Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-83 Add DCS Interface 
5
Install Cables
1. Install c ab le from the c ab inet to a hub  or Internet Protoc ol (IP) Switc h as 
req uired. Connec t the 259A c onnec tor to the p ort slot c ontaining the 
C-LAN c irc uit p ac k. See Fig ure 5-29
. For a p inout of TN799, see Ta b l e  
5-25. 
Figure 5-29. Cable Connection for C-LAN Figure Notes
1. 259A Connec tor
2. DW8A Cab le3. Hub  or IP Switc h
1
2
3cydflan2  EWS 101398 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-84 Add DCS Interface 
5
Enter Added Translations
1. Get the DOSS order numb er of the upg rad e. Call the reg ional CSA to 
p erform the step s in this sec tion.
2. To enab le DCS, set the DCS
 field  on the System Parameters-Customer 
Options form to y
.
3. Ad minister the other req uired  translation data using  the forms listed  und er 
Distrib uted  Communic ations System (DCS) in 
DEFINITY Communic ations 
System Generic  4 V4 Imp lementation
.
Save Translations
1. If the system is hig h- or c ritic al-reliab ility, typ e status spe
 and press En te r  
to verify that the stand b y SPE is refreshed  and  that the stand b y d isk is in 
servic e.
2. Type save translation [spe-a or both] disk
 and press 
En te r. This 
c ommand  instruc ts the system to take all translation information in 
memory and  write it to the d isk(s).
Table 5-25. TN799 Pinout
Backplane Pin 25-Pair Wire Color Lead NamePeripheral 
Connector Pin
103 White/Orang e TD+ 27
003 Orang e/White TD- 2
104 White/Green RD+ 28
004 Green/White RD- 3 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-85 Add ISDN — PRI 
5
Add ISDN — PRI
North American
1. Use a TN767E (or later) DS1 or a TN464F DS1/E1 c irc uit p ac k for a 
sig naling  link and  up  to 23 ISDN — PRI Trunk Group members. 
2. Install a Tone-Cloc k c irc uit p ac k to p rovid e sync hronization for the DS1 
circuit pack. 
3. If using  a TN464F, then p ac ket b us sup p ort has not b een ad d ed , req uiring  
greater than 4 PRI signaling groups, see ‘‘Add Packet Bus Support to 
R8si’’ on page 5-87 for installation of ad d itional c irc uit p ac ks for p ac ket 
bus support.
As an op tion to the TN768 or TN2182B Tone-Cloc k, a TN780 Tone-Cloc k 
(installed  in the PPN) c an interfac e external Stratum 3 sync hronization for DS1.
International
1. Install a TN464C (or later) DS1/E1 c irc uit p ac k for the assig nment of the 2 
sig naling  c hannels and  up  to 30 ISDN — PRI Trunk Group  memb ers. Eac h 
E1 sp an p rovid es 32 p orts. 
2. Install a Tone-Cloc k c irc uit pac k to p rovid e sync hronization for the DS1/E1 
circuit pack.
3. If packet bus support has not been added and greater than 8 PRI 
sig naling  g roups are req uired , see ‘‘Ad d Pac ket Bus Sup p ort to R8si’’ on 
page 5-87 for installation of ad d itional c irc uit p ac ks for p ac ket b us 
support.
As an op tion to the TN2182B Tone-Cloc k, a TN780 Tone-Cloc k (installed  in the 
PPN) can interface external Stratum 3 sync hronization for DS1.
Service Interruption
If packet bus support for R8si must be added and TN750s must be installed as 
p art of that sup p ort, then add ing  ISDN — PRI req uires a servic e interruption. 
Notify the c ustomer in ad vanc e as to when the ad d ition will b e c arried  out. See 
‘‘Add Packet Bus Support to R8si’’ on page 5-87
 for further information.
Add Packet Bus Support
If p ac ket b us sup p ort is not alread y installed , see ‘‘Ad d  Pac ket Bus Supp ort to 
R8si’’ on page 5-87 and  p erform the step s. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-86 Add ISDN — PRI 
5
Add Circuit Packs
1. Determine port assig nment of c irc uit p ac ks to be ad d ed .
2. Install the DS1 Interfac e c irc uit p ac k in the assig ned c arrier slot.
3. Install a TN748B (or later) (or the international TN420B/C) Tone Detec tor 
circuit pack if required.
Install Cables
1. Install c ab les from c ab inet to MDF as req uired .
Enter Added Translations
1.Ad minister the forms listed  und er “ Integ rated  Servic es Dig ital Network — 
Primary Rate Interfac e”  in 
DEFINITY Enterp rise Communic ations Server 
Release 8 Ad ministrator’s Guid e
.
Resolve Alarms
1. Examine the alarm log. Resolve any alarms that may exist using  D EFI N I TY 
Enterp rise Communic ations Server Release 8 Maintenanc e for R8si
. 
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard s.
3. Up d ate b ac kup  c ard s, if nec essary. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-87 Add Packet Bus Support to R8si 
5
Add Packet Bus Support to R8si
Standard Reliability R8si System
Service Interruption
Installing  TN570 Exp ansion Interfac e c irc uit pac ks as part of ad d ing  p ac ket b us 
sup p ort req uires a servic e interrup tion. Notify the c ustomer in ad vanc e as to 
when the ad d ition will b e c arried  out. If not installing  TN570 c irc uit p ac ks, then 
servic e is not interrup ted  and  you c an skip  to the Install Circ uit Pac ks sec tion.
Set Offer Category and Activate Offer
1. Type change system-parameters offer
 and press En t e r.
2. Set the Offer Category
 field  to A
, if not alread y set.
3. Set the Activate Offer
 field  to y
. 
Disable Alarm Origination
1. Type change system-parameters maintenance
 and press En t e r. 
2. Set the Alarm Origination Activated
 field  to n
.
!CAUTION:
If you d o not d isab le Alarm Orig ination, the system may g enerate 
alarms, resulting  in unnec essary troub le tic kets. 
3. For some releases of software, disab le Cleared Alarm Notification
 
and  Restart Notification
 b efore sub mitting  the form.
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard .
3. If the system c ontains a TN750/B Announc ement c irc uit p ac k, type 
display announcements
 and  p ress 
En t e r. If ad ministered  rec orded  
announc ements are listed , typ e list configuration software-version long
 
and  p ress 
En t e r. To save the announc ements, typ e save announcements
 
and  p ress 
En t e r. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-88 Add Packet Bus Support to R8si 
5
Power Down Cabinet 
1. At the PPN, set the main c irc uit b reaker to OFF.
2. At an EPN, set the main c irc uit b reaker to OFF.
Install Circuit Packs
1. Install the ap p rop riate c irc uit pac ks. See Tab le 5-26.
Power Up System
1. At the EPN, set the main c irc uit b reaker to ON.
2. At the PPN, set the main c irc uit b reaker to ON.
3. The system p erforms a level 4 reb oot, load ing  the system translations from 
the translation c ard s. Reb ooting  takes ab out 10 minutes.
4. After all troub le is c leared , verify the EMERGENCY TRANSFER CONTROL 
switc h is set to AUTO. This restores the system to the normal mod e.
Test the Packet Bus and C-LAN Circuit Pack
1. Type test packet port-network 1 long 
and p ress En t e r. For more d etail 
ab out these tests, refer to the test p kt c ommand  sec tion in the 
maintenanc e b ook. 
Resolve Alarms
1. Examine the alarm log . Resolve any alarms using  DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8si
. 
Table 5-26. Circuit Pack Locations for Packet Bus in R8 PPN
Circuit Pack Carrier Quantity Slot
TN570 Control Carrier A 1 or 2
1
1. Quantity of this p ack should  equal the numb er of EPNs.
EXPN INTFC/1 and  /2
TN771C Control Carrier A 1
2
2. Op tional for d ig ital trunk testing .
Any Availab le Port Slot 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-89 Add Packet Bus Support to R8si 
5
Enable Customer Options and Alarm Origination
1. Get the DOSS order numb er of the upg rad e and  c all the reg ional CSA to 
p erform the step s in this sec tion.
2. To use Ac cess Security Gateway (ASG), see Appendix D, ‘‘Access 
Sec urity Gateway’’.
3. Type change system-parameters customer-options
 and press 
En te r. 
Use these forms to verify the c ustomer op tions are p roperly set.
NOTE:
If the c ustomer was using  Sup p lementary Servic es Protoc ol “ b ”  or 
“ d”  on an ISDN-PRI trunk g roup  b efore the up g rad e, set the Basic 
Call Setup 
field  on the QSIG Op tional Features p ag e to y
.
4. Be sure the system is p art of the existing  INADS d atab ase b y c alling  the 
INADS Datab ase Administrator at the Tec hnic al Servic e Center (TSC). 
Verify that INADS c an d ial into the system and  that the system c an d ial out 
to INADS. 
As p art of the system reg istration proc ess, the INADS Datab ase 
Ad ministrator enab les Alarm Orig ination and  c ustomer op tions.
!CAUTION:
If you d o not enab le Alarm Orig ination when the c ustomer has p urc hased  a 
servic es c ontrac t, the system c annot rep ort any alarm to the TSC 
automatic ally, c ausing the TSC to b e unab le to fulfill the servic es c ontrac t.
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard s.
3. If the system c ontains a TN750/B/C Announc ement c irc uit pac k, typ e 
restore announcements
 and press 
En t e r.
4. Up d ate b ac kup  c ard s, if nec essary. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-90 Add Packet Bus Support to R8si 
5
High or Critical Reliability R8si System
Service Interruption
If no TN570 Exp ansion Interfac e c irc uit p ac ks need  to b e installed  for PktBus 
sup p ort, skip  to and p erform only the Install Circ uit Pac ks sec tion. This 
p roc ed ure d oes not interrup t servic e in this c ase.
Set Offer Category and Activate Offer
1. Type change system-parameters offer
 and press En t e r.
2. Set the Offer Category
 field  to A
, if not alread y set.
3. Set the Activate Offer
 field  to y
. 
Disable Alarm Origination
1. Type change system-parameters maintenance
 and press En t e r. 
2. Set the Alarm Origination Activated to OSS Numbers 
field to n
.
!CAUTION:
If you d o not d isab le Alarm Orig ination, the system may g enerate 
alarms, resulting  in unnec essary troub le tic kets. 
3. For some releases of software, disab le Cleared Alarm Notification
 
and  Restart Notification
 b efore sub mitting  the form.
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard s.
3. If the system c ontains a TN750/B Announc ement c irc uit p ac k, type 
display announcements
 and  p ress 
En t e r. If ad ministered  rec orded  
announc ements are listed , typ e list configuration software-version long
 
and  p ress 
En t e r. To save the announc ements, typ e save announcements
 
and  p ress 
En t e r.
Power Down Cabinet (Standby Cabinet)
1. At the PPN, set the main c irc uit b reaker to OFF.
2. At an EPN, set the main c irc uit b reaker to OFF. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-91 Add Packet Bus Support to R8si 
5
Install Circuit Packs
1. Install the ap p rop riate c irc uit pac ks. See Tab le 5-27.
Power Up System
1. At the EPN, set the main c irc uit b reaker to ON.
2. At the PPN, set the main c irc uit b reaker to ON.
3. The system p erforms a level 4 reb oot, load ing  the system translations from 
the translation c ard s. Reb ooting  takes ab out 10 minutes.
4. After all troub le is c leared , verify the EMERGENCY TRANSFER CONTROL 
switc h is set to AUTO. This restores the system to the normal mod e.
Test the Packet Bus and C-LAN Circuit Pack
1. Type test packet port-network 1 long 
and p ress En t e r. For more d etail 
ab out these tests, refer to the “ test p kt c ommand ”  sec tion in the 
DEFINITY 
Enterp rise Communic ations Server Release 8 Maintenanc e for R8si
. 
Resolve Alarms
1. Examine the alarm log. Resolve any alarms that may exist using  D EFI N I TY 
Enterp rise Communic ations Server Release 8 Maintenanc e for R8si.
 
Table 5-27. Circuit Pack Locations for Packet Bus in PPN
Circuit Pack Carrier Quantity Slot
TN570 Control Carrier A 1 or 2
1
1. Quantity of this p ack should  equal the numb er of EPNs.EXPN INTFC/1 and  /2
Control Carrier B 1 or 2 EXPN INTFC/1 and  /2
TN771C Control Carrier A 1
2
2. Req uired  for critic al-reliab ility EPNs and PPN. Optional for d ig ital trunk testing  in
hig h-reliab ility PPN.
Any Availab le Port Slot 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-92 Add Packet Bus Support to R8si 
5
Enable Customer Options and Alarm Origination
1. Get the DOSS order numb er of the upg rad e. Call the reg ional CSA to 
p erform the step s in this sec tion.
2. To use Ac cess Security Gateway (ASG), see Appendix D, ‘‘Access 
Sec urity Gateway’’.
3. Type change system-parameters customer-options
 and press 
En te r. 
Use these forms to verify the c ustomer op tions are p roperly set.
NOTE:
If the c ustomer was using  Sup p lementary Servic es Protoc ol “ b ”  or 
“ d”  on an ISDN-PRI trunk g roup  b efore the up g rad e, set the Basic 
Call Setup 
field  on the QSIG Op tional Features p ag e to y
.
4. Be sure the system is p art of the existing  INADS d atab ase b y c alling  the 
INADS Datab ase Administrator at the Tec hnic al Servic e Center (TSC). 
Verify that INADS c an d ial into the system and  that the system c an d ial out 
to INADS. 
As p art of the system reg istration proc ess, the INADS Datab ase 
Ad ministrator enab les Alarm Orig ination and  c ustomer op tions.
!CAUTION:
If you d o not enab le Alarm Orig ination when the c ustomer has p urc hased  a 
servic es c ontrac t, the system c annot rep ort any alarm to the TSC 
automatic ally, c ausing the TSC to b e unab le to fulfill the servic es c ontrac t.
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard s.
3. If the system c ontains a TN750/B/C Announc ement c irc uit pac k, typ e 
restore announcements
 and press 
En t e r.
4. Up d ate b ac kup  c ard s, if nec essary.