Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							555-233-120
Comcode 108678699
Issue 1
April 2000
DEFINITY®
Enterprise Communications Server
Release 8.2
Installation and Test for Single-Carrier Cabinets 
						

							Copyright 
Ó 2000, Lucent Technologies
All Rights Reserved
Printed in U.S.A.
Notice
Every effort was made to ensure that the information in this book was 
complete and accurate at the time of printing. However, information is 
subject to change.
Your Responsibility for Your System’s Security
Toll fraud is the unauthorized use of your telecommunications system 
by an unauthorized party, for example, persons other than your com-
pany’s employees, agents, subcontractors, or persons working on your 
company’s behalf. Note that there may be a risk of toll fraud associated 
with your telecommunications system and, if toll fraud occurs, it can 
result in substantial additional charges for your telecommunications 
services.
You and your system manager are responsible for the security of your 
system, such as programming and configuring your equipment to pre-
vent unauthorized use. The system manager is also responsible for 
reading all installation, instruction, and system administration docu-
ments provided with this product in order to fully understand the fea-
tures that can introduce risk of toll fraud and the steps that can be taken 
to reduce that risk. Lucent Technologies does not warrant that this 
product is immune from or will prevent unauthorized use of com-
mon-carrier telecommunication services or facilities accessed through 
or connected to it. Lucent Technologies will not be responsible for any 
charges that result from such unauthorized use.
Lucent Technologies Fraud Intervention
If you suspect that you are being victimized by toll fraud and you need 
technical support or assistance, call Technical Service Center Toll 
Fraud Intervention Hotline at 1 800 643-2353 or contact your local 
Lucent representative.
Federal Communications Commission Statement
Part 15: Class A Statement. This equipment has been tested and 
found to comply with the limits for a Class A digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment generates, 
uses, and can radiate radio-frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a resi-
dential area is likely to cause harmful interference, in which case the 
user will be required to correct the interference at his own expense.
Part 68: Network Registration Number. This equipment is registered 
with the FCC in accordance with Part 68 of the FCC Rules. It is identi-
fied by FCC registration number AS593M-13283-MF-E.
Part 68: Answer-Supervision Signaling. Allowing this equipment to 
be operated in a manner that does not provide proper answer-supervi-
sion signaling is in violation of Part 68 Rules. This equipment returns 
answer-supervision signals to the public switched network when:
• Answered by the called station
• Answered by the attendant
• Routed to a recorded announcement that can be administered by 
the CPE user
This equipment returns answer-supervision signals on all DID calls 
forwarded back to the public switched telephone network. Permissible 
exceptions are: 
• A call is unanswered
• A busy tone is received
• A reorder tone is receivedCanadian Department of Communications (DOC)
Interference Information
This digital apparatus does not exceed the Class A limits for radio 
noise emissions set out in the radio interference regulations of the 
Canadian Department of Communications.
Le Présent Appareil Nom
érique n’émet pas de bruits radio
électriques 
d
épassant les limites applicables aux appareils num
ériques de la class 
A pr
éscrites dans le reglement sur le brouillage radio
électrique 
édict
é 
par le minist
ére des Communications du Canada.
Trademarks
See the preface of this document.
Ordering Information
Call: Lucent Technologies BCS Publications Center
Voice 1 800 457-1235   International Voice 317 322-6416
Fax 1 800 457-1764      International Fax 317 322-6699
Write: Lucent Technologies BCS Publications Center
2855 N. Franklin Road
Indianapolis, IN 46219
Order: Document No. 555-233-120
Comcode 108678699 
1, April 2000
For additional documents, refer to the section in “About This Docu-
ment” entitled “Related Resources.” 
You can be placed on a standing order list for this and other documents 
you may need. Standing order will enable you to automatically receive 
updated versions of individual documents or document sets, billed to 
account information that you provide. For more information on stand-
ing orders, or to be put on a list to receive future issues of this docu-
ment, contact the Lucent Technologies Publications Center.
European Union Declaration of Conformity
The “CE” mark affixed to the DEFINITY® equipment described in 
this book indicates that the equipment conforms to the following Euro-
pean Union (EU) Directives:
• Electromagnetic Compatibility (89/336/EEC)
• Low Voltage (73/23/EEC)
• Telecommunications Terminal Equipment (TTE) i-CTR3 BRI 
and i-CTR4 PRI
For more information on standards compliance, contact your local dis-
tributor.
Comments
To comment on this document, return the comment card at the front of 
the document.
