Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-93 Add CallVisor ASAI 
5
Add CallVisor ASAI
Service Interruption
1. If ad d ing  the pac ket b us sup p ort and  TN570s must b e installed  as part of 
that sup p ort, then ad d ing  CallVisor ASAI req uires a servic e interrup tion. 
Notify the c ustomer in ad vanc e as to when the ad d ition will take p lac e. 
See ‘‘Add Packet Bus Support to R8si’’ on page 5-87
 for further 
information.
Enter Added Translations
1. On the System-Parameters Customer-Op tions form, disab le the Calling  
Party Numb er/Billing  Numb er (CPN/BN) op tion, and  enab le the CallVisor 
ASAI Interfac e op tion. 
2. See 
DEFINITY Enterp rise Communic ations Server Release 8 
Ad ministrator’s Guid e
, for d etails on d isab ling  and  enab ling these op tions.
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard s.
Add Packet Bus Support
1. If p ac ket b us sup p ort is not alread y installed , see ‘‘Add Packet Bus 
Support to R8si’’ on page 5-87 and  p erform the step s. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-94 Add CallVisor ASAI 
5
Add Circuit Packs
1. Determine port assig nment of c irc uit p ac ks to be ad d ed .
2. Install the ap p rop riate c irc uit pac ks in assigned  c ab inet slot (as req uired ).
The TN748B (or later) or TN744/C/D Call Classifier c irc uit p ac k is req uired . 
The TN744 is req uired  for those c ustomers who d esire switc h c all 
c lassific ation.
A vac ant p ort is req uired on a TN556/B ISDN—BRI circuit pack.
Install Cables
1. Install c ab les from c ab inet to the MDF as req uired .
Enter Added Translations
1. Ad minister the req uired  translation d ata using the forms listed und er 
“ Ad junc t/Switc h Ap p lic ations Interfac e (ASAI)”  in 
DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e
.
Resolve Alarms
1. Examine the alarm log. Resolve any alarms that may exist using  D EFI N I TY 
Enterp rise Communic ations Server Release 8 Maintenanc e for R8si
. 
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard s.
3. Up d ate b ac kup  translation c ard s, if required .
EXAMPLE:1 A 07 01
Cab inet (Port 
Network)Carrier Slot 
Numb erPo rt  
Number 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-95 Add ISDN—BRI 
5
Add ISDN—BRI
Service Interruption
1. If ad d ing  the pac ket b us sup p ort and  TN570s must b e installed  as part of 
that sup p ort, ad d ing ISDN—BRI req uires a servic e interrup tion. Notify the 
c ustomer in ad vanc e as to when the ad d ition will b e c arried  out. See ‘‘Add 
Packet Bus Support to R8si’’ on page 5-87 for further information.
Add Packet Bus Support
1. If p ac ket b us sup p ort is not alread y installed , see ‘‘Add Packet Bus 
Support to R8si’’ on page 5-87 and  p erform the step s.
Add Circuit Packs
1. Determine port assignments of circuit packs to be added.
2. Install the ap p rop riate c irc uit pac ks in assigned  c ab inet slot (as req uired ).
Required circuit packs:
nTN794 Network Control/Pac ket Interfac e (Net/Pkt) c irc uit p ac k
nTN556 or TN2198 ISDN BRI c irc uit p ac k.
nTN570/B/C Exp ansion Interfac e c irc uit p ac k (if EPN p resent)
Ad d  the TN794 Pac ket Interfac e c irc uit p ac k first.
Install Cables
1. Install the c ab les from the c ab inet to the MDF as req uired .
NOTE:
A TN556 ISDN BRI req uires an 8-p ort b ac kplane c ab le terminator 
(b reakout c onnec tor); aTN2198 ISDN BRI req uires a 12-p ort 
b ac kp lane c ab le terminator. Connec t the 25-p air c ab le to the 
ap p rop riate terminator.
