Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-53 CAMA/E911 Installation 
5
Screen 5-4. Feature Access Code (FAC) form (page 1)
11. The Feature Ac c ess Cod e (FAC) sc reen (p ag e 1) ap p ears.
12. In the Auto Route Selection (ARS) Access Code 1:
 field, 
ad minister the ARS ac c ess c od e (in the examp le above, typ e 9
) and press 
En t e r  (must matc h d ial p lan).
13. At the promp t, enter change ars analysis 
  and p ress 
En t e r.
                                 Page 1 of 5
                                FEATURE ACCESS CODE (FAC)
             Abbreviated Dialing List1 Access Code: ____
             Abbreviated Dialing List2 Access Code: ____
             Abbreviated Dialing List3 Access Code: ____
Abbreviated Dial - Prgm Group List Access Code: ____
                          Announcement Access Code: ____
                           Answer Back Access Code: ____
          Auto Alternate Routing (AAR) Access Code: ____
          Auto Route Selection (ARS) Access Code 1: 9___  Access Code 2: ____
                     Automatic Callback Activation: ____   Deactivation: ____
Call Forwarding Activation Busy/DA: ____ All: ____  Deactivation: ____
                             Call Park Access Code: ____
                           Call Pickup Access Code: ____
   CAS Remote Hold/Answer Hold-Unhold Access Code: ____
                      CDR Account Code Access Code: ____
Change Coverage: ____
                      Data Origination Access Code: ____
                          Data Privacy Access Code: ____
Directed Call Pickup Access Code: ____
         Emergency Access To Attendant Access Code: ____
Extended Call Fwd Activate Busy D/A: ____  All: ____  Deactivation: ____
                   Facility Test Calls Access Code: ____
                                 Flash Access Code: ____ 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-54 CAMA/E911 Installation 
5
Screen 5-5. ARS Digit Analysis Table
14. On ARS Dig it Analysis Tab le sc reen app ears. In the Dialed String
 
field , in the first emp ty row, enter 11
.
15. In the Total Mn
 field , enter 2
.
16. In the Total Mx
 field , enter 2
.
17. In the Rte Pat
 field , enter the d esired  Route Pattern (in the examp le 
ab ove the route p attern is 11).
NOTE:
For the following  step , if you are using the Attend ant Crisis Alerting  
feature, typ e alrt
 instead  of “ emer.”
18. In Call Type
 field , enter emer
.
19. On the next emp ty row, in the Dialed String
 field , typ e 911
.
20. In the Total Mn
 field , enter 3
.
21. In the Total Mx
 field , enter 3
.
22. In the Rte Pat
 field , typ e the d esired  Route Pattern (in the example 
ab ove the route p attern is 12).
NOTE:
For the following  step , if you are using the Attend ant Crisis Alerting  
feature, typ e alrt
 instead  of “ emer.”
23. In the Call Type
 field , enter emer
 and press 
En t e r.
                              ARS DIGIT ANALYSIS TABLE
                            Partitioned Group Number:  _     Percent Full:    ___
Dialed      Total  Rte Call Nd  ANI Dialed      Total  Rte Call Nd ANI
     String      Mn Mx  Pat Type Num Rq String      Mn Mx  Pat Type Num Rq
9________________ 7_ 7_  2__ hnpa ___ n __________________ __ __ ___ ____ ___ _
976______________ 7_ 7_  den hnpa ___ n __________________ __ __ ___ ____ ___ _
11_______________ 2_ 2_  11_ emer ___ n __________________ __ __ ___ ____ ___ _
911______________ 3_ 3_  12_ emer ___ n __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _ 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-55 CAMA/E911 Installation 
5
24. At the p rompt, typ e change route-pattern 
 
(the route pattern to 
b e c hanged ; in the examp le b elow, the route pattern is 11) and  p ress 
En te r.
Screen 5-6. Route Pattern form (Page 1)
25. On the Route Pattern sc reen, in Grp. No
. field , enter the CAMA trunk 
g roup number.
26. In the FRL
 field , enter 0
.
NOTE:
For the following  step , if the Central Offic e (CO) wants KP11ST as 
the d ialed dig it string , then leave b lank. If the CO wants KP911ST, 
then insert a “ 9”  in the Inserted Digits
 field .
