Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-113 Add IP Interface Assembly 
5
Figure 5-36. TN802B IP Interface faceplate
NOTE:
To p rop erly seat the c irc uit p ac k, p ush firmly on the front of the fac ep late 
until the latc h reac hes the b ottom rail of the c arrier. Then c lose the latc h 
until it is fully eng ag ed .
1. Insert the TN802B IP Interfac e into the rig htmost of the three slots you 
reserved  for it (see Fig ure 5-37
).
When you p lug  in the TN802B IP Interfac e, the c irc uit p ac k starts to b oot 
and  the LCD read s PC Boot 
then after ab out 3 to 4 minutes it c hang es to 
IP TRK *
, the default mod e. Figure Notes
1. LCD d isp lay
2. Reset b utton (rec essed )
3. Red  b oard  status LED4. PCMCIA c ard slot
5. Yellow PCMCIA d isk-in-use LED
1
2
3
4
5
fpdfmapd KLC 030899 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-114 Add IP Interface Assembly 
5
Figure 5-37. J58890MA-1 L30 IP Interface Assembly
Test the Modem
1. Check for dial tone.
2. Contac t Luc ent Tec hnolog ies Customer Sup p ort and  ask a rep resentative 
to d ial into your IP Interfac e server. 
Administer the IP Interface
Ad minstration is d one either loc ally or remotely. If ad ministered  loc ally, p roc eed  
with the following  ad minstration step s on the attac hed  keyb oard , mouse, and  
monitor. If administered  remotely, c all your servic e rep resentative to start the 
p roc ess.
456
789
1
0
1
11
21
3
1
41
51
6
indfmapd KLC 031299 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-115 Add IP Interface Assembly 
5
Administration Steps
1. Log in as craft
.
2. Type change circuit-pack
 and  p ress 
En te r.
3. Chec k the Cod e c olumn to see if the slots ab ove the TN802B say 
DSMAPD or MEDPRO.
.
4. If MEDPRO, g o to the entry just ab ove the TN802B that says MEDPRO.
5. Type DSMAPD, and press 
En te r. Chang ing the one entry automatic ally 
c hang es the entry ab ove it. If it is in IP Trunk mode, you g et the following 
error message:
MedPro type requires TN802 with application. Type 
MEDPRO on circuit-packs form.
Log onto the TN802B Interface Server 
If administered  remotely throug h p c ANYWHERE:
1. Dial in to the server through pcANYWHERE using the dialup number 
supplied. 
2. Clic k on the p c ANYWHERE Remote Host Computer b utton on the toolb ar 
to send  
CTRL ALT DEL to the host.
3. Type administrator
 in the User Name
 field .
4. Type iptrunk
 in the Password
 field  and  c lic k OK
. 
5. After log g ing  on for the first time, c hang e the ad ministrator p assword and , 
if d esired , the user name, to ensure sec urity. See your Wind ows NT server 
d oc umentation for d etails.
change circuit-packs                                            Page   1 of   5 
                              CIRCUIT PACKS                                     
        Cabinet: 1                            Carrier: A
                                         Carrier Type: processor        
 Slot Code  Sf Mode   Name               Slot Code  Sf Mode   Name
11: DSMAPD RESERVED-IP
01: TN754  DIGITAL LINE  12: DSMAPD  RESERVED-IP
02: TN758  POOLED MODEM  13: TN802  B  MAPD BOARD
03: TN2144  ANALOG LINE  14: 
04: TN746  B  ANALOG LINE  15: 
05 16:         
06: TN771  C  MAINTENANCE/TEST  
07: TN464  F  DS1 INTERFACE     
08: TN2140  E&M TIE TRUNK     
09: TN767  E  DS1 INTERFACE     
10: TN799  B  CONTROL-LAN       
  # indicates circuit pack conflict. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-116 Add IP Interface Assembly 
5
If administered  loc ally on a monitor, keyb oard, and  mouse:
1. Press 
CTRL, ALT, and  DEL simultaneously.
2. Type administrator
 in the User Name
 field .
3. Type iptrunk
 in the Password
 field  and  c lic k OK
. 
4. After log g ing  on for the first time, c hang e the ad ministrator p assword and , 
if d esired , the user name, to ensure sec urity. See your Wind ows NT server 
d oc umentation for d etails.
A-Law versus Mu-Law
For systems using  A-Law c omp and ing , an ad d itional p roc ed ure is nec essary. 
On the SAT:
1. Busyout the trunk g roup  assoc iated  with the IP trunk b y typing  busyout 
board 
UUCSS and  p ressing  En t e r.
In the Wind ows interfac e to TN802B:
1. Click on Control Panel > Services.
2. Highlight IP Trunk Service
, then c lic k on Stop
.
3. In the lower left-hand  c orner, rig ht-c lic k Start >  Exp lore.
4. Go to the c : d rive and  c lic k on its, then b in.
5. Double-c lic k on the its.ini file to op en it in Notep ad .
6. Und er the [ Med iaLib ]  sec tion, g o to COMPANDING= MLAW. Chang e 
MLAW
 to ALAW
.
7. Click on File > Save
 to save the file.
8. Click on File > Exit
 to exit Notep ad .
9. Click on Control Panel > Services.
10. Highlight IP Trunk Service
, then c lic k on Start
.
NOTE:
Do not selec t Startup .
After servic e has started , g o to the SAT:
1. Release the trunk g roup  assoc iated  with the IP trunk b y typing  release 
board
 
UUCSS and  p ressing  En t e r. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-117 Add IP Interface Assembly 
5
Assign Server and Domain Names
The Windows NT server identifies servers using a server name plus a domain 
name that loc ates the named  server in a p artic ular p art of the network. The 
TN802B IP Interfac e is ship p ed  with generic  server and  d omain names. Assig n 
rep lac ement names that are meaning ful within your network. 
1. Click on My Computer > Control Panel > Network
.
2. Selec t the Identification
 tab , then c lic k Change
.
3. Typ e the new server name in the Computer Name 
field .
4. Typ e the new d omain name in the Domain
 field and  c lic k OK > OK > 
Close
.
5. When p romp ted  to reb oot the c omp uter, selec t one of the following  
op tions:
nNo
 if you have not assigned  IP ad d resses then g o to ‘‘Assig n an IP 
Address’’
nYe s
 if you have assigned  IP ad dresses. 
Assign an IP Address
1. Click on My Computer > Control Panel > Network
.
2. Click the Protocols
 tab .
3. Select TCP/IP Protocol 
from the list.
4. Click the Properties
 op tion in the Network wind ow.  
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-118 Add IP Interface Assembly 
5
5. Verify that the Adapter
 drop  d own menu lists 2 DEC Ethernet ad ap ters.
!CAUTION:
Do not c hange any setting s on the ad ap ter lab eled  [ 1]  for any 
reason.
6. Selec t the DEC Ethernet ad ap ter lab eled  [ 2] . 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-119 Add IP Interface Assembly 
5
7. Typ e a valid  IP ad d ress for the IP Interfac e server in the IP Address:
 
field .
8. Typ e the ap p rop riate sub net mask in the Subnet Mask:
 field. 
NOTE:
Not all networks req uire step s 9 throug h 18. Chec k with the loc al 
network ad ministrator to determine whic h are req uired .
9. If you use g ateways, type the IP ad d ress of the d efault g ateway for the IP 
Interfac e server in the Default Gateway:
 field.
10. Clic k on the DNS tab  and  verify that the d omain DNS server is c orrec t. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-120 Add IP Interface Assembly 
5
11. Typ e d omain name in the Domain
 field .
12. If using  DNS, c lic k 
Add  under the DNS Service Search Order
 field  and 
type its IP ad d ress.
13. Clic k on the WINS Ad dress tab . 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-121 Add IP Interface Assembly 
5
14. Make sure the [ 2]  DEC shows in the Adapter
 field.
15. If WINS server is availab le, typ e its IP ad d ress in the Primary WINS 
Server
 field .
16. If DNS is availab le, selec t Enable DNS for Windows Resolution
.
17. If the network uses an imp orted LMHOSTS file, selec t Enable LMHOSTS 
Lookup 
and Import LMHOSTS
 and c lic k OK
.
18. If the following  d ialog  b ox op ens, c lic k Ye s
:
At least one of the adapter cards has an empty primary 
WINS address. Do you want to continue?
19. Clic k the Bindings
 tab  to effec t the c hang es.
NetBIOS Interface, Server, and Workstation should now be enabled. If any 
are d isab led  (a red  c irc le with a line throug h it), review the p revious 
network-c onfig uration step s for omissions or errors.
20. Clic k Close
. 
						

							DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-122 Add IP Interface Assembly 
5
If administered  remotely throug h p c ANYWHERE:
21. Clic k on the p c ANYWHERE Restart Host Comp uter b utton on the toolb ar 
to restart the c omputer.
If administered  loc ally on a monitor, keyb oard, and  mouse:
21. Clic k Ye s
 in the d ialog  b ox to restart the c omp uter. 
!WARNING:
When c onnec ted  remotely via p c ANYWHERE, only use the p c ANYWHERE 
Restart Host Computer b utton on the toolb ar to restart Wind ows NT.
Check Network Services
When the server restarts, make sure that the req uired  network servic es have 
started c orrec tly. If you see an error d ialog  b ox, then the network servic es d id  not 
start c orrec tly. Also, c hec k the NT Event Log.
1. Click on My Computer > Control Panel > Network > Services. 
Make 
sure that the following  servic es are listed:
nComp uter Browser
nMic rosoft Internet Information Server 2.0
nNetBIOS Interfac e
nRPC Config uration
nSe r ve r
nWorkstation
2. Click the Protocols 
tab , and examine the Network Protoc ols. TCP/IP 
p rotoc ol should  b e the only one listed .
3. Click OK
.
Test the External Connection to the LAN
To test the external IP c onnec tions, p ing  the IP Interfac e server and  p ing  a known 
c omp uter c onnec ted  to your network.
1. Click Start > Programs > Command Prompt
.
2. Type ping 
nnn.nnn.nnn.nnn (whic h is your IP ad d ress).
nIf everything  is c onfigured  c orrec tly, the system respond s with the 
following message:
Reply from nnn.nnn.nnn.nnn: bytes=32 time