EXAMPLE:1 A 07 01
Cab inet (Port 
Network)Carrier Slot 
Numb erPo rt  
Number 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-96 Add IP Interface Assembly 
5
Enter Added Translations
1. Ad minister the req uired  translation d ata using the forms listed und er 
7500D voic e terminals and  8500 voic e terminals in 
DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e
.
Resolve Alarms
1. Examine the alarm log . Resolve any alarms using  DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8si
. 
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard s.
3. If the system c ontains a TN750/B/C Announc ement c irc uit pac k, typ e list 
configuration software-version
 and  p ress 
En t e r. To restore these 
announc ements, typ e restore announcements
 and  press 
En t e r.
4. Update backup cards, if required.
Add IP Interface Assembly
DEFINITY ECS IP Solutions allows you to send  voic e and  fax from the DEFINITY 
ECS throug h an Internet p rotoc ol (IP) network to other DEFINITY ECSs having  
this feature or to other H.323 V2 c omp liant end p oints. It is imp lemented  using  the 
TN802/B IP Interfac e, whic h is a Wind ows NT server resid ing  on the IP Interfac e 
Assemb ly insid e the DEFINITY ECS.
The IP Interfac e is an assemb ly c omp osed  of a TN802B c irc uit b oard, a 
p roc essor c ard , and DSP resourc e c ard . For ord ering  p urp oses, the assemb ly is 
id entified  as a J58890MA-1 L30, b ut for simp lic ity, we refer to it in this b ook as the 
TN802B IP Interfac e.
The TN802B IP Interfac e op erates in two mod es: IP Trunk, availab le with Release 
7 or later, and  Med ia Proc essor (Med Pro), availab le with Release 8. The IP Trunk 
mod e is Internet Telep hone Server—Enterp rise (ITS-E) c omp atib le, and  the 
Med Pro mod e is H.323 V2 c omp atib le. The TN802B IP Interfac e is b ac kward s 
c omp atib le and  d efaults to IP Trunk mod e.You must ad minister it to use it in 
Med Pro mod e.
For more information on the IP Interfac e c ap ab ilities and  limitations, refer to the 
DEFINITY Enterp rise Communic ations Server Release 8 Overview. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-97 Add IP Interface Assembly 
5
The following sec tions d esc rib e the proc ess for
nInstalling  in Med ia Proc essor Mod e
nInstalling  in IP Trunk Mod e
nUp g rad ing  a TN802 V3 (or later) to a TN802B (Med Pro mod e)
!WARNING:
When c onnec ted  remotely via p c ANYWHERE, only use the p c ANYWHERE 
Restart Host Computer b utton on the toolb ar to restart Wind ows NT.
Installing in Media Processor Mode
To operate in Med Pro mod e, you must install the TN802B IP Interfac e and , if the 
system d oes not have one, you must also install and  administer a TN799B
 C-LAN 
c irc uit p ac k. For C-LAN administration, refer to 
DEFINITY Enterprise 
Communic ations Server Ad ministration for Network Connec tivity.
If you have existing  TN802 IP Interfac e c irc uit p ac ks, you c an up g rad e them 
either b y rep lac ing  the c irc uit p ac k with a TN802B or b y d ownload ing  the 
TN802B firmware onto the c irc uit p ac ks (see ‘‘Up g rad e to TN802B (R8)’’ on p ag e 
5-126). 
Prepare for Installation
Have the following  eq uip ment on site b efore your ship ment arrives:
nAC p ower outlets for the mod em and  monitor.
nThree unoc c up ied  and  ad joining  p ort slots in the DEFINITY ECS for the 
TN802B IP Interfac e, if need ed.
