Honda Bmw 5 Service Manual
Have a look at the manual Honda Bmw 5 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 328 Honda manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
411-3 Doors 4 Pull up on locking clip and remove connector. 4 With door fully open, unscrew pin bolts (arrow) from top and bottom hinges. Disconnect door check by squeezing mounting pin tabs (arrow) and driving pin up. Remove door by lifting up off lower hinge halves. CAUJION- Be careful not to damage door or otherpainted body surfac- es. Make sure no load is placed on wirinq harness. Installation is reverse of removal. Keep in mind the following: Mount and align rear doors first, followed by the front doors. Align door so that panel gaps are equal on either side, see specifications at the end of this procedure. If necessary, adjust door hinges. See Door hinge adjustment. * Adjust door striker so that trailing edge of front door is slightly higher (I mm 10.04 in.) than leading edge of rear door. See 515 Central Locking and Anti-Theft. Repair any paint damage and paint any exposed metal.
Doors ~obr adjustment Front fender to 4.25 mm i 0.25 mm (0.17 i- 0.01 in) front door gap Front door to 4.5 mm i 0.25 mm (0.18 i 0.01 in) rear door gap Rear door to rear fender 4.0 mm i 0.25 mm (0.16 i 0.01 in) Permissible deviation 1 .O mm (0.04 in) from ~arallel Tightening torque Door hinge to door frame 20 Nm (15 it-lb) Door check, replacing WARNING - E39 cars are fitted with side-impact airbags in the front doors and optional side impact airbags in the rear doors. When servicing doors, always disconnect the negative (-) battery terminal. See 721 Airbag System (SRS) for cautions and procedures relating to the airbag system. - Close door window completely. - Disconnect negative (-) battery cable. CAUTION- Prior to disconnecting the batter)! read the battery discon- nection cautions given in 001 General Cautions and Warnings. - Remove interior door panel. See Door trim panels, remov- ing and installing. - Where applicable, remove side-impact airbag from door. See 721 Airbag System (SRS). Remove door vapor barrier. Disconnect door check by (arrow) and removing pin. squeezing I mounting pin tabs
... - Doors Remove rubber cover (A) and bolts (B) from door check lock- plate on door. Worlting inside door, remove door check assembly Installation is reverse of removal. Lubricate door check before installing. - If removed, use new mounting bolts when reinstalling side- impact airbag to door. Tightening torque Door check to door frame 24 Nm (16 it-lb) Door hinge adjustment If the installed door is uneven or out of parallel, spacers can be used to correct its position. Spacers are placed behind the hinge and are available in two different thicltnesses (0.5 mm and 1.0 mm). - Front and rear door adjustment procedure is similar. Tightening torque Door hinge to door frame 20 Nrn (15 ft-lb)
. 1 Doors Door hinge assembly 1. Door 2. Spacer ring 3. Upper hinge 4. Hex bolt 5. Spacer ring 6. Lower hinge 7. Door check gasket 8. Doorcheck 9. Pin 10. Torx bolt 11. Gasket 12. Cover
WARNING - E39 cars are fitted with side-impact airbags in the front doors and optional side impact airbags in the rear doors. When servicing doors, always disconnect the negative (-) battery terminal. See 721 Airbag System (SRS) for cautions and procedures relating to the airbag system. Door trim panel, removing and installing Disconnect negative (-) battery cable. CAUTION-- Prior to disconnecting the battem read the batfew discon- nection cautions given in 001 General Cautions and warn- ings. Q Open door, and remove screw (arrow) located in air duct. < Pry out seat memory switch and disconnect wiring harness.
411-8 Doors < Pry off plastic plug (arrow) from door handle trim and remove screw. 4 Carefully pry out window switch panel and disconnect elec- trical harness plugs. < Slide door handle through trim panel
I < Unclip door panel from door perimeter using a plastic trim panel tool. Pry panel retaining clips off one at a time. - Lift bottom of door trim panel up and away from window trim to release clips. - Pull door panel upwards to release center mount clip. - Disconnect radio speaker wiring harness. - Remove door trim panel. < Before installing door trim panel, replace any damaged plas- tic clips (arrows). NOTE- Yellow door trim clips (white arrows) at front are longer than white door trim clips (blaclc arrows). 4 Checlt if support clip for door bracltet remains on door (ar- row). 4 If so, remove support clip from door and replace in bracltet on door trim panel (arrow). - Remainder of installation is reverse of removal. Note the fol- lowing: Align metal retainers on window sill with openings on top of door panel. Checlc door-lock mechanism and window for ease of movement.
411-10 /Doors Sill trim panels Using a trim tool, gently pry up door sill trim. Starting at A-pil- lar, press radius of trim downwards while sliding trim forward off trim clips. Remove clips from body using pliers. Save for installation. Installation is reverse of removal. Replace any damaged plastic parts or clips.
41 2 Trunk Lid. Tailgate ........................... General ......................... Trunk Lid Trunlc lid. removing and installing ........ Trunk lid. adjusting ................... Trunk lid support strut. removing and installing ................ Tailgate (Sport Wagon Models) ..... Tailgate. emergency release ........... Tailgate and window strut diagram ....... Window strut removal diagram .......... 412-8 Rear window gas strut. removing and installing ................ 412-9 Tailgate gas strut. removing and installing ............... 412-10 Tailgate. removing and installing ........ 412-1 1 Rear window. removing and installing .... 412-12 Rear window and tailgate. alignment ..... 412-13
41 2-2 Trunk Lid, Tailgate This repair group covers trunk lid and tailgate removal and in- stallation. Also included here are replacement proceduresfor the gas-charged support struts that hold the trunk lid or tail- gate in the open position. NO JE - The body is painted at the factory after assembly. Realign- ment of body panels may expose unpainted metal. Paint all exposed metal once the work is complete. Trunk lid, removing and installing 4 Raise trunlc lid. Open tool ltit cover and remove screws attaching tool kit to trunlc lid (black arrows). Disconnect tool ltit cover retaining strap from trunk lid and remove tool kit. Remove insulating liner expansion rivets (white arrows). 4 Pry out moulded trim cover (arrow).