Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							Option Switch Settings 
A-1 Data Module Option Switch Settings 
A
DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
A
Option Switch Settings
Some of the interfac e units used  b etween the system and other typ es of 
eq uip ment require spec ific  op tion switc h settings for eac h ap p lic ation. This 
sec tion lists the setting s req uired for d ata mod ules, mod ems, printers, and  so 
forth. Refer to the user’s g uid e for eac h typ e of eq uip ment for information on how 
to loc ate and  set the option switc hes. 
Data Module Option Switch Settings
DCS Switch Settings
The Distributed  Communic ations System (DCS) for a system is sometimes 
c onnec ted  to the system throug h the TN790B Proc essor Interfac e c irc uit p ac k or 
a TN794 Network Control/Pac ket Interfac e (Net/Pkt) c irc uit p ac k. The first c irc uit 
c an b e c onnec ted direc tly to the DCS throug h the p roc essor interfac e (PI) 
c onnec tor on the rear of the c ontrol c arrier.
Any of the remaining three c irc uits on the proc essor interfac e used  to sup p ort the 
Distrib uted  Communic ations System (DCS) must b e c onnec ted  throug h a d ata 
mod ule serving  as the interfac e link. The op tion setting s for a 7400A Data Mod ule 
are shown in Ta b l e  A - 1
. Refer to Fi g u re  A - 1 for the loc ation of the switc hes.
NOTE:
The options for the 7400A and  7400C Data Mod ules are set from the front 
p anel interfac e. For the 7400A, refer to 
7400A Data Mod ule User’s Manual, 
555-020-706. For the 7400C, refer to 
DEFINITY Communic ations System 
Hig h Sp eed  Link User’s Guid e
, 555-020-711. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-2 Data Module Option Switch Settings 
A
Figure A-1. DIP Switch Locations
1. Remove the top  c over from the data mod ule. Refer to Chap ter 5, ‘‘Install 
and  Wire Telep hones and  Other Eq uip ment’’.
2. Switc hes 1, 5, and 8 are the only switches to be set. Refer to Ta b l e  A - 1
 for 
the op tion switc h settings. 
Figure Notes
1. Data Mod ule (7400A Shown) 2. DIP Switc h
Table A-1. Data Module Option Switch Settings
DIP Switch Function  Setting
1With Phone
Without PhoneON
OFF
5 Data Metering  
No Data MeteringON
OFF
8 Make Busy on Loc  Loop
No Make Busy on Loc  LoopON
OFF
2, 3, 4, 6, and  7 OFF
1
2
DTE
PO WER
TESTDATA
METERING
7400B Data Mod ule
AA CD RD SD TR OHCHECK
SPEED
DATA
12345678
O
N 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-3 7400D Data Module Option Settings 
A
7400D Data Module Option Settings
The op tion setting s shown in Ta b l e  A - 2 are for the Answer Only interfac e and  are 
set from the front panel interfac e. Set only the d esired  sp eed  of the 7400D. All 
other d efault settings c an b e used .
Refer to “ Set 7400 D”  Op tions on p ag e B-4 to set the sp eed . 
NOTE:
It is rec ommended  that CI and  CH b e set to ON, and  DCD and  DSR b e set 
to normal. This allows log in information to b e d isp layed  on the sc reen 
without having  to send  a c arriage return c harac ter.