The TN802B oc c up ies only one slot, b ut it need s the two slots to its left for 
c learanc e.
nAn ad d itional unoc c up ied  p ort slot for the TN799B, if need ed . If you have 
an existing TN799 c irc uit p ac k, rep lac e it with the TN799B.
nA 10 BaseT or 10/100 BaseT Ethernet c onnec tion into your loc al area 
network for the TN802B.
nA 10 BaseT Ethernet c onnec tion into your loc al area network for the 
TN799B.
nTwo or more valid , unused  IP ad d resses on your network (one for MedPro 
and  one for C-LAN) that c an b e assig ned  to the IP Interfac e server. You 
also need  the subnet mask and  d efault g ateway. 
nAn analog telep hone line reserved  (DID is okay) for the IP Interfac e 
diagnostic modem 
nA valid  telep hone numb er reserved  for the IP Interfac e d iag nostic  mod em  
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-98 Add IP Interface Assembly 
5
In ad dition if non-U.S. c ustomer:
nMod em c omp arab le to a U.S. Rob otic s Sportster Mod el USR 33.6 EXT.
nCable from modem to TN802B external c able assembly.
We rec ommend  that you p rotec t your c ab inet with an uninterrup tib le power 
system (UPS).
Check your Shipment
When your DEFINITY IP Trunk ord er arrives at your site, c hec k the c ontents (see 
Tab le 5-28
).
1. Insp ec t the ship p ing  c arton for d amag e b efore op ening  it. If the b ox is 
damaged, 
do not open it. Inform the ship p ing  c omp any, and  ask for 
instruc tions on filing a c laim.
2. If the b ox is und amag ed , c hec k the c ontents ag ainst the p ac king  slip . 
Chec k the c ondition of eac h c omp onent, and note any d amag e or 
shortag es on the p ac king  slip . The c arton should  c ontain the following  for 
eac h IP Interfac e ord ered :
3. Read  and  follow any d irec tions inserted  into the p ac kag e b y the fac tory.
The TN802B external c ab le assemb ly is a bund le of c ab les with an amp henol 
c onnec tor at the end  of the b und le and  various PC-typ e c onnec tors (VGA, 
Universal Serial Bus [ USB] , mouse, keyb oard , Ethernet, mod em, and  COM2) at 
the end s of the ind ivid ual c ab les. See Fig ure 5-30
. Look for the lab el where the 
b und le enters the amp henol c onnec tor. 
Table 5-28. Required Hardware
Comcode/Code Description Quantity
108525528 TN799B C-LAN c irc uit p ac k. One TN799B 
sup ports more than one TN802B.1
J58890MA-1 L30 TN802B IP Interfac e Assemb ly
1 or more
601939804 H600-512,G1 external c ab le assembly 1 or more
259A c onnec tor 1
CAT5 or b etter c ab le 1
407633999 U.S. Rob otic s Sp ortster external mod em, 
Mod el USR 33.6 EXT (U.S. c ustomers 
only). Non-U.S. c ustomers must p rovid e a 
mod em c omp arab le to this mod el.1
601087091 20-ft DB-25 serial c ab le from mod em to 
TN802B external c ab le assemb ly (U.S. 
c ustomers only). Non-U.S. c ustomers must 
p rovid e a serial c ab le.1 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-99 Add IP Interface Assembly 
5
Figure 5-30. TN802B IP Interface External Cable Assembly
Connect the Cables
1. Determine into whic h p ort slots you are p utting the TN799B C-LAN and  
TN802B IP Interfac e c irc uit p ac ks.
NOTE:
Make sure that at least 3 ad jac ent slots are free for the TN802B.
From the rear of the c ab inet:
2. If add ing  a new TN799B, c onnec t the 259A c onnec tor to the b ac kp lane 
c onnec tor c orrespond ing  to the TN799B slot.
3. If add ing  a new TN799B, c onnec t one end  of the DW8 c able to the 259A 
c onnec tor. Connec t the other end  to the c ustomer’s network.
4. Connec t the amp henol c onnec tor on the external c ab le assemb ly to the 
b ac kp lane c onnec tor c orresp ond ing  to the TN802B slot (the hig hest 
numb ered c onnec tor of the 3 slots req uired ) Figure Notes
1. Amp henol c onnec tor to c onnec tor 
c orresp ond ing  to TN802B slot
2. To VGA monitor
3. To USB (not used )
4. To keyb oard5. To mouse
6. To ethernet
7. 25-p in male c onnec tor to mod em
8. 25-p in male c onnec tor to COM2 
cbdfocto AWF 122398
2
1
345678 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-100 Add IP Interface Assembly 
5
Connect the Modem
NOTE:
These instruc tions are for c onnec ting  the U.S. Rob otic s modem sup p lied  to 
U.S. c ustomers only. If using  a d ifferent mod em, follow the manufac turer’s 
instruc tions on c onnec ting  the mod em.