27. Ad minister the Inserted Digits
 field  if need ed  and  p ress 
En t e r.
                      Page 1 of X
  Pattern Number: 11               
    Grp.  FRL NPA Pfx Hop Toll No. Del Inserted                             IXC
    No.           Mrk Lmt List Digits  Digits
 1: 1__   0  ___  _  __   __    __    ____________________________________ user
 2: ___   _  ___  _  __   __    __    ____________________________________ user
 3: ___   _  ___  _  __   __    __    ____________________________________ user
 4: ___   _  ___  _  __   __    __    ____________________________________ user
 5: ___   _  ___  _  __   __    __    ____________________________________ user
 6: ___   _  ___  _  __   __    __    ____________________________________ user
BCC VALUE  TSC CA-TSC   ITC BCIE Service/Feature           Numbering LAR
0 1 2 3 4 W    Request                                       Format
  1: y y y y y n  y none_____ both ept  outwats-bnd____ BAND: ___ ________  none
  2: y y y y y n  n           rest      _______________           ________  next
  3: y y y y y n  n           rest      _______________           ________  rehu
  4: y y y y y n  n           rest      _______________           ________  none
  5: y y y y y n  n           rest      _______________           ________  none
  6: y y y y y n  n           rest      _______________           ________  none 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-56 CAMA/E911 Installation 
5
28. At the p rompt, typ e change route-pattern 
  (the route pattern to 
b e c hanged ; in the examp le b elow, the route pattern is 12) and  p ress 
En te r.
Screen 5-7. Route Pattern form (Page 1)
29. On the Route Pattern sc reen, in Grp. No
. field , typ e the CAMA trunk 
g roup number and  p ress 
En te r.
30. In the FRL
 field , typ e 0
.
NOTE:
For the following  step , if the Central Offic e (CO) wants KP911ST as 
the d ialed dig it string , then leave b lank. If the CO wants KP11ST, 
then d elete one d ig it.
31. Ad minister No. Del Digits
 field  if need ed  and  p ress 
En t e r.
32. At the promp t, type change cama-numbering
 and press 
En t e r.
                      Page 1 of X
  Pattern Number: 12               
    Grp.  FRL NPA Pfx Hop Toll No. Del Inserted                             IXC
    No.           Mrk Lmt List Digits  Digits
 1: 1__   0  ___  _  __   __    1_    ____________________________________ user
 2: ___   _  ___  _  __   __    __    ____________________________________ user
 3: ___   _  ___  _  __   __    __    ____________________________________ user
 4: ___   _  ___  _  __   __    __    ____________________________________ user
 5: ___   _  ___  _  __   __    __    ____________________________________ user
 6: ___   _  ___  _  __   __    __    ____________________________________ user
BCC VALUE  TSC CA-TSC   ITC BCIE Service/Feature           Numbering LAR
0 1 2 3 4 W    Request                                       Format
  1: y y y y y n  y none_____ both ept  outwats-bnd____ BAND: ___ ________  none
  2: y y y y y n  n           rest      _______________           ________  next
  3: y y y y y n  n           rest      _______________           ________  rehu
  4: y y y y y n  n           rest      _______________           ________  none
  5: y y y y y n  n           rest      _______________           ________  none
  6: y y y y y n  n           rest      _______________           ________  none 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-57 CAMA/E911 Installation 
5
Screen 5-8. CAMA Numbering Format form
33. In the CAMA Numb ering  - E911 Format sc reen (p ag e 1), in System 
CESID Default:
 field , enter your own system d efault and p ress 
En t e r. 
This is the numb er outp ulsed  when the extension c od e is not found in the 
CAMA Numb ering  tab le. See Sc reen 5-8
.
34. In the Ext Len
, Ext Code
, CESID
, and  Total Length
 field s, fill out to 
your own CAMA numb ering  p lan and  p ress 
En te r. Be sure to c over all 
extensions.
35. At the promp t, typ e change cor 
 
(the c lass of restriction (COR) 
to be changed) and press 
En t e r. Chang e all CORs that are defined  for 
stations in ord er to remove any c alling  p arty restric tions for 911 c alls.