Table A-2. 7400 Series Data Module Options (Answer Only Interface)
Set Option Display Abbreviation Possible Values Default
Set  30 0  SPEED ? 3 00 O N ,  O FF ON
Set  12 0 0 SPEED ? 1 20 0 O N ,  O FF ON
Set  24 0 0 SPEED ? 2 40 0 O N ,  O FF ON
Set  48 0 0 SPEED ? 4 80 0 O N ,  O FF ON
Set  96 0 0 SPEED ? 9 60 0 O N ,  O FF ON
Set 19200 SPEED? 19200 ON, OFF ON
Set  A N SWER? A N S A U TO,  MA N U A L AU TO
Set CI LEAD? CI ON, OFF OFF
Set CH LEAD? CH ON, OFF OFF
Set CTS LEAD? CTS NORMAL, ON ON
Set DCD LEAD? DCD NORMAL, ON ON
Set  D SR L EA D ? D SR N ORMA L ,  O N ON
Set DTR DETECT? DTR 0, 10, 20, 30, 50, 100 MSEC 50
Set DTR LEAD? DTR EIA STANDARD, IGNORE EIA STANDARD
Set LL LEAD? LL ON, OFF OFF
Set REMOTE LOOP? REMLOOP GRANT, DENY GRANT
Set RI LEAD? RI CYCLE, ON ON
Set RL LEAD? RL ON, OFF OFF
Set  SIG LS D I SC ? SI GL S D I SC O N ,  O FF ON
Set  TI M IN G? TI MI N G I N TERN A L,  EXTERN A L IN T
Se t  TM  L EA D ? TM O N ,  O FF O FF 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-4 7400D Data Module Option Settings 
A
Set 7400D Options
The following step s are an examp le of how to c hang e the d efault setting  of 9600 
to the c ustom setting  of 19200.
NOTE:
If the link is b etween a Release 8r and  a CMS, set the 7400D to 19200. If 
the link is b etween any other system and  a CMS, leave the sp eed  of the 
7400D set at 9600.
1. From the HOME sc reen, p ress NEXT/NO
 until SET OPTIONS ?
 is 
d isp layed .
2. Press ENTER/YES
 to stay in the SET OPTIONS ?
 menu.
3. Press NEXT/NO
 until SET 9600 SPEED ?
 is d isp layed .
4. Press ENTER/YES
 when SET 9600 SPEED ?
 is displayed.
5. Press NEXT/NO
 when 9600 = ON ?
 is d isp layed .
6. Press ENTER/YES
 when 9600 -> OFF ?
 is displayed.
7. Press ENTER/YES
 when CONTINUE ?
 is d isp layed .
8. Press ENTER/YES
 when SET 19200 SPEED ?
 is displayed.
9. Press NEXT/NO
 when 19200 = OFF ?
 is d isp layed .
10. Press ENTER/YES
 when 19200 -> ON ?
 is displayed.
11. Press NEXT/NO
 when CONTINUE ?
 is d isp layed .
12. Press ENTER/YES
 when 19200 -> ON ?
 is displayed.
13. Press ENTER/YES
 when SAVE CHANGES ?
 is displayed.
NOTE:
Th e  SET OPTIONS ?
 menu c annot b e terminated  if all sp eed s are 
set to off. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-5 Add Pooled Modem 
A
Add Pooled Modem
Mod em Pooling  sup p orts 2 types of c onversion resourc es: integrated  and  
combined. 
The integrated type requires a TN758 Pooled Modem circuit pack for each 2 
c onversion resourc es p rovid ed.
The c omb ined  typ e requires a p ort on a TN754B Dig ital Line c irc uit p ac k and  a 
p ort on either an 8-p ort TN742, TN769; a 16-p ort TN746B; or a 24-port TN793/B, 
TN2793/B Analog  Line c irc uit p ac k for eac h c onversion resourc e p rovid ed.
The p ooled  mod em req uires a Luc ent WP90110 L7
 power supply. Although an 
integ rated  c onversion resourc e c an use either the L5 or L7, the c ombined only 
works with an L7.
!CAUTION:
The L5 and  L7 p ower supp lies look id entic al. Chec k the list numb er on the 
power supply before installing.
1. Determine the p ort assig nment of the c irc uit p ac ks to b e ad d ed  (if 
req uired ).
2. Install the ap p rop riate c irc uit pac ks in assigned  c arrier slot (if req uired ).
3. For Paradyne 3800 Series mod ems:
a. Type AT&F&D2&S4\D3S2=128x7V2S7=60S85=1
 and  p ress 
En te r. 
b. Type ATY0S10=100S78=2M0E0\N1&W
 and  p ress 
En t e r.