1. Connec t the RS232 p ort of the mod em to the MODEM c onnec tor of the 
TN802B external c ab le assembly. 
NOTE:
Chec k the lab els near the c onnec tors; the MODEM and  COM2 
c onnec tors look the same.
2. Connec t an analog  telephone line to the left most analog -line p ort on the 
mod em as shown in Fig ure 5-31
. 
3. Make sure that the mod em’s DIP switc hes are set as shown in 
Fi g u re  5 - 3 1
 and Tab le 5-29.
4. Plug  the mod em into an AC p ower outlet.
5. Turn on the mod em using  the switc h on the front of the mod em.
Figure 5-31. External Modem Connections for U.S. Robotics Modem Figure Notes
1. Connec t analog  line here.
2. DIP switc h 5 must b e up .3. Connec t MODEM c onnec tor here.
4. Connec t p ower c onnec tor here.
12345678
modfrobo KLC 030499
234
1 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-101 Add IP Interface Assembly 
5
Connect the Ethernet
1. Connec t the network c ab le to the ETHERNET c onnec tor on the TN802B 
external c ab le assemb ly.
NOTE:
You need  a CAT5 or better c ab le for 100-Mb yte operation.
Install the Circuit Packs
!CAUTION:
When add ing  or rep lac ing  any hard ware, b e sure to g round  yourself against 
elec trostatic  d isc harg e (ESD) b y wearing  a g round ed  wrist strap .
NOTE:
The TN799B and  TN802B c irc uit p ac ks are hot-swap p ab le, so you d o not 
need  to p ower d own the c arrier to install them.
If you need  to remove the TN802B IP Interfac e from the c arrier at a later 
time, shut down Wind ows NT first b y p ressing the rec essed reset button on 
the fac ep late (see Figure 5-32
) of the TN802B IP Interfac e until the LCD 
shows a flashing MSHUT *
. When the flashing  stop s and  the asterisk 
d isap p ears (ab out 2 min), it is safe to remove the c irc uit p ac k.
Table 5-29. U.S. Robotics Modem Dip Switch Settings
Dip 
Switch Setting Description
1UP
DOWNData Terminal Read y normal
Data Terminal Read y overrid e
2UP
DOWNVe r b a l  r e s u lt  c o d e s
Numeric  result c od es
3UP
DOWNSuppress result codes
Disp lay result cod es
4UP
DOWNEc ho offline c ommand s
No ec ho, offline c ommand s
5UP
DOWNAuto answer on first ring or higher if specified in NVRAM
Auto answer off
6UP
DOWNCarrier d etec t normal
Carrier d etec t overrid e
7UP
DOWNLoad  NVRAM d efaults
Load  fac tory d efaults
8UP
DOWNDumb  mod e
Sm a rt  m o d e 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-102 Add IP Interface Assembly 
5
Figure 5-32. TN802B IP Interface faceplate
NOTE:
If rep lac ing  the existing  TN799 c irc uit p ac k, remove it first and rep lac e it 
with the new one.
1. Insert the TN799B c irc uit p ac k into the p ort slot id entified  earlier.
NOTE:
To p rop erly seat the c irc uit p ac k, p ush firmly on the front of the 
fac ep late until the latc h reac hes the bottom rail of the c arrier. Then 
c lose the latc h until it is fully eng ag ed . Figure Notes
1. LCD d isp lay
2. Reset b utton (rec essed )
3. Red  b oard  status LED4. PCMCIA c ard slot
5. Yellow PCMCIA d isk-in-use LED
1
2
3
4
5
fpdfmapd KLC 030899