                                                                     Page 1 of 3
                         CAMA NUMBERING - E911 FORMAT
System CESID Default: 5241100______
Ext  Ext                   Total         Ext  Ext                   Total
Len Code      CESID      Length         Len  Code      CESID      Length
4_  101__  5381234_____    7_             __  _____  __________     __
4_  1____  555_________    7_             __  _____  ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __
__  _____  ____________    __             __  ______ ___________    __ 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-58 Install the BRI Terminating Resistor 
5
Screen 5-9. Class of Restriction form (page 1)
36. On the Class of Restric tion sc reen (pag e 1), in the Calling Party 
Restriction:
 field , typ e none 
and  p ress 
En te r.
37. Typ e Save Translation
 and press 
En te r.
Install the BRI Terminating Resistor
The resistors balanc e the c able p lant b etween the rec eiver and  the transmitter on 
the interfac e. When using  the TN2198 ISDN-BRI 2-Wire U Interfac e c irc uit p ac k, 
an NT1 is req uired. A terminating resistor is always req uired  near the terminal 
when the BRI S-typ e interfac e c irc uit p ac k (TN556 BRI 4-Wire S-NT Line c irc uit 
p ac k) is used  (see 
# 5 ESS Sw i t c h  I n t e g r a t e d  Se r vi c e s D i g it a l N e t w o r k  C u s t o m e r  
Premises Planning  Guide
, 533-700-100).
The resistor is b uilt into the NT1 and  c an b e one of three values, d ep ending  on 
the c onfig uration and the distanc e from the NT1 to the ISDN terminal. The resistor 
value is c ontrolled  from the NT1. A terminating  resistor ad apter may b e needed  
near the terminal and  c an b e p lac ed  in the satellite c loset or work loc ation.
NOTE:
The 440A4 terminating  resistor and  110RA1-12 terminating  resistor b loc k 
are UL listed . Most new installations are the 110RA1-12 terminating  resistor 
b loc k. The following  installation instruc tions should b e ob served .
nNever install telep hone wiring  d uring  a lig htning storm.
nNever install telep hone jac ks in wet locations unless the jack is 
sp ec ific ally d esig ned  for wet loc ations.
 Page 1 of 3
CLASS OF RESTRICTION
               COR Number: 10
          COR Description: supervisor
                      FRL: 0 APLT? y
  Can Be Service Observed? n           Calling Party Restriction: none
Can Be A Service Observer? n Called Party Restriction: none
Time of Day Chart: 1  Forced Entry of Account Codes? n
         Priority Queuing? n                Direct Agent Calling? n
     Restriction Override: none Facility Access Trunk Test? n
     Restricted Call List? n Can Change Coverage? n
Unrestricted Call List?
            Access to MCT? y  Fully Restricted Service? n
Category For MFC ANI:   7  Hear VDN of Origin Annc.? n
         Send ANI for MFE? n_  Add/Remove Agent Skills? n
Hear System Music on Hold? y PASTE (Display PBX Data on Phone)? n
Automatic Charge Display? n 
Can Be Picked Up By Directed Call Pickup? n
Can Use Directed Call Pickup? n 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-59 Install the BRI Terminating Resistor 
5
nNever touc h uninsulated  wires or terminals unless the telep hone 
line has b een d isc onnec ted  at the network interfac e.
nUse c aution when installing  or mod ifying  telephone lines.
Terminating Resistor Adapter
Fi g u re  5 - 2 1 shows an 8-p in 440A4 terminating  resistor ad ap ter. The ad ap ter is 
three inc hes long  with an 8-wid e p lug  at one end , a short c ord , and  an 8-wid e 
jac k at the opp osite end .
Figure 5-21. 8-Wide Terminating Resistor Adapter (440A4) Figure Notes
1. 8-Wid e Plug
2. Cord3. Plastic  Housing
4. 8-Wid e Jac k
1
2
3
4
5
6
7
81
2
3
4
5
6
7
8
3
41
2
R RCC 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-60 Install the BRI Terminating Resistor 
5
Closet Mounted (110RA1-12)
The 110RA1-12 terminating  resistor bloc k is d esig ned to mount in the 
telec ommunic ations wire c loset. It c onsists of twelve 2-p air c irc uits and  p rovid es 
the 100 Ohm termination used  for ISDN-BRI c irc uits.