4.For other typ es of mod ems, refer to the vend or’s d oc umentation. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-6 Add Pooled Modem 
A
Settings for Modem Connected to Data Module
1. Type add data-module next
 and press En t e r.
2. Type pdm
 in the Type
 field .
3. Type x
 in the Port
 field.
4. Type dte
 in the Connected to
 field and press 
En te r.
5. Type add station next
 and press 
En t e r.
6. Type 2500
 in the Type
 field.
7. Type x
 in the Port
 field.
8. Type n
 in the Tests
 field  and  p ress 
En te r.
9. Type add modem-pool next
 and  p ress 
En te r.
10. Typ e combined
 in the Group Type
 field.
11. Typ e 5
 in the Hold Time (min)
 field .
12. Typ e two-way
 in the Direction
 field .
13. Typ e 9600
 in the Speed
 field.
14. Typ e Full
 in the Duplex
 field .
15. Typ e async
 in the Synchronization
 field .
16. Typ e the p ort p air assig nments in the Analog
 and Digital
 fields and  
p ress 
En t e r.
Settings for Modem Connected to the Data 
Terminal Equipment (DTE)
1. Type add station next
 and press En t e r.
2. Type 2500
 in the Type
 field.
3. Typ e the p ort assig nment in the Port
 field  and  p ress 
En t e r. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-7 Add Pooled Modem 
A
7400A and 7400B Option Settings
Determine if the 7400A or 7400B will b e interfac ing with D-lead  modems or 
attention c ontrol mod ems. Use Ta b l e  A - 3
 to interfac e with either modem. You c an 
set op tions for the 7400B throug h a d umb  terminal. 
NOTE:
1. Set sp eed  to matc h remote mod em. At least one sp eed  must b e set ON.
NOTE:
2. Set to matc h remote mod em.
Table A-3. Options for D-Lead and Attention Control Modems
Set Option Display Option D-Lead 
SettingsAttention 
Control Settings
Set 300 Sp eed ? 300 Note 1 Note 1
Set 1200 Speed ? 1200 Note 1 Note 1
Set 2400 Speed ? 2400 Note 1 Note 1
Set 4800 Speed ? 4800 Note 1 Note 1
Set 9600 Speed ? 9600 Note 1 Note 1
Set 19200 Sp eed ? 19200 Note 1 Note 1
Set AT Control? AT OFF ON
Set CI Lead ? CI Note 2 Note 2
Set CI2 Lead ? CI2 Note 2 Note 2
Set CH Lead ? CH Note 2 Note 2
Set CH2 Lead ? CH2 Note 2 Note 2
Set LL Lead ? LL Note 2 Note 2
Set REMOTE Loop ? REMLOOP Grant Grant
Set RL Lead ? RL Note 2 Note 2
Se t  SI G L S D is c ? SI GL S D I SC ON ON
Set TM Lead ? TM Note 2 Note 2 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-8 Printer Option Settings 
A
Printer Option Settings
Printers c an b e used  with a manag ement terminal as journal p rinters for the 
hosp itality feature and  also as an outp ut devic e for Call Detail Rec ord ing  (CDR). 
A 572 printer c an func tion as a CDR d evic e, system p rinter, or journal p rinter. 
The op tions are set with func tion keys rather than DIP switc hes. Fig ure A -2
 shows 
the arrang ement of the func tion keys on the p rinter c ontrol p anel.
Figure A-2. Control Panel for 572 Printer
1. Load  the p rinter with p ap er and  turn the p ower off (Callout 1).
2. Simultaneously p ress and  hold  the Print Quality
 and  On Line
 b uttons. 
Press the Power On
 b utton. Release all three b uttons. The p rinter is now in 
set-up  mod e and  it p rints c urrent setting s:
If the p rinter is used with a management terminal, CDR, or as a Journal 
p rinter, set the op tions as shown in Ta b l e  A - 4
. If the p rinter is used  as the 
system p rinter, set the op tions as shown in Ta b l e  A - 5
.
3. Use Line Feed
 or Form Feed
 to step  throug h the op tions for the func tion.
4. Press On Line
. This ac tivates the menu for the func tion. Use Line Feed
 
and  Form Feed
 to step  throug h the op tions for the func tion.
5. When a d esired  op tion is loc ated , p ress Print Quality
. Eac h time an op tion 
is set, the setting  is p rinted . Rep eat for eac h op tion to be set.
6. When finished , p ress Print Quality
. The p rinter c hang es to normal mod e. Figure Notes
1. Power On Button
2. Alarm Button
3. Print Quality Button4. On Line Button
5. Line Feed  Button
6. Form Feed  Button
Power
OnAlarm Print
QualityOn
LineLine
FeedFo r m
Feed
345162 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-9 Printer Option Settings 
A
Table A-4. 572 Printer Used with Management Terminal 
Function Function Name Menu Menu Status
01 FORM LENGTH 09 11
02 LPI 01 6
03 CPI 01 10
04 LQ or NLQ 01 LQ
05 BUZZER 01 ON
06 FONT 02 FONTCART
07 RESOLUTION 01 144
1 1 B U FFER 0 2 N - L I N E
13 PW ON MODE 01 ON-LINE
14 DIRECTION 01 B1-DIR.1
15 BUFF FULL 02 LF +  CR
1 6 P. E. 0 1 AC TI VE
17 A UTO  CA RRIA GE RETURN ( CR) 01 CR +  LF
18 ZERO 01 0
22 AUTO LINE FEED 01 CR ONLY
311’’ SKIP 01 OFF
3 2 C H A R. SET ( GO ,  GL ) 0 2 U SA
33 CHAR.SET (G1, GR) 01 UK
34 CHAR SET (G2) 03 GE
35 CHAR SET (G3) 07 LINE DRAWING
81 OFF-LINE STATE 01 ALL RECEIVE
82 DSR 02 OFF
8 3 REQU EST TO  SEN D  ( RTS) TI M I N G 0 1 RTS
84 CD 02 OFF
8 5 C L EA R TO  SEN D  ( C TS) 0 2 O FF
91 OVER RUN 02 256
92 DATA BIT 02 8
93 PROTOCOL 03 XON/XOFF
94 STOP BIT 01 1
95 PARITY 01 NONE
96 PBS (matc hes c onnec ted  d evic e) 01 9600
Continued on next page 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Option Switch Settings 
A-10 Printer Option Settings 
A
Table A-5. 572 Printer used as System Printer 
Function Function Name Menu Menu Status
01 FORM LENGTH 09 11
02 LPI 01 6
03 CPI 01 10
04 LQ or NLQ 01 LQ
05 BUZZER 01 ON
06 FONT 02 FONTCART
07 RESOLUTION 01 144
11 BUFFER 02 N-LINE
13 PW ON MODE 01 ON-LINE
14 DIRECTION 01 B1-DIR.1
15 BUFF FULL 02 LF +  CR
16 P.E. 01 ACTIVE
17 AUTO CARRIAGE RETURN (CR) 01 CR +  LF
18 ZERO 01 0
22 AUTO LINE FEED 01 CR ONLY
311’’ SKIP 01 OFF
32 CHAR.SET (GO, GL) 02 USA
33 CHAR.SET (G1, GR) 01 UK
34 CHAR SET (G2) 03 GE
35 CHAR SET (G3) 07 LINE DRAWING
81 OFF-LINE STATE 01 ALL RECEIVE
82 DSR 02 OFF
8 3 REQ U EST TO  SEN D  ( RTS)  TI M I N G 0 1 RTS
84 CD 02 OFF
8 5 C L EAR TO  SEN D  (C TS) 0 2 OFF
91 OVER RUN 02 256
92 DATA BIT 02 8
93 PROTOCOL 03 XON/XOFF
94 STOP BIT 01 1
95 PARITY 01 NONE
96 PBS 04 1200