Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-19 Administer the System 
3
Set Country Options
Certain c ountry options need  to b e set to turn red  failure ind ic ation LEDs off. 
Refer to Ta b l e  3 - 5
 for a list of c ountry c od es.
1. Verify the sc reen d isp lays command:
2. Type change system-parameters country options 
and press 
En te r.
A sc reen similar to Sc reen 3-3 is d isp layed . The c ursor is set on the 
Companding Mode
 line.
Screen 3-3. Typical System Parameters Country-Options Screen  
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-20 Administer the System 
3
3. The d efault c omp and ing  mode is mu-Law. If the c ountry uses A-Law 
c omp and ing , typ e A-Law. Press 
En te r when this information is c orrec t.
Other items eventually need  to b e entered  on this sc reen, b ut this is all that 
must b e d one to turn the red  alarm LEDs off.
4. If all red  LEDs d o not g o off, reseat (unp lug  and  reinsert) any port circuit 
p acks d isp laying  red  LEDs.
!CAUTION:
To avoid a disk c rash, never
 reseat the DEFINITY AUDIX System 
without first shutting  it d own. Shut d own the DEFINITY AUDIX System 
(and  allow the d isk to c omp letely spin d own) b efore unp lugg ing  the 
assemb ly. See 
‘‘ D EFI N I TY A U D I X Sy st e m  Po w e r  Pro c e d u re s’’  o n  
page 3-33 for the p rop er p roc ed ures.
5. If the red  LEDs still d o not g o off, refer to D EFI N I TY En t e rp r i se  
Communic ations Server Release 8 Maintenanc e for R8si
.
NOTE:
Ig nore the red  alarm ind ic ation LED on the TN767 or TN464/2464 
DS1 c irc uit p ac k until after the DS1 c irc uit p ac k is ad ministered . 
Alarms will ap p ear in the Alarm Log  when p ower is ap p lied  to the 
system b efore all eq uip ment c onnec ting  to port c irc uit p ac ks is 
installed . Normally, some alarms will b e log g ed when p ower is 
ap p lied to the system, b ut should  b e resolved  q uic kly. If no 
eq uip ment is c onnec ted  to the p ort c irc uit p ac ks, alarms assoc iated  
with these p orts c an take up  to four hours to log , b ut will c lear 
automatic ally after all equip ment is installed  and op erating  c orrec tly.
Table 3-5. Country Codes
Country Code Country Code
USA 1 France 12
Australia 2 Germany 13
Jap an 3 Czec hoslovakia 14
Italy 4 Russia 15
Netherland s 5 Argentina 16
Sing ap ore 6 Greec e 17
Mexic o 7 China 18
Belg ium 8 Hong  Kong 19
Saud i Arabia 9 Thailand 20
United King d om 10 Maced onia 21
Sp a i n 1 1 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-21 Administer the System 
3
Change Craft Password
The p assword  for the c raft log in must be changed b y the installing  tec hnic ian to 
p revent unauthorized  ad ministration c hang es.
!CAUTION:
After the password is changed, the new password must be safeguarded so 
no unauthorized  ad ministration c hang es c an b e mad e. This p assword  
M U ST N O T B E REVEAL ED  t o  t h e  c u s t o m e r  o r  t o  a n y  u n a u t h o r iz e d  p e r s o n .
Passwords are changed using the Change Password Screen. See Sc reen 3-4.
1. Verify the sc reen d isp lays command:
2. Type change password craft. Press 
En t e r .
Screen 3-4. Typical Change Password Screen 
3. Verify the sc reen d isp lays the Chang e Password  Sc reen. The c ursor is 
p ositioned  on Password for Login Making Change:
”
4. Typ e the p assword  assig ned  to the c raft log in (assig ned  as 
c rftp w when 
system is shipped) and press 
En t e r. The c ursor is p ositioned  on Login’s 
Password
:. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-22 Administer the System 
3
5. Enter new p assword . Valid  p assword s c onsist of a c omb ination of from 
four to eleven alp ha or numeric  c harac ters. At least one letter and  one 
numb er must be used  in eac h password .
6. Press 
En te r. The c ursor is p ositioned  on Reenter Login’s Password
:.
7. Type new password again and press 
EN TER.
8. Verify the sc reen d isp lays:
command successfully completed
command
:
Set Daylight Savings Rules
You c an set up  to 15 c ustomized d aylig ht saving s time rules. If you have switc hes 
in several d ifferent time zones, you c an set up  rules for eac h. A d aylig ht saving s 
time rule sp ec ifies the exac t time when you want to transition to and  from daylig ht 
saving s time. It also spec ifies the inc rement at whic h to transition.
NOTE:
The d efault d aylig ht saving s rule is 0
, no d aylig ht saving s.
1. Type change daylight-savings-rules
 and press 
En t e r. 
2. Type the appropriate start and stop information in the Change Day
, 
Month
, Date
, Time
, and  Increment
 (for example, 1:00
 eq uals one hour) 
field s for eac h rule. 
NOTE:
You c an c hang e any rule exc ep t rule 0 (zero). You c annot delete a 
d aylig ht saving s rule if it is in use on either the Loc ations or Date and 
Ti m e  s c re e n s .
3. Press 
En t e r.
 
DAYLIGHT SAVINGS RULES
Rule Change Day Month___Date Time____Increment
0: No Daylight Savings
1: Start: first Sunday
___ on or after April___ 1  at _2:00 01:00Stop:  first Sunday___ on or after October_ 25 at _2:002: Start: first _________ on or after ________ __ at __:    :  Stop:  first _________ on or after ________ __ at __:__
3: Start: first _________ on or after ________ __ at __:    :  Stop:  first _________ on or after ________ __ at __:__         
4: Start: first _________ on or after ________ __ at __:    :  Stop:  first _________ on or after ________ __ at __:__         
5: Start: first _________ on or after ________ __ at __:    :  Stop:  first _________ on or after ________ __ at __:__         
6: Start: first _________ on or after ________ __ at __:    :  Stop:  first _________ on or after ________ __ at __:__         
7: Start: first _________ on or after ________ __ at __:    :  Stop:  first _________ on or after ________ __ at __:__          
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-23 Administer the System 
3
Set Date and Time
1. Type set time 
and 
press En t e r.
.
Screen 3-5. Typical Date and Time Screen
2. Typ e the d ay of the week in Eng lish (Sunday throug h Saturd ay) and  press 
TA B to move to next field . See Tab le 3-6 for Eng lish day of the week names.
3. The c ursor is p ositioned  on the Month:
 field . Typ e the c urrent month in 
Eng lish (January throug h Dec emb er). See Tab le 3-7
 for English month 
names. After the month is entered, p ress 
TA B to move to next field .
Table 3-6. English Day of the Week Names
Day Number Day Name
1Sunday
2 Mond ay
3Tuesday
4 Wed nesd ay
5Thursday
6Friday
7Saturday
 
                           DATE AND TIME
DATE
 Day of the Week: Tuesday
Month: FebruaryDay of the Month: 8 Year: 2000
TIME
Hour: 20 Minute: 30Second: XX Type: standardDaylight Savings Rule: 0 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-24 Administer the System 
3
4. The c ursor is p ositioned  on the Day of the Month:
 field . Typ e the d ay 
of month (1 through 31) and  p ress 
TA B to move to the next field .
5. The c ursor is p ositioned  on the Year:
 field . Typ e the c urrent year and  
p ress 
Ta b to move to the next field .
6. The c ursor is p ositioned  on the Hour:
 field . Typ e the c urrent hour for a 
24-hour c loc k. See Ta b l e  3 - 8
. Press Ta b to move to the next field .
7. The c ursor is p ositioned  on the Minute:
 field . Type c urrent minute (0 
throug h 59). Sec ond s c annot b e set.
8. Type standard
 or daylight savings
 in the Type
 field .
9. Typ e the rule (numb er) in the Daylight Savings Rule
 field.
10. Press 
En t e r when the information is c orrec t.
Table 3-7. English Month Names
Month Number Month Name
1 January
2February
3March
4April
5May
6 June
7July
8 Aug ust
9 Sep temb er
10 Oc tob er
11 Novemb er
12 Dec ember 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-25 Administer the System 
3
11. Verify the sc reen d isp lays:
command successfully completed
command:
12. Typ e display time
, and  p ress 
En t e r to verify d ate/time d ata.
Table 3-8. Conversion to 24-Hour Clock
Standard Time Standard Time
12-Hour 24-Hour 12-Hour 24-Hour
12:00 
mid nig ht0000 12:00 
noon1200
 1:00 am 0100 1:00 p m 1300
 2:00 am 0200 2:00 p m 1400
 3:00 am 0300 3:00 p m 1500
 4:00 am 0400 4:00 p m 1600
 5:00 am 0500 5:00 p m 1700
 6:00 am 0600 6:00 p m 1800
 7:00 am 0700 7:00 p m 1900
 8:00 am 0800 8:00 p m 2000
 9:00 am 0900 9:00 p m 2100
10:00 am 1000 10:00 p m 2200
11:00 am 1100 11:00 p m 2300 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-26 Administer the Circuit Packs 
3
Administer the Circuit Packs
After the eq uip ment is installed  (inc lud ing  c irc uit p ac ks), the c irc uit pac ks must 
b e ad ministered . Refer to 
DEFINITY Enterp rise Communic ations Server Release 
8 Ad ministration and  Feature Desc rip tion
 for more information.
The following information d esc ribes general ad ministration information:
nUse the Circ uit Pac ks form to ad minister c irc uit p ac ks to c arrier slots. The 
c irc uit p ac ks must b e installed  (or assig ned  using  the Circ uit Pac ks form) 
before administering voice terminals, attendant consoles, or trunks.
nEac h p ag e of the form rep resents one c arrier in the c ab inet shown on the 
c ommand  line. All c arriers and  slots ap p ear even if they are not inc lud ed  
in the hardware.
nIt is not nec essary to fill in the Circ uit Pac ks form if the c irc uit p ac ks are 
installed  at the time of ad ministration.
nRefer to DEFINITY Communic ations System Generic  3 Planning  and 
Config uration
, 555-230-601, for more information ab out c irc uit pac k 
ad ministration and port assig nment rec ord s.
nFor initial installation, assig n c irc uit p ac ks to slots using the hard ware 
configuration layout record from the fac tory or Customer Services 
Org anization. Do not arb itrarily assig n c irc uit p ac ks to slots.
nWhen a c irc uit p ac k in a slot d iffers from what has b een ad ministered on 
the form, a “ #”  d isp lays b etween the “ Sfx”  and  “ Name”  field s.
nAll slot field s are d isp layed .
Administration Commands
Use the following  ad ministration c ommand s to ad minister the Circ uit Pac k form.
NOTE:
If no cabinet number is specified, this command defaults to 1.
Table 3-9. Administration Commands
Action Object Qualifier
1
1.Brackets [ ] indicate the qualifier is optional. Single quotes (’ ’) indicate the 
text inside the quote must be entered exactly as shown or an abbreviated 
form of the word may be entered. xx is the cabinet number.
c hang e c irc uit-p ac ks xx (c ab inet number)
d isp lay circuit-p acksxx (c ab inet number) [ ’p rint’ or ’sc hed ule’] 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-27 Administer the Circuit Packs 
3
Form Instructions
Screen 3-6. Change Circuit-Packs Screen
NOTE:
Each page of the form represents 1 carrier within the cabinet specified on 
the command line. For R8si configurations, all carriers and slots appear 
even if they are not included in the actual hardware. This supports 
reconfiguration.
nCabinet
 — Disp lay-only field . This field  shows the c abinet numb er as 
entered  on the c ommand  line.
nCarrier
 — Disp lay-only field . This field  shows the letter of the c arrier (A 
throug h E) c irc uit p ac ks are b eing  ad ministered  on.
nCarrier Type
 — Disp lay-only field . This field  shows the typ e of c arrier. 
nSlot
 — Disp lay-only field . The slot eq uates to the physic al slot of the g iven 
c arrier; the numb er of slots d isp layed  d ep end s on the system being 
configured.
For R8si c onfig urations, ALL slots that c ould p ossib ly b e ad ministered are 
d isp layed  even if they do not ap p ly to the c urrent c onfig uration of the 
system. This is to ac c ommod ate the situation when a system is b eing  
rec onfig ured .
change circuit-packs                                            Page   1 of   5 
                              CIRCUIT PACKS                                     
        Cabinet: 1                            Carrier: A
                                         Carrier Type: processor        
 Slot Code  Sf Mode   Name
  01: TN758          POOLED MODEM      
  02: TN726  B       DATA LINE         
  03: TN763  D       AUXILIARY TRUNK   
  04: TN750  C       ANNOUNCEMENT      
  05: TN2181         DIGITAL LINE      
  06: TN464  F       DS1 INTERFACE     
  07: TN2138         CO TRUNK          
  08: TN754  B       DIGITAL LINE      
  09: TN799  B       CONTROL-LAN       
  10: TN767  D       DS1 INTERFACE     
 Slot Code  Sf Mode   Name               Slot Code  Sf Mode   Name
                                          11: TN464  F       DS1 INTERFACE     
  01: TN758          POOLED MODEM         12: MEDPRO         RESERVED-IP       
  02: TN726  B       DATA LINE            13: TN802  B       MAPD BOARD        
  03: TN763  D       AUXILIARY TRUNK      14: TN2149         ANALOG LINE       
  04: TN750  C       ANNOUNCEMENT         15: TN754  B       DIGITAL LINE      
  05: TN2181         DIGITAL LINE         16: TN754  B       DIGITAL LINE      
  # indicates circuit pack conflict. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-28 Administer the Circuit Packs 
3
Tab le 3-10 lists the slots to use, and the c irc uit p ac k typ es that may b e 
ad ministered  in those slots, for eac h c omb ination of 
Cab inet/Carrier/Carrier Typ e in a R8si c onfig uration.
nCode
 — Enter the c irc uit p ac k c od e (TN followed  b y a 3- or 4-d ig it 
numb er). If there is a p hysic al c irc uit p ac k installed  in the slot, the entry 
must matc h that of the c irc uit p ac k. If there is eq uip ment ad ministered on 
a slot, the eq uip ment must b e removed  from the c irc uit p ac k b efore the 
c irc uit p ac k c an b e c hang ed  or removed .
nSfx
 — Enter the c irc uit pac k suffix, if ap p lic able.
nName
 — Disp lay-only field. This field  shows the alp hanumeric  name of 
the c irc uit p ac k (suc h as Dig ital Line).
NOTE:
When the circuit pack physically inserted in the slot differs from what has 
been administered on this form, a # displays between the Sfx and Name 
fields.
Implementation Notes
Sc reen 3-6 shows all field s that may b e displayed . The field s that ap p ear on a 
p artic ular sc reen may vary d ep end ing  up on the system c onfig uration b eing  
ad ministered .
The number of slot fields displayed may vary depending on the system being 
config ured . For R8si configurations, all p ossib le slots d isp lay.
Table 3-10. Circuit Pack Cabinet Layout
Cabinet Layout Carrier TypeUse 
Slots Circuit Pack Types
1A (SCC Basic  Control Cab inet) p roc essor 01-10 All port c irc uit p ac ks
1A (SCC Enhanc ed Control Cab inet) p roc essor 01-16 All port c irc uit p ac ks
1B (SCC Dup lic ated  Control Cab inet) p roc essor 01-10 All port c irc uit p ac ks
1B, C, D (SCC Port Cab inet) p ort 01-18 All port c irc uit p ac ks
2A & 3A (SCC Exp ansion Control 
Cab inet)exp ansion-c ontrol 01 TN570, TN776
02-17 All p ort c irc uit p ac ks
2B, C, D (SCC Port Cab inet)
3B, C, Dp ort 01-18 All p ort c irc uit p ac ks