Figure 5-22
 shows the wiring  of the 110RA1-12. Three rows of 110D-4 c onnec tor 
b loc ks are mounted  on a p rinted  wire board  along  with c irc uit resistors and  
c ap ac itors. The b ottom row is d esig nated  as the inp ut row and  the top  and  
mid dle rows are d esig nated  as the outp ut rows. The c irc uit assemb ly is mounted  
on a stand ard  110A-100 p air mounting  b ase. The 110RA1-12 is ship p ed  with 
p rep rinted  d esig nation strip s to simp lify c irc uit id entific ation and  installation.
Figure 5-22. Terminating Resistor Block (110RA1-12) Figure Notes
1. Circ uit 1
2. Circuit 12
3.Outp ut Row “ A”
4. Outp ut Row “ B”
5. Input Row “ C”6. Only First Circ uit Shown to All 12 
Circ uits (2APR) Per Bloc k
7. 110D-4 Connec tor Bloc k
8. Printed  Circ uit Board  Mounted  on 
Stand ard  110A or 100APR Bloc k
3
8
4
5
1
6
2
7 145246347448 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-61 Install the BRI Terminating Resistor 
5
Fi g u re  5 - 2 3 shows the wiring c onnec tions for the 110RA1-12 terminal bloc k. The 
TN556 BRI switc h p ort is terminated  to b ottom row C.
Figure 5-23. Typical Installation of Terminating Resistor Block Using 
Multi-point Connection
For p oint-to-p oint wiring , the top  row is c onnec ted  to the blue station field . The 
p air c onnec ts from the 110RA1-12 to the stand ard 4-p air c irc uit. Pair 1 from the 
110RA1-12 is c onnec ted  to Pair 1 of the station field , and  Pair 2 is c onnec ted  to 
Pair 3 of the station field .
Two terminal basic  multi-p oint app lic ations are ac c ommod ated  b y c onnec ting  
row B (outp ut) to the sec ond terminal c ommon to the multi-p oint c irc uit.Figure Notes
1. Part of Terminating Resistor Bloc k
2. White or Purp le Field
3. Part of 4-Pair Blue Field
4. From ISDN T-interfac e Circ uit 
(2-Pair)
5. To ISDN S/T-interfac e Terminals
6. 2-Pair Cross-Connec t7. Basic  Multi-p oint Op tion
8. 2-Pair Cross-Connec t
9. 4-Pair Horizontal Cab les
10.Ro w  “ A ”
11. Row “ B”
12. Row “ C”
TT1RR1
10
3
45
1
6
2
8
12
9
11
7 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-62 Install Multi-point Adapters 
5
Install Multi-point Adapters
Multi-p oint ad ap ters are used  to p rovide sig nal fanout of the T-interfac e. Fanout 
c an b e p erformed  at the work station b y the BR851-B or the 367A. These 
ad ap ters sup p ort more than one ISDN terminal p er horizontal 4-p air D-insid e wire 
(DIW). To sup p ort multip le horizontal runs, fanout must be p erformed  in the 
satellite c loset b y a MDF with multip le c ommon rows. The 110RA1-12 p rovid es 
fanout for two horizontal runs and  c ontains the 100 Ohm terminating  resistor. This 
c an b e used  for b asic  multi-p oint or p oint-to-p oint with terminating resistor in the 
c loset. Other fanout b loc ks inc lud e the 110AB1-025M and  the 110AB1-050M.
BR851-B Adapter (T-Adapter)
The BR851-B sup ports two terminals on one multi-p oint BRI at the work station. It 
is a T-shap ed  d evic e used to fanout transmission and  p ower. The BR851-B is an 
8-p in d evic e with a sing le p lug  and  two jac ks. See Fig ure 5-24
.
Figure 5-24. Wiring Diagram of BR851-B Figure Notes
1. Wire Pairs
2. Pin Numb ers
3. Mod ular Plug  (Male)4. Female
5. Two 8-p in Mod ular Jac ks
6. T-Typ e Ad ap ter
3
44
5
11
1
22
2
44 4
RR R
88 8
44 4
TT T
77 7
33 3
RR R
66 6
11 1
TT T
55 5
11 1
RR R
44 4
33 3
TT T
33 3
22 2
RR R
22 2
22 2
TT T
11 16