Kyocera TASKalfa 552ci User Manual

							Preparation before Use
2-15
2
8After changing the setting, restart the system or 
turn the machine OFF and then ON again. 
For detailed information on restarting the system, 
refer to Restarting the System on page 8-72.
Auto-IP Settings
Select whether or not to use Auto-IP. The default setting is On.
Use the procedure below.
1Press the System Menu key.
2Press [System], [Next] of Network and then [Next] 
of TCP/IP Setting.
3Press [Change] of TCP/IP.
4Press [On] and then press [OK].
5Press [Change] of IPv4.
6Press [Auto-IP].
7Press [On] or [Off] of Auto-IP and then press [OK].
8After changing the setting, restart the system or 
turn the machine OFF and then ON again. 
For detailed information on restarting the system, 
refer to Restarting the System on page 8-72.
AppleTalk Setup
Select the Apple Talk network connection. The default setting is On.
Use the procedure below.
1Press the System Menu key.
2Press [System], [Next] of Network and then 
[Change] of AppleTalk.
3Press [On] or [Off].
4Press [OK].
5After changing the setting, restart the system or 
turn the machine OFF and then ON again. 
For detailed information on restarting the system, 
refer to Restarting the System on page 8-72.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-16
Installing Software
Install appropriate software on your PC from the included Product Library CD-ROM (Product Library) if you want 
to use the printer function of this machine or perform TWAIN / WIA transmission or FAX transmission from your 
PC.
NOTE: Installation on Windows must be done by a user logged on with administrator privileges.
Plug and Play is disabled on this device when in Sleep. Wake the device from Low Power Mode or Sleep before 
continuing. See Low Power Mode and Auto Low Power Mode on page 2-9 and Sleep and Auto Sleep on page 
2-10.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-17
2
COMMAND CENTER (Settings for E-mail)
COMMAND CENTER is a tool used for tasks such as verifying the operating status of the machine and changing 
the settings for security, network printing, E-mail transmission and advanced networking.
NOTE: Here, information on the FAX settings has been omitted. For more information on using the FAX, refer 
to the Fax Kit Operation Guide.
The procedure for accessing COMMAND CENTER is explained below.
1Launch your Web browser.
2In the Address or Location bar, enter the machine’s IP address.
E.g.) http://192.168.48.21/
The web page displays basic information about the machine and COMMAND CENTER as well as their 
current status.
3Select a category from the navigation bar on the left of the screen. The values for each category must be 
set separately.
If restrictions have been set for COMMAND CENTER, enter the correct user name and password to access 
pages other than the startup page.
For details, refer to the KYOCERA COMMAND CENTER Operation Guide.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-18
Sending E-mail
Specifying the SMTP settings allows you to send images loaded onto this machine as E-mail attachments. 
To use this function, this machine must be connected to a mail server using the SMTP protocol.
Before sending images loaded onto this machine as E-mail attachments, check the following:
• The network environment used to connect this machine to the mail server
A full-time connection via a LAN is recommended.
• SMTP Settings
Use COMMAND CENTER to register the IP address or host name of the SMTP server.
• If limits have been set on the size of E-mail messages, it may not be possible to send very large E-mails.
The procedure for specifying the SMTP settings is explained below.
1Click Advanced -> SMTP -> General.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-19
2
2Enter the correct settings in each field.
The settings to be specified in the SMTP settings screen are shown below.
3Click Submit.Item Description
SMTP ProtocolEnables or disables SMTP protocol. To use E-mail, this protocol must be 
enabled.
SMTP Port NumberSet the SMTP Port Number or use the SMTP default port 25.
SMTP Server NameEnter the SMTP server IP address or its name. The maximum length of the 
SMTP server name and IP address is 64 characters. If entering the name, a DNS 
server address must also be configured. The DNS server address may be 
entered on the TCP/IP General tab.
SMTP Server TimeoutSet the amount of time to wait before time-out in seconds.
Authentication 
ProtocolEnables or disables the SMTP authentication protocol or sets POP before SMTP 
as the protocol. The SMTP authentication supports Microsoft Exchange 2000.
Authenticate asAuthentication can be set from three POP3 accounts or you can choose a 
different account.
Login User NameWhen Other is selected for Authenticate, the login user name set here will be 
used for SMTP authentication. The maximum length of the login user name is 
64 characters.
Login PasswordWhen Other is selected for Authenticate, the password set here will be used for 
authentication. The maximum length of the login password is 64 characters.
POP before SMTP 
TimeoutSet the amount of time to wait before time-out in seconds when you have 
selected POP before SMTP as the Authentication Protocol.
TestThis will test if the SMTP connection can be successfully established.
E-mail Size LimitEnter the maximum size of E-mail that can be sent in kilobytes. When the value is 
0, the limitation for E-mail size is disabled.
Sender AddressEnter the E-mail address of the person responsible for the machine, such as the 
machine administrator, so that a reply or non-delivery report will go to a person 
rather than to the machine. The sender address must be entered correctly for 
SMTP authentication. The maximum length of the sender address is 
128 characters.
SignatureEnter the signature. The signature is free form text that will appear at the end of 
the E-mail body. It is often used for further identification of the machine. The 
maximum length of the signature is 512 characters.
Domain RestrictionEnter the domain names that can be permitted or rejected. The maximum length 
of the domain name is 32 characters. You can also specify E-mail addresses.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-20
Loading Paper
Paper can be loaded standardly in the two cassettes and the multi purpose tray. A paper feeder is also available 
as an option (refer to Optional Equipment on Appendix-2).
Before Loading Paper
When you open a new package of paper, fan the sheets 
to separate them slightly prior to loading in the following 
steps.
1Bend the whole set of sheets to swell them in the 
middle.
2Hold the stack at both ends and stretch it while 
keeping the entire stack risen.
3Raise the right and left hands alternately to create 
a gap and feed air between the paper.
4Finally, align the paper on a level, flat table.
If the paper is curled or folded, straighten it before 
loading. Paper that is curled or folded may cause a 
jam.
CAUTION: If you copy onto used paper (paper already 
used for copying), do not use paper that is stapled or 
clipped together. This may damage the machine or 
cause poor image quality.
NOTE: If printouts are curled or not neatly stapled, 
turn the stack in the cassette upside down.
Avoid exposing opened paper to high temperatures 
and high humidity as dampness can be a cause of 
problems. Seal any remaining paper after loading 
in the multi purpose tray or cassettes back in the 
paper storage bag.
If the machine will not be used for a prolonged 
period, protect all paper from humidity by removing 
it from the cassettes and sealing it in the paper 
storage bag.
NOTE: If you use special paper such as letterhead, 
paper with holes or paper with pre-prints like logo or 
company name, refer to the Paper on Appendix-10.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-21
2
Loading Paper in the Cassettes
The 2 standard cassettes will each hold plain paper, recycled paper or color paper. 
Cassette 1 holds up to 500 sheets of A4 or smaller plain paper  (80 g/m
2) or up to 250 sheets of B4 or larger 
plain paper (80 g/m
2). Cassette 2 holds up to 500 sheets of plain paper (80 g/m2) (or up to 550 sheets of 64 g/
m
2 plain paper).
The following paper sizes are supported: Ledger, Legal, Oficio II, 8.5×13.5, Letter, Letter-R, Statement, A3, 
B4, A4, A4-R, B5, B5-R, A5, Folio, 8K, 16K, and 16K-R.
IMPORTANT: 
• For clearer and brighter color copies, use the special color paper. 
You should not use inkjet printer paper or any paper with a special surface coating. (Such paper may cause 
paper jams or other faults.)
• When using media types other than plain paper (such as recycled or colored paper), always specify the 
media type setting. (Refer to Specifying Paper Size and Media Type for the Cassettes on page 2-28)
The cassettes can hold paper with weights up to 163 g/m
2. If you are using a paper weight between 106 
and 163 g/m2, set the media type to Thick.
• Do not load thick paper that is heavier than 163 g/m
2 in the cassettes. Use the multi purpose tray for paper 
that is heavier than 163 g/m2.
1Pull the cassette out toward you until it stops.
NOTE: Do not pull out more than one cassette at a 
time.
2Using the paper length guide, move the plate to fit 
the paper.
When loading A4 or smaller paper into cassette 1, 
lift up the paper length guide. For B4 or larger 
paper, lower the paper length guide.
NOTE: Paper sizes are marked on the cassette.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-22
3Holding the paper width adjusting tab, move the 
paper width guides to fit the paper.
NOTE: Paper sizes are indicated on the cassettes.
To change between inch size and metric size (A, B 
sizes), follow the steps below to adjust the size switch.
1. Holding the paper width adjusting tab, move the 
paper width guide to a position other than that of the 
paper.
2. Turn the size switch A 90°. 
> 
3. Move the size lever B up (C) or down (I). 
    C:metric size (centimeters) (A, B sizes)
     I:inch size
4. Turn the size switch 90°to lock it.
 >
4Align the paper flush against the left side of the 
cassette.
A
B
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-23
2
IMPORTANT: 
• Before loading the paper, be sure that it is not 
curled or folded. Paper that is curled or folded may 
cause paper jams.
• Ensure that the loaded paper does not exceed the 
level indicator (see illustration below).
• When loading the paper, keep the side that was 
closest the package seal facing up.
• The paper length and width guides must be 
adjusted to the paper size. Loading the paper 
without adjusting these guides may cause skewed 
feeding and paper jams.
• Be sure that the paper length and width guides rest 
securely against the paper. If there is a gap, 
readjust the guides to fit the paper.
5Insert the appropriate paper size card in the slot to 
indicate the size of the paper inside.
6Gently push the cassette back in.
NOTE: If the machine will not be used for a prolonged 
period, protect all paper from humidity by removing it 
from the cassettes and sealing it in the paper storage 
bag.
7Select the media type (plain, recycled, etc.) loaded 
in the cassette. (Refer to Specifying Paper Size 
and Media Type for the Cassettes on page 2-28.)
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use
2-24
Loading Paper in the Multi Purpose Tray
The multi purpose tray will hold up to 100 sheets of A4 or smaller plain paper (80 g/m2) or up to 50 sheets of 
plain paper (80 g/m
2) lager than A4.
The multi purpose tray accepts paper sizes from A3 to A6 and Hagaki and from Ledger to Statement-R, 8K, 16K 
and 16K-R. Be sure to use the multi purpose tray when you print on any special paper.
IMPORTANT: When using media types other than plain paper (such as recycled or colored paper), always 
specify the media type setting. (Refer to Specifying Paper Size and Media Type for the Multi Purpose Tray on 
page 2-30.) If you are using a paper weight of 106 g/m2 or more, set the media type to Thick.
The capacity of the multi purpose tray is as follows.
• A4 or smaller plain paper (80 g/m
2), recycled paper or color paper: 100 sheets
• B4 or larger plain paper (80 g/m
2), recycled paper or color paper: 50 sheets
• Hagaki: 30 sheets
• OHP film: 10 sheets
• Envelope DL, Envelope C5, Envelope #10 (Commercial #10), Monarch, Youkei 4, Youkei 2: 10 sheets
NOTE: When you load custom size paper, enter the paper size by referring to Specifying Paper Size and 
Media Type for the Multi Purpose Tray on page 2-30.
When you use special paper such as transparencies or thick paper, select the media type by referring to 
Specifying Paper Size and Media Type for the Multi Purpose Tray on page 2-30.
1Open the multi purpose tray.
2When loading paper sizes from A3 to B4 and 
Ledger to Legal, extend the support tray section of 
the multi purpose tray.
Downloaded From ManualsPrinter.com Manuals