Acknowledgment
This document was prepared by Product Documentation Development, 
Lucent Technologies, Denver, CO. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Contents 
iii  
Contents
Contents iii
About This Book ix
nRelated Documentsx
nHow to Order Documentationx
nHow to Comment on This Documentxi
nTrademarksxi
nStandards Compliancexii
nLASER Productxiii
nElectromagnetic Compatibility Standardsxiii
nSecurity Issuesxiv
nWhere to Call for Technical Supportxv
nAntistatic Protectionxv
nRemove/Install Circuit Packsxvi
nFederal Communications Commission Statementxvi
1 Install and Connect the Cabinets 1-1
nCheck Circuit Packs1-1
nCheck Customer’s Order1-1
nHow to Correct Shipping Errors1-2
nUnpack and Inspect1-2
nInstall Single-Carrier Cabinets1-2
nApproved Grounds1-5
nConnect Cabinet Grounds1-6
nConnect AC Power1-13
nConnect DC Power1-14
nConnect Battery Cabinet1-18
nConnect Optional Battery Leads1-19
nConnect AC Power to Stratum 3 Clock Cabinet1-20
nConnect DC Power and Ground to
Stratum 3 Clock Cabinet1-20
nConnect Time Division Multiplexing Bus Cables1-21
nVerify Port Cabinet Address Plugs1-26
nInstall Rear Panels1-27 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Contents 
iv  
nInstall Ground Plates1-28
nConnect System Cables1-31
nInstall Earthquake Protection1-37
2 Install Telecommunications Cabling 2-1
nEquipment Room Hardware2-1
nMain Distribution Frame2-4
nInstallation Requirements2-5
nInstall Equipment and Cables2-7
nInstall Sneak Fuse Panels2-8
nInstall Coupled Bonding Conductor2-11
nLabel the Main Distribution Frame2-13
3 Accessing and Activating the System 3-1
nAccess the System3-2
nActivate the System3-13
nScreens and Commands3-16
nAdminister the System3-17
nAdminister the Circuit Packs3-26
nSet System Maintenance Parameters3-29
nAdminister Attendant Console3-30
nSave Translations3-30
nInstallation Completion3-32
nDEFINITY AUDIX System Power Procedures3-33
4 Test the System 4-1
nCheck System Status for Each Cabinet4-2
nCheck Circuit Pack Configuration4-4
nTest Time Division Multiplexing Bus
in Processor Port Network4-5
nTest Tone-Clock Boards4-6
nTest Expansion Interface Circuit Packs4-7
nTest Time Division Multiplexing Bus
for Each Expansion Port Network4-8
nTest Tone-Clock for Each Expansion Port Network4-9
nTest Tone-Clock Interchange for Each
Expansion Port Network4-9
nTest Expansion Interface Exchange for
Each Expansion Port Network4-10 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Contents 
v  
nCheck Circuit Pack Configuration4-11
nSave Translations, if Required4-11
nNext Steps4-12
5 Install and Wire Telephones and
Other Equipment 5-1
nVoice and Data Terminals5-1
nTelephone Connection Example5-1
nAnalog Station or 2-Wire Digital Station Example5-4
nAnalog Tie Trunk Example5-5
nDigital Tie Trunk Example5-6
nDS1 Tie Trunk Example5-7
nAuxiliary Connector Outputs5-9
nThree-Pair and Four-Pair Modularity5-11
nAdjunct Power Connections5-15
nAttendant Console5-17
nInstall 26B1 Selector Console5-18
nConnect External Alarm Indicators5-18
nInstall Remote Network Interface5-19
nInstall Off-Premises Station Wiring5-21
nInstall Off-Premises or Out-of-Building Stations5-22
nInstall Emergency Transfer Units and
Associated Telephones5-28
nInstall External Ringing5-37
nInstall Queue Warning Indicator5-37
nInstall Adjuncts and Peripherals5-37
nInstall the 1145B Power Supply5-38
n1151A1 and 1151A2 Power Supplies5-47
nCAMA/E911 Installation5-50
nInstall the BRI Terminating Resistor5-58
nInstall Multi-point Adapters5-62
nConnect Stratum 3 Clock5-65
nDEFINITY Wireless Business System5-71
nCellular Business System5-71
nForum PCM5-71
nConnect Modem to Telephone Network5-72
nAdd Circuit Packs5-75 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Contents 
vi  
nList of Circuit Packs5-76
nAdd DCS Interface5-81
nAdd ISDN — PRI5-85
nAdd Packet Bus Support to R8si5-87
nAdd CallVisor ASAI5-93
nAdd ISDN—BRI5-95
nAdd IP Interface Assembly5-96
nInstalling an Integrated Channel
Service Unit (ICSU) Module5-129
nInstalling a 3150/3170 Channel Service Unit5-133
nConnector and Cable Diagrams (Pinout Charts)5-135
6 Test Telephones and Other Equipment 6-1
nMake Test Calls 6-2
nTest 302C Attendant Console6-2
nTest External Ringing6-3
nTest Queue Warning Indicator6-3
nTest Integrated Announcement6-3
nTest Music-on-Hold6-4
nTest Emergency Transfer6-4
nTest Remote Access Interface6-4
nTest Basic Rate Interface6-5
nTest C-LAN Board6-5
A Option Switch Settings A-1
nData Module Option Switch SettingsA-1
n7400D Data Module Option SettingsA-3
nAdd Pooled ModemA-5
nPrinter Option SettingsA-8
nCall Detail Recording Option SettingsA-11
nAUDIX Interface Option SettingsA-11
nTN760D Tie Trunk Circuit Pack Option SettingsA-12
nTN464/2464 Option SettingsA-15 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Contents 
vii  
B Connecting and Handling Fiber Optic Cables B-1
nLASER ProductB-1
nOptical Cross-Connect HardwareB-2
nLabels for Fiber Optic CablesB-8
nCleaning Fiber Optic CablesB-8
C Connector and Cable Diagrams C-1
D Access Security Gateway D-1
nUsing the ASG MobileD-2
E UPS Installation for SCC EPN
A-Carrier Cabinet E-1
nParts ListE-2
nConnect the UPSE-2
nWire the 700A8 PlugE-3
nMake the Remaining ConnectionsE-4
nAdminister the EDAE-8
nLoad Test and Verify AlarmsE-9
GL Glossary and Abbreviations GL-1
IN Index IN-1 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Contents 
viii   
						

							About This Book 
ix  
DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
About This Book
This d oc ument p rovid es p roc ed ures and information for installing  and  initially 
testing  the DEFINITY® Release 8.2si and  Release 8.2si with memory system 
configurations. This document also provides information on power and 
p erip heral eq uip ment that c onnec ts d irec tly to a system. 
This d oc ument c overs information related  to DEFINITY ECS Release 8.2. For 
d etails about c hanges for Release 8.2, refer to 
DEFINITY Enterp rise 
Communic ations Server Release 8.2, Chang e Desc rip tion.
The following c onventions d esc rib e the systems referred  to in this d oc ument.
nTh e  w o rd  system, is a g eneral term enc omp assing  Release 8.2 and  
inc lud es referenc es to the DEFINITY Enterp rise Communic ations Server.
nDEFINITY Systems are called: Release 8; Release 8si +  memory; and 
Release 8si.
nAll oc c urrenc es of Release 8si, and  Release 8si +  memory are c alled  
Release 8si unless a sp ec ific  c onfig uration is req uired  to differentiate 
b etween p rod uc t offerings.
nInformation in this d oc ument is ap p lic ab le for Release 5 throug h Release 
8, unless otherwise sp ec ified .
nDEFINITY Enterp rise Communic ations Server is ab b reviated  DEFINITY 
EC S.
nAll p hysic al d imensions in this b ook are in Eng lish (foot p ound  sec ond ) 
(FPS) followed  b y metric  (c entimeter g rams sec ond) (CGS) in p arenthesis. 
Wire g auge measurements are in AWG followed  b y the d iameter in 
millimeters in p arenthesis. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
About This Book 
x Related Documents 
Related Documents
The following doc uments are useful for system-related  information:
nDEFINITY Enterp rise Communic ations Server Release 8 Ad ministration for 
Network Connec tivity
nDEFINITY Enterp rise Communic ations Server Release 8 System 
Desc rip tion
nDEFINITY Enterp rise Communic ations Server Release 8 Maintenanc e for 
R8 r
nDEFINITY Enterp rise Communic ations Server Release 8 Maintenanc e for 
R8 s i
nAT&T Network and  Data Connec tivity Referenc e
nBCS Prod uc ts Sec urity Hand b ook
nDEFINITY Wireless Business System Users Guid e
nDEFINITY Wireless Business System Installation and  Test Guid e
nDEFINITY Wireless Business Systems System Interfac e
nDEFINITY Enterp rise Communic ations Server Release 8 Installation and  
Test for Multic arrier Cabinets
nDEFINITY Enterp rise Communic ations Server Release 8 Ad ministrator’s 
Guid e
nDEFINITY Enterp rise Communic ations Server Release 8 Up g rad es and  
Ad d itions for R8si
nDEFINITY Enterp rise Communic ations Server Release 8 Up g rad es and  
Ad d itions for R8r
nDEFINITY Enterp rise Communic ations Server Release 8 Installation for 
Ad junc ts and  Perip herals
How to Order Documentation
In ad d ition to this book, other d esc rip tion, installation and  test, maintenanc e, and  
ad ministration d oc uments are availab le. A c omp lete list of DEFINITY d oc uments 
c an b e found  in the 
Business Communic ations System Pub lic ations Catalog.
This d oc ument and  any other DEFINITY d oc umentation c an b e ord ered  d irec tly 
from the Luc ent Tec hnolog ies Business Communic ations System Pub lic ations 
Fulfillment Center at 1-317-322-6791 or toll free at 1-800-457-1235.