off the inp ut for the Stratum 3 
Cloc k. A resistor b uilt into the c ab le to p rovid es the nec essary isolation b etween 
the system and  the c loc k. The Y c ab le p lug s d irec tly into the CSU and  c onnec ts 
to stand ard  c ab les for interfac e to the system and the yellow field on the MDF.
The H600-307 c ab le c onnec ts the system end of the Y c ab le to a DS1 c irc uit 
p ac k (shown as TN464/2464, TN722, or TN767). The B25A c ab le c onnec ts the 
c loc k end of the Y c ab le to the yellow field on the MDF.
Table 5-17. Composite Clock Timing Output (TOCA) Circuit Pack
 Switch  Range
500 10001 Foot
(0.3 m)500 Feet
(152 m)1000 Feet
(305 m)1500 Feet
(457 m)2000 Feet
(610 m)2500 Feet
(762 m)3000 Feet
(914 m)
OFF OFF < ------------------------------------------------------->
ON OFF < --------------------------------------------------------->
OFF ON < --------------------------------------------------------->
ON ON < ---------------------------------------------------------> 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-67 Connect Stratum 3 Clock 
5
Figure 5-27. Typical Connections to Stratum 3 Clock Figure Notes:
1 . SC C  C a b in e t  ( PPN )
2.“A” Position
3. “ B”  Position
4. H600-307 Cab le
5. H600-247 G2 Cab le
6. 1300 Feet (396 m)
7. B25A (Male-to-Female) Cable
8. Channel Servic e Unit (Sec ond ary)9. Channel Servic e Unit (Primary)
10. Stratum 3 Cloc k
11. Main Distrib ution Frame (MDF)
12. DS1/E1 Interfac e Circ uit Pac k
13. DS1 Tie Trunk Circ uit Pac k
14. DS1 Interfac e Circ uit Pac k
15. Tone-Cloc k Circ uit Pac k 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-68 Connect Stratum 3 Clock 
5
Stratum 3 Clock Wiring Installation Procedure
1. Connec t the B25A c ab les from the TN780 c onnec tor panel slot on the 
system c ab inet and  the Stratum 3 Cloc k to the c ross-c onnec t mod ule in 
the yellow field .
2. Connec t the CSU p lug end  of the H-600-274 (Y) c ab le to the p rimary CSU. 
Route an H600-307 c ab le from the DS1 c onnec tor panel slot on the 
system c ab inet to the c onnec tor on the SYSTEM  e n d  o f  t h e  Y c a b le .
3. Route a B25A c able from the CLOCK end of the Y c ab le to the 
c ross-c onnec t module in the yellow field.
4. Rep eat steps 2 and  3 for the sec ond ary CSU. The maximum allowab le 
c ab ling d istanc e b etween the Stratum 3 c loc k and  the CSU is shown in 
Tab le 5-18
.
5. For stand ard  reliab ility systems, refer to Tab le 5-19 to c ross-c onnec t the 
TN780 and  CLOCK end  c onnec tions to the Stratum 3 Cloc k c onnec tions 
on the c ross-c onnec t mod ule.
6. For hig h or c ritic al reliab ility systems, refer to Tab le 5-20
 to cross-connect 
the TN780 and  CLOCK end  c onnec tions to the Stratum 3 Cloc k 
c onnec tions on the c ross-c onnec t mod ule.
Table 5-18. Maximum Cabling Distance
Channel Service 
Unit (CSU)Maximum Cabling 
Distance
551A 85 Feet (26 m)
551V 85 Feet (26 m)
5 5 1 V EFS/ R 6 5 5  Fe e t  ( 1 9 9 . 6  m )
EFS T1 655 Feet (199.6 m) 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-69 Connect Stratum 3 Clock 
5
Table 5-19. Cross-Connects for Standard Reliability
From: Stratum 3 Clock To: Y Cable Clock End (Primary)
Lead 
DesignationLead 
ColorConnecting 
Block 
Te r m i n a lLead 
DesignationLead 
ColorConnecting 
Block 
Te r m i n a l
RREF1 W- BL 1 V- O 4 3
TREF1 B L - W 2 O - V 4 4
To: Y Cable Clock End (Secondary)
 RREF2 W- O 3 V- O 4 3
 TREF2 O - W 4 O - V 4 4
To: Tone-Clock Carrier A
 BCLKRTN R-O 13  ALRM5B V-G 45
 BCLKLST O-R 14  ALRM5A G-V 46
 BPWRRTN R-BR 17  ALRM4B BK-BL 21
 B PWRL ST B R- R 1 8  A L RM 4 A B L - B K 2 2
 REF2 RTN W- B R 7  A L RM 3 B R- B R 1 7
 REF2 L ST B R- W 8  A L RM 3 A B R- R 1 8
 SC L K RTN R- B L 1 1  A L RM 2 B R- B L 1 1
 SCLKLST BL-R 12  ALRM2A BL-R 12
 SPWRRTN R-G 1 5  A L RM 1 B Y- BL 3 1
 SPWRLST G-R 16  ALRM1A BL-Y 32
 REF1 RTN W- G 5  A L RM 0 B W- B R 7
 REF1LST G-W 6  ALRM0A BR-W 8
 C C A 0 1 R R-S 1 9  EXTSYN 0 T V- BL 4 1
 C C A 0 1 T S- R 2 0  EXTSYN 0 R B L - V 4 2
 C C B 0 1 R B K- B L 2 1  EXTSYN 1 T Y- G 3 5
 C C B 0 1 T B L - BK 2 2  EXTSYN 1 R G - Y 3 6 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-70 Connect Stratum 3 Clock 
5
7. The c ommon c ross-c onnec tion from the TN780 in A and  B c arriers to the 
Stratum 3 Cloc k should  b e d one b y brid ging  the jump er wires.
8. Dress the c ab les d own sid es of the c ab inet and  run throug h the Cable 
Slack Manager, if provided.
9. Ad minister p er 
DEFINITY Enterprise Communic ations Server Release 8 
Ad ministration and  Feature Desc ription
.
Table 5-20. Cross-Connects for High or Critical Reliability
From: Stratum 3 Clock To: Y Cable Clock End (Primary)
Lead 
Designation Lead 
ColorConnectin
g Block 
Terminal Lead 
Designation Lead 
ColorConnectin
g Block 
Te r m i n a l
RREF1  W-B L 1 V- O 4 3
TREF1  B L - W 2 O - V 4 4
To: Y Cable Clock End (Secondary)
RREF2  W-O 3  V-O 4 3
Lead 
Designation Lead 
ColorConnecting 
Block 
Te r m i n a l TREF2  O-W 4  O-V 44
To: Tone-Clock Carrier A To: Tone-Clock Carrier B
BCLKRTN  R-O 13  ALRM5B  V-G 45  ALRM5B  V-G 45
BCLKLST  O-R 14  ALRM5A  G-V 46  ALRM5A  G-V 46
BPWRRTN  R-BR 17  ALRM4B  BK-BL  21  ALRM4B  BK-BL  21
BPWRLST  BR-R 18  ALRM4A  BL-BK  22  ALRM4A  BL-BK  22
REF2RTN  W-BR 7  ALRM3B  R-BR 17  ALRM3B  R-BR 17
REF2LST  BR-W 8  ALRM3A  BR-R 18  ALRM3A  BR-R 18
SCLKRTN  R-BL 11  ALRM2B  R-BL 11  ALRM2B  R-BL 11
SCLKLST  BL-R 12  ALRM2A  BL-R 12  ALRM2A  BL-R 12
SPWRRTN  R-G 15  ALRM1B  Y-BL 31  ALRM1B  Y-BL 31
SPWRLST  G-R 16  ALRM1A  BL-Y 32  ALRM1A  BL-Y 32
REF1RTN  W-G 5  ALRM0B  W-BR 7  ALRM0B  W-BR 7
REF1LST  G-W 6  ALRM0A  BR-W 8  ALRM0A  BR-W 8
CCA 01R  R- S 19  EXTSYN0T  V-B L 4 1
CCA 01T  S-R 20  EXTSYN0R  B L- V 4 2
CCB01R  BK-BL 21  EXTSYN1T  Y-G 35
CCB01T  BL-BK 22  EXTSYN1R  G-Y 36
CCA 02R  B K -O 23  EXTSYN0 T  V- B L 41
CCA02T  O-BK 24  EXTSYN0R  BL-V 42
CCB 02R  B K -G 25  EXTSYN1 T  Y- G 35
CCB02T  G-BK 26  EXTSYN1R  G-Y 36 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-71 DEFINITY Wireless Business System 
5
DEFINITY Wireless Business System
To install and  test the hard ware, refer to DEFINITY Wireless Business System 
Installation and  Tests Guid e
.
To interfac e the Wireless Business System to the system c ab inet, refer to 
DEFINITY Wireless Business System Interfac e.
To operate the wireless hand sets, refer to 
DEFINITY Wireless Business System 
User’s Guid e
.
Cellular Business System
The DEFINITY Cellular Business System allows use of the same full-feature 
c ellular telep hone insid e and  outsid e of the b uild ing. The system sup p orts up  to 
600 users. Total system c overag e is up  to 4 million sq uare feet.
Refer to the installation and  usag e d oc umentation that c omes with the system 
c omp onents.
Forum PCM
The Forum Personal Communic ations Manager uses a Forum switc h, serving  as 
an ad junc t to DEFINITY ECS, to manag e mob ility. The system uses Cord less 
Telep hone Generation 2 (CT2) tec hnology, whic h is a g lob al standard  for wireless 
telep hone servic e. This stand ard  d efines the rad io interfac e b etween the Forum 
p oc ket telep hones and  the b ase stations in the system.
Refer to the installation and  usag e d oc umentation that c omes with the Forum 
Personal Communic ations Manag er c omp onents. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-72 Connect Modem to Telephone Network 
5
Connect Modem to Telephone 
Network
1. Cross-c onnec t the network jac k on the mod em to the network interfac e 
(via a 103A or mod ular wall jac k). See Table 5-21
 for the p inout.  
Figure 5-28. Network Jack on U.S. Robotics Modem
Table 5-21. Pinout of Network Jack
Pin Number Signal
1 Unused
2Tip 
3Ring 
4 Unused
Figure Notes
1. Pin 1 of network jac k 2. Mod em 
modmcabl KLC 110397
OFF ON
AA CD RD SD C S AR Q/ FAXTR
Sportster33.6
Faxmodem